wheel bolts MINI Coupe 2012 Owner's Manual
[x] Cancel search | Manufacturer: MINI, Model Year: 2012, Model line: Coupe, Model: MINI Coupe 2012Pages: 218, PDF Size: 3.84 MB
Page 174 of 218
Replacing componentsMOBILITY
173
If the tire cannot maintain the inflation
pressure, drive the vehicle again, refer to
Distributing the sealan t. Then repeat steps
1to4.
If an inflation pressure of 1.8 bar/26 psi still
cannot be reached, then the tire is too heavily
damaged. Contact your nearest MINI dealer. <
Driving on
Do not exceed the permitted maximum
speed of 50 mph/80 km/h; doing so may
result in an accident. <
Replace the defective tire as soon as possible
and have the new wheel/tire assembly
balanced.
Have the Mobility Kit refilled.
Changing wheels
Run-flat tires
Tire change for run-flat tires:
> Prepare for tire change, page 174
> Jack up vehicle, page 174
> Tighten lug bolts, page 175
Space-saver spare tire
Tire change with space-saver spare tire:
>Remove the space-saver spare tire,
page 173
> Prepare for tire change, page 174
> Jack up vehicle, page 174
> Mount space-saver spare tire, page 175
> Tighten lug bolts, page 175
> Drive with space-saver spare tire, page 174
Removing the space-saver spare tire
The screw connection of the space-saver spare
tire is under the floor mat in the cargo area, on
the base of the storage compartment for the tire
change set. 1.
Unscrew the screw connection with the
special wrench.
2. Take out the cover panel.
3. Screw the lifting handle from the toolkit onto
the thread.
4. Raise the lifting handle slightly.
5. Squeeze the securing spring.
6. The space-saver spare tire is released and
must be held by the lifting handle.
7. Lower the space-saver spare tire with the
lifting handle.
8. Unscrew the lifting handle.
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG
Page 175 of 218
MOBILITYReplacing components
174
9.Pull the space-saver spare tire underneath
the vehicle out toward the rear.
10. Position the space-save r spare tire with the
valve facing upward.
11. Unscrew the valve extension from the valve
of the space-saver spare tire.
12. Unscrew the dust cap from the extension
and place it on the valve of the space-saver
spare tire.
Due to its different dimensions, the
damaged wheel cannot be placed in the
recess for the space-saver spare tire. <
Driving with the space-saver spare tire
Drive cautiously and do not exceed a
speed of 50 mph/80 km/h. Changes may
occur in vehicle handling such as lower track
stability during braking, longer braking dis-
tances and changes in self-steering properties
when close to the handling limit. These proper-
ties are more noticeable with winter tires. <
Only one space-saver spare tire may be
mounted at one time. Mount a wheel and
tire of the original size as soon as possible, to
avoid any safety risks. <
Check the tire inflat ion pressure at the
earliest opportunity an d correct it if neces-
sary. Replace the defective tire as soon as possi-
ble and have the new wheel/tire assembly bal-
anced. <
Preparing for a tire change
Observe the safety precautions regarding
flat tires on page 170.< Additional safety measures when
changing tires:
Only change the tire wh en parked on a surface
that is level, firm and not slippery.
The vehicle or the jack could slip sideways on
soft or slippery support surfaces, such as snow,
ice, flagstones, etc.
Do not use a wooden block or similar object as a
support base for the jack, as this would prevent
it from extending to its full support height and
reduce its load-carrying capacity.
Do not lie under the vehicle or start the engine
when the vehicle is supported by the jack; other-
wise, there is a risk of fatal injury. <
1. Place the foldable chock behind the front
wheel on the other side of the vehicle or in
front of the wheel if the vehicle is on an
incline. If the wheel is changed on a surface
with a more severe sl ope, take additional
precautions to secure the vehicle from
rolling.
2. Uncover the lug bolts if necessary.
3. Loosen the lug bolts by a half turn.
Jacking up the vehicle
The vehicle jack is designed for changing
wheels only. Do not attempt to raise
another vehicle model with it or to raise any load
of any kind. To do so could cause accidents and
personal injury. <
1. Place the jack at the jacking point closest to
the wheel.
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG
Page 176 of 218
Replacing componentsMOBILITY
175
The jack base must be perpendicular to the
surface beneath the jacking point.
2. During jacking up, insert the jack head in the
square recess of the jacking point.
3. Jack the vehicle up until the wheel you are
changing is raised off the ground.
Mounting the space-saver spare tire
1.Unscrew the lug bolts and remove the
wheel.
2. Remove accumulations of mud or dirt from
the mounting surfaces of the wheel and
hub. Clean the lug bolts.
3. Lift the new wheel into place.
4. Screw at least two lug bolts finger-tight into
opposite bolt holes.
5. Screw in the remaining bolts.
6. Tighten all the lug bolts firmly in a diagonal
pattern.
