engine overheat MINI Coupe 2012 Owner's Manual
[x] Cancel search | Manufacturer: MINI, Model Year: 2012, Model line: Coupe, Model: MINI Coupe 2012Pages: 218, PDF Size: 3.84 MB
Page 34 of 218
Opening and closingCONTROLS
33
The warning lamp lights up when the
engine is running: the remote control is
no longer inside the vehicle. After the
engine is switched off, the engine can only be
restarted within approx. 10 seconds.
The indicator lamp comes on: replace
the battery in the remote control.
Replacing the battery
The remote control for Comfort Access contains
a battery that will need to be replaced from time
to time.
1. Remove the cover.
2. Insert the new battery with the plus side
facing up.
3. Press the cover on to close.
Take the old battery to a recycling center
or to your MINI dealer. <
Windows
To prevent injuries, exercise care when
closing the windows.
Take the remote control with you when you
leave the car; otherwise, children could operate
the electric windows and possibly injure them-
selves. <
If, after a window is opened and closed
several times in close succession, the
window can only be closed and not opened, the
system is overheated. Let the system cool for
several minutes with the ignition switched on or
the engine running. <
Opening
>Press the switch downward.
The window opens until you release the
switch.
> Push the switch downward.
As of radio readiness, the windows will open
automatically. Push the switch again to stop
the opening movement.
To open the window a crack, press the switch
down twice in quick succession.
Closing
In order to close the window, press the switch
up. The window closes until you release the
switch.
Initializing electric power windows
If the battery was disconnected, e.g. for
changing batteries or vehicle storage,
reinitialize the power wi ndows; otherwise, the
windows will not be lowered.<
1. Close the doors.
2. Open both windows.
3. Close both windows.
In the event of a system malfunction, please
contact your MINI dealer.
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG
Page 57 of 218
CONTROLSDriving
56
Radio readiness and ignition off
All indicator and warning lamps in the displays
go out.
The ignition switches off automatically if the
driver's door is opened. Pressing the Start/Stop
button again switches the ignition back on.
The ignition is not switched off in situations such
as the following:
> The clutch or brake is depressed
> The low beams are switched on
Starting the engine
Do not allow the engine to run in enclosed
areas; otherwise, inha lation of the noxious
exhaust gases can lead to loss of consciousness
and death. Exhaust gases contain carbon
monoxide, an odorless and colorless, but highly
toxic gas. Never leave an unattended vehicle
with the engine running; otherwise, such a
vehicle represents a potential safety hazard.
Before leaving the car while the engine is run-
ning, place the transmission in neutral or move
the selector lever to position P and forcefully
apply the parking brake to prevent the car from
moving. <
Avoid frequent starting in quick succes-
sion or repeated start attempts in which
the engine does not start. Otherwise, the fuel is
not burned or inadequate ly burned and there is
a danger of overheating and damaging the
catalytic converter. <
Do not let the engine warm up with the vehicle
at a standstill. Move off immediately at a
moderate engine speed.
When starting the engi ne, do not depress the
accelerator pedal.
Manual transmission
Key in ignition lock or inside vehicle with
Comfort Access, refer to page 31.
1. Depress the brake.
2. Depress the clutch.
3. Press the Start/Stop button.
Automatic transmission
Key in ignition lock or inside vehicle with
Comfort Access, refer to page 31.
1. Depress the brake.
2. Shift the selector lever into position P or N.
3. Press the Start/Stop button.
The starter operates auto matically for a certain
time, and stops automati cally as soon as the
engine has started.
Switching off the engine
Always take the key with you when you
leave the vehicle.
When parking, apply the parking brake force-
fully; otherwise, the vehicle could begin to roll.
Secure the vehicle on steep upward and down-
ward slopes, for example, turn the steering
wheel towards the curb. <
Manual transmission
1.With the car at a standstill, press the Start/
Stop button.
2. Shift into first gear or reverse.
3. Forcefully apply the parking brake.
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG
Page 80 of 218
Technology for driving comfort and safetyCONTROLS
79
For information on car washing facilities and
care, refer to page161 and following.
Automatic mode
When starting the engine, a retracted rear
spoiler is in the automa tic mode. It is possible
that there will be some noise for a short time
when driving off because of the initialization of
the system.
Automatic extension:
When driving at speeds in excess of approx.
50 mph/80 km/h.
Automatic retraction:
When driving at speeds below 38 mph/60 km/h.
In the automatic mode, the rear spoiler
can not be retracted manually at speeds
greater than 37 mph/60 km/h. <
Manual mode
The manual mode can, for example, be used
when cleaning the rear spoiler while the ignition
is on or the engine is running. LED on switch is
on.
If the rear spoiler stops in an intermediate
position after repeat edly being extended
and retracted, then the system has become
overheated. After a short cooling down time, the
rear spoiler can again be operated.<
Extending rear spoiler
Press the switch toward the rear.
Retracting rear spoiler
If the rear spoiler was manually extended and
a speed of 50 mph/80 km/h not exceeded, then
the rear spoiler can again be retracted. Other-
wise, the rear spoiler cannot be retracted unless
the speed is below 37 mph/60 km/h.
> For speeds between 12 mph/20 km/h and
50 mph/80 km/h,
briefly press the switch forward or keep
pressed.
> For speeds less than 12 mph/20 km/h,
press switch forward and keep pressed.
Malfunctions
Indicator lamp goes on briefly when the
ignition is switched on and an acoustic
signal is produced.
Display in the following situations:
> Rear spoiler is extended.
Manually retract rear spoiler or it will
automatically retract at a speed of approx.
12 mph/20 km/h.
> Rear spoiler can not be extended from the
rear spoiler compartment.
Check if the rear spoiler is free of snow or ice,
for example. Free rear spoiler or clear of ice.
Warning lamp goes on and an acoustic
signal sounds several times.
Display in the following situation:
The rear spoiler can not be completely
extended; do not exceed a speed of 50 mph or
80 km/h.
Have the system checked.
When there is a malfunction at speeds greater
than 30 mph/50 km/h, the Dynamic Stability
Control DSC switches on.
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG
Page 108 of 218
Things to remember when drivingDRIVING TIPS
107
Hot exhaust system
As in all vehicles, extremely high tempera-
tures are generated on the exhaust sys-
tem. Do not remove the heat shields installed
adjacent to various se ctions of the exhaust
system, and never apply undercoating to them.
Make sure that when driving, idling or when
parking, no easily flamma ble materials, such as
hay, leaves, grass, etc. come into contact with
the hot exhaust system. Such contact could lead
to a fire, with the risk of serious personal injuries
and property damage. Do not touch hot exhaust
tail pipes. Otherwise, there is a risk of burns. <
Hydroplaning
When driving on wet or slushy roads,
reduce road speed. If you do not, a wedge
of water can form betw een tires and road sur-
face. This situation, known as hydroplaning, can
cause partial or complete loss of tire contact
with the road surface, so that the car cannot be
steered or braked properly. <
The risk of hydroplaning increases with declining
tread depth on the tires, refer also to Tread
depth on page 151.
Driving through water
Drive through water on the road only if it is
not deeper than 1 ft/30 cm, and then only
at walking speed at the most. Otherwise, the
vehicle's engine, the electrical systems and the
transmission may be damaged. <
Parking brake on inclines
On inclines, do not hold the vehicle with
the clutch; use the parking brake. Other-
wise, greater clutch wear will result. <
For information on drivin g off using Hill Assist,
refer to page 78.
Braking safely
Your MINI is equipped with ABS. If you are in a
situation which requires full braking, it is best to
brake using maximum brake pressure. Since the
vehicle maintains steeri ng responsiveness, you can still avoid possible obstacles with a mini-
mum of steering effort.
The pulsation of the brake pedal, together with
the sound of hydraulic regulation, indicates that
ABS is functioning properly.
Objects in the movement range of the
pedals
Keep floor mats, carp
et, and other objects
out of the movement range of the pedals;
otherwise, they may inhi bit the function of the
pedals during driving.
Do not place additional floor mats onto an
existing one or onto other objects.
Only use floor mats that have been approved for
the vehicle and can be appropriately fastened.
Make sure that the fl oor mats are securely
fastened again after they have been removed,
e.g. for cleaning. <
Driving in wet conditions
When roads are wet or ther e is heavy rain, briefly
exert gentle pressure on the brake pedal every
few miles. Monitor traffic conditions to ensure
that this maneuver does not endanger other
road users. The heat generated in this process
helps dry the pads and rotors to ensure that.