7. Lower the vehicle.
8. Remove the jack.
Tightening the lug bolts
Tighten the lug bolts in a diagonal pattern.
Immediately have the wheels checked
with a calibrated torque wrench to ensure
that the lug bolts are firmly seated. Otherwise,
incorrectly tightened lug bolts can present a
safety hazard. <
Tightening torque: 103.3 lb ft or 140 Nm.
Replace the defective tire as soon as possible
and have the new wheel/tire assembly
balanced.
Vehicle battery
Maintenance
The battery is maintenance-free; that is, the
electrolyte will last for the life of the battery
when the vehicle is operated in a temperate
climate.
Battery replacement
Only use vehicle batteries that have been
approved for your vehicle by the manu-
facturer; otherwise, the vehicle could be
damaged and systems or functions may not
be fully available. <
After a battery replacement, have the battery
registered on the vehicle by your MINI dealer to
ensure that all convenie nce functions are fully
available and, if nece ssary, the corresponding
Check Control messages are no longer dis-
played.
Charging the battery
Note
Do not connect battery chargers to the
sockets installed in the vehicle at the
factory; otherwise you may cause damage to
the battery. <
Only charge the battery in the vehicle when
the engine is off. Connections, refer to Jump-
starting on page 177.
General information
To guarantee the full service life of the battery,
ensure that the battery is always properly
charged.
It may be necessary to charge the battery in the
following situations:
>If frequent short trips are taken.
> If the vehicle is frequently parked for more
than a month.
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG
Page 216 of 218
Everything from A to ZREFERENCE
215
T
Tachometer65
Tailgate 28
– Comfort Access 32
– emergency operation 29
– emergency unlocking 29
– manually releasing 28
– opening/closing 28
– opening from outside 28
– unlocking with remote control 26
Tail lamp, refer to Tail
lamps 169
– replacing bulb 169
Tail lamps 169
Tank volume, refer to Capacities 205
Technical data 196
Technical modifications 4
Telephone 128
– hands-free system 136
– installation location, refer to Center armrest 100
Temperature display
– setting the units 70
Temperature of coolant, refer to Coolant temperature 158
Temperature setting
– air conditioner 95
– automatic climate control 97
Tempomat, refer to Cruise control 63
Tensioning straps, refer to Securing cargo 111
Third brake lamp, refer to
Center brake lamp 170
Three-point safety belt 48
Tightening the lug bolts
– keys 165
– torque 175
Tightening torque, refer to
Tightening lug bolts 175
Time
– setting 117
Tire change set
– space-saver spare tire 165Tire failure
– Flat Tire Monitor
81
– indicator/warning lamp 81
– MINI Mobility Kit 171
– run-flat tires 81
– space-saver spare tire 173
– Tire Pressure Monitor 82
Tire inflation pressure 143
– loss 81
– space-saver spare tire 143
Tire pressure mo nitoring, refer
to Flat Tire Monitor 80
Tire Pressure Monitor TPM 82
– limitations of system 82
–
resetting system 82
– warning lamp 83
Tire Quality Grading 150
Tires
– age 152
– breaking in 106
– changing, refe r to Changing
wheels 173
– condition 151
– damage 151,152
– inflation pressure 143
– inflation pressure loss 83
– minimum tread depth 151
– new tires 153
– pressure monitoring, refer to Flat Tire Monitor 80
– pressure monitoring, refer to Tire Pressure Monitor
TPM 82
– puncture 81
– size 150
– wear indicators, refer to
Minimum tread depth 152
– winter tires 153
– with emergency operation
properties 152
Tires with emergency operation properties, refer to
Run-flat tires 152
Tires with safety features, refer
to Run-flat tires 152
Tone
– middle setting 117 Toolkit
165
Tools, refer to Toolkit 165
Torque 196
– lug bolts 175
Tow bar 179
Tow fitting 179
– screw thread 179
Tow fittings for tow-starting and towing away 179
Towing 178
– car with automatic transmission 179
– methods 179
Tow rope 180
Tow-starting 178
TPM, refer to Tire Pressure
Monitor 82
Track width, refer to Dimension 197
Traction control, refer to
– Dynamic Stability Control DSC 76
Trailer operation
– trailer loads and gross vehicle weight 203
Transmission
– automatic transmission with
Steptron
ic57
– manual transmission 57
– overriding selector lever lock
for automatic transmission
with Steptronic 59
Transporting children safely 51
Transport securing devices, refer to Securing cargo 111
Tread depth, refer to Minimum
tire tread 151
"TRIP" 71
Trip-distance counter, refer to
Trip odometer 66
Triple turn signal activation 60
Trip odometer 66
Trunk, refer to Luggage compartment in the MINI
Convertible 109
Turning circle, refer to Dimensions 197
Online Edition for Part no. 01 40 2 914 786 - \251 07/12 BMW AG