Then full braking force will be immediately
available when it is needed.
Hills
To prevent overheatin g and the resulting
reduced efficiency of the brake system,
drive long or steep downhill gradients in the
gear in which the least braking is required. Even
light but consistent brake pressure can lead to
high temperatures, brake wear and possibly
even brake failure. <
You can increase the engine's braking effect by
shifting down, all the way to first gear if neces-
sary. This strategy helps you avoid placing
excessive loads on the brake system. Downshift-
ing in manual mo de of the automatic transmis-
sion, page 59.
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG
Page 159 of 218
MOBILITYEngine compartment
158
Coolant
Coolant consists of half water and half additive.
Not all commercially available additives are
suitable for your MINI. Your MINI dealer knows
which additives are suitab le and will be glad to
advise you.
Only use suitable additives; otherwise,
engine damage may result. Because
additives are harmful to your health, it is
important to follow the instructions on the
containers. <
Comply with the appropriate environmen-
tal protection regulations when disposing
of coolant additives. <
Coolant temperature
If the coolant, and therefore the engine, should
overheat, then a warning lamp will go on, refer
to page185.
Checking coolant level
Do not add coolant to the cooling system
when the engine is hot. Escaping coolant
can cause burns. <
Do not open the hood until the engine has
cooled down.
The coolant level is correct if it is between the
marks.
Topping off
1. Turn the cap of the ex pansion tank a little
counterclockwise to allow any accumulated pressure to escape, then continue turning to
open.
2. Slowly fill to the correct fluid level; do not
overfill.
3. Close by turning the cap.
Have the reason for the coolant loss eliminated
as soon as possible.
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG
Page 173 of 218
MOBILITYReplacing components
172
4.Unscrew the dust cap from the valve of the
defective wheel and screw the filling hose 2
of the sealant bottle onto the valve.
5. Ensure that the compre ssor is switched off.
6. Insert the plug 5 into the lighter socket/
power socket in the vehicle interior,
page 102.
7. With the engine running:
Switch on the compressor and let run for
about 3 to 8 minutes in order to add the
sealant and to achieve an inflation pressure
of about 1.8 bar/26 psi.
When adding the sealant, the filling
pressure can temporarily increase up
to about 5 bar/73 psi. Do not switch off the
compressor during this phase. <
Do not run the comp ressor for longer
than 10 minutes; otherwise, the
device will overheat and possibly be
damaged.<
8. Switch off the compressor.
If an inflation pressure of 1.8 bar/26 psi is not
reached:
1. Unscrew the filling hose 2 from the wheel
and drive the vehicle forward and backward
approx. 33 ft/10 m to distribute the liquid
sealant in the tire evenly.
2. Inflate the tire again with the compressor.
If an inflation pressure of 1.8 bar/26 psi is
not reached, then the tire is too badly
damaged. Please contact the nearest MINI
dealer. <
Stowing Mobility Kit
1.Unscrew filler hose 2 of the sealant bottle
from the wheel.
2. Unscrew connecting hose of the
compressor 6 from the sealant bottle.
3. Connect the filler hose 2 of the sealant
bottle to the unoccupied connection on
the sealant bottle.
This prevents the rest of the sealant from
escaping from the bottle.
4. Wrap the empty sealant bottle in suitable
material to avoid dirtying the cargo area.
5. Stow Mobility Kit back in the vehicle.
Distributing the sealant.
Immediately drive appr ox. 3.1 miles/5 km so
that the sealant evenly distributes itself.
Do not exceed speeds of 50 mph/
80 km/h.
If possible, do not drop below 10 mph/
20 km/h. <
Adjusting the tire pressure
1.After driving approx. 3.1 miles/5 km or
10 minutes, stop at a suitable location.
2. Screw the connection hose 6 of the com-
pressor directly onto the tire valve.
3. Insert the plug 5 into the power socket in
the vehicle interior.
4. Adjust tire pressure to 1.8 bar/26 psi. With
the engine running:
> To increase the inflatio n pressure: switch on
the compressor. To ch eck the current infla-
tion pressure, switch off the compressor.
Do not run the compressor for longer
than 10 minutes; otherwise, the
device will overheat and possibly be
damaged. <
> To decrease the inflat ion pressure: press the
release button 9.
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG
Page 186 of 218
Indicator and warning lampsMOBILITY
185
Lights up in red:
Engine malfunctionStop the car and switch off the
engine. You cannot continue your
journey. Contact your MINI dealer.
Lights up in yellow:
Full engine power no longer available Y ou can continue your journey, but
moderate your speed and exercise
due caution. Have the engine
checked as soon as possible.
Indicator lamp 1 flashes:
Engine malfunction under high load.
High engine load will result in
damage to the catalytic converter You can continue your journey, but
moderate your speed and exercise
due caution. Have the vehicle
checked without delay.
Indicator lamp 1 comes on:
Engine malfunction with adverse
effect on exhaust emissions You can continue your journey, but
moderate your speed and exercise
due caution. Have the car checked as
soon as possible.
Lights up in red:
Engine overheating Carefully bring the car to a stop,
switch off the engine and allow it to
cool down. Do not open the hood;
otherwise, there is a risk of injury from
scalding. Contact your MINI dealer.
Lights up in yellow:
Engine too hot Continue driving at more moderate speed so that the engine can cool
down. Have the engine checked
without delay if the situation reoccurs.
12Cause What to do
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG
Page 192 of 218
Indicator and warning lampsMOBILITY
191
Lights up in red:
>Transmission limp-home pro-
gram active with restricted range
of gears, possibly with reduced
acceleration You can continue your journey, but
moderate your speed and exercise
due caution. Have the system
checked without delay.
> Gears can be engaged without
depressing the brake Always depress the brake to engage a
gear.
> Automatic selector lever locked Manually releasing the selector lever
lock, page59.
Lights up in yellow: Have the system checked as soon as
possible.
> Automatic selector lever locked:
Selector lever locked in position P
with engine running and brake
depressed or Manually releasing the selector lever
lock, page
59.
> Brake signal malfunctioning:
gear can be engaged without
depressing the brake To engage a gear while the vehicle is
at a standstill, always depress the
brake. Before leaving the vehicle,
move the selector lever to position P
and switch off the engine.
Lights up in red:
Transmission overheating Bring the car to a stop and move the
selector lever to position P. Allow the
transmission to cool down. You can
continue your journey, but moderate
your speed and exercise due caution.
Have the system checked if the situa-
tion reoccurs.
Lights up in yellow:
Transmission too hot Avoid high engine loads. You can
continue your journey, but moderate
your speed and exercise due caution.
Selector lever position P not engaged.
Vehicle not prevented from rolling
12Cause What to do
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG
Page 210 of 218
Everything from A to ZREFERENCE
209
Driving stability control systems 76
Driving through water 107
Driving tips, refer to Driving
notes 106
Dry air, refer to Cooling function 98
DSC Dynamic Stability Control 76
DTC Dynamic Traction
Control 77
Dynamic Brake Control DBC, refer to Brake Assist 76
Dynamic Stability Control DSC 76
Dynamic Traction Control
DTC 77
E
Eject button 122
Electrical malfunction
– convertible top 36,42
– door lock 27
– fuel filler flap 140
– tailgate 28
Electric power windows
– initializing 33
Electronic brake-force distribution 76
Electronic Stability Program ESP, refer to Dynamic
Stability Control DSC 76
Emergency operation, refer to Manual operation
– convertible top 36,42
– door lock 27
– fuel filler flap 140
– transmission lock, automatic
transmission 59
Emergency operation, see manual operation
– tailgate 28
Emergency services, refer to Roadside Assistance 177
Emergency unlocking 29
Ending a call 134 Engine
– breaking in
106
– data 196
– overheated, refer to Coolant
temperature 158
– speed 196
– starting, Comfort Access 31
Engine compartment 155
Engine coolant, refer to Coolant 158
Engine oil
– additives, refer to Approved engine oils 157
– alternative oil types 157
– approved engine oils 157
– capacity 157
– checking level 156
– dipstick 156
– intervals between changes,
refer to Service
requirements 71
– MINI Maintenance
System 159
Engine oil level, checking 156
Engine output, refer to Engine
data 196
Engine starting, refer to Starting the engine 56
ESP Electronic Stability Program, refer to Dynamic
Stability Control DSC 76
Exhaust system, refer to Hot exhaust system 107
Exterior mirrors 49
– adjusting 49
– auto
matic heating 50
– folding in and out 49
External audio device 99,116
External care 161
External temperature display
– change units of measure 70
– in the onboard computer 70
Eyes
– for tow-starting and towing away 179
– for tying down loads 111
F
Failure messages, refer to
Check Control 73
Failure of an electrical consumer 176
Fastening safety be lts, refer to
Safety belts 48
Fast forward
– CD 121
Fault messages, refer to Check
Control 73
Filter
– microfilter/activated- charcoal filter for automatic
climate control 98
– microfilter for air conditioner 96
Fine wood, care 164
First aid pouch 177
Fixture for remote control, refer to Ignition lock 55
Flash when locking/ unlocking 25
Flat tire
– run-flat tires 152
– Tire Pressure Monitor TPM 82
Flat Tire Monitor FTM 80
– indicating a flat tire 81
– initializing the system 80
– snow chains 80
– system limits 80
Flat tires, refer to Tire
condition 151
Floor mats, care 164
Fog lamps
– replacing bulb 168,170
Folding roof, refer to Convertible top with
integrated sliding sunroof 34
Footbrake, refer to Braking safely 107
Footwell lamps 92
For your own safety 4
Front airbags 85
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG
Page 213 of 218
REFERENCEEverything from A to Z
212
Manual station search117
Manual transmission 57
Manual washing 162
Master key, refer to Integrated
key/remote control 22
Maximum cooling 97
Maximum speed
– with winter tires 154
Medical assistance, refer to First aid pouch 177
Microfilter
– for air conditioner 96
– for automatic climate
control 98
– MINI Maintenance System 159
Microfilter/activated-charcoal filter
– MINI Maintenance
System 159
Microphone for telephone 14
MINI Internet page 4
MINI Maintenance System 159
Mirror dimming feature 50
Mirrors 49
– exterior mirrors 49
– heating 50
– interior rearview mirror 50
Mobile phone
– adjusting volume 133
– connecting, refer to Mobile phone, pairing 130
– installation location, refer to
Center armrest 100
– pairing 130
– refer to Telephone 100
– What to do if…. 132
Mobility Kit 171
Modifications, technical, refer
to For your own safety 4
Monitoring syst em for tire
pressures, refer to Flat Tire
Monitor 80
MP3 121
Multifunctional steering
wheel, refer to Buttons on
the steering wheel 11Multifunction switch
– refer to Turn signals/
headlamp flasher 60
– refer to Wiper system 61
Music tracks
– playing a track 122
– random order 121
N
Neck support, refer to Head
restraints 47
Nets, refer to Storage
compartments 100
New tires 153
Number of cylinders, refer to
Engine data 196
Number of safety belts 45
Nylon rope, refer to Tow
rope 180
O
OBD socket, refer to Socket for
On-Board Diagnosis 160
Octane ratings, refer to Fuel specifications 141
Odometer 66
Oil, refer to Engine oil 156
Oil consumption 156
Oil level 156
Oil types 157
Old batteries, refer to
Disposal 176
Opening and closing
– Comfort Access 31
– from inside 27
– from outside 23
– using the door lock 26
– using the remote control 24
Opening and unlocking
– from inside 27
Outlets
– refer to Air vents 94
– refer to Ventilation 98
Output, refer to Engine data 196 Outside-air mode
– automatic climate control
97
Overheated engine, refer to Coolant temperature 158
P
Paintwork, care163
Park Distance Control PDC 75
Parking
– vehicle 56
Parking aid, refer to Park Distance Control PDC 75
Parking brake 57
Parking lamps, replacing bulb 168
Parking lamps/low beams 88
Parts and accessories, see Vehicle equipment 4
Pathway lighting 89
PDC
– volume 116
Personal Profile 22
Phone numbers
– dialing 134
Plastic parts, care 164
Playing a track, scan
– CD 122
Pollen
– refer to Microfilter/activated- charcoal filter for automatic
climate control 98
– refer to Microfilter for air
conditioner 96
Power convertible top 34
Power failure 176
Power windows 33
Power windows, refer to Windows 33
Pressure, tires 143
Pressure moni toring, tires80
– Flat Tire Monitor 80
Pressure monitori ng of tires,
refer to Tire Pressure Monitor
TPM 82
PTY 119
Puncture
– Flat Tire Monitor 80
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG