headlights MITSUBISHI 3000GT 1992 2.G User Guide

Downloaded from www.Manualslib.com manuals search engine 54-108
CHASSIS ELECTRICAL - Lighting System
1 ‘-‘FE%!oooou2394
Y18AOO61
RELAY
INSPECTIONHEADLIGHT RELAY
/ TAILLIGHT RELAY / FOG LIGHT
RELAY CHECK
Connect battery to terminal 1 and check continuity between
terminals with terminal 3 grounded.
Power is supplied4-5 terminals
Continuity
Power is not supplied4-5 terminalsNo continuity
1-3 terminals
Continuity
POP-UP MOTOR RELAY (Up to 1993 models) CHECK
Check for continuity between terminals under the conditions
described below.
LIGHT AUTOMATIC SHUT-OFF UNIT CHECK
(1) Remove the quarter trim. (Refer to GROUP 52A - Trim.)
(2) Keeping the connector connected to the light automatic
shut-OFF unit, connect the test light (12 V-3.4 W) from
the harness side to terminal No. 6 (for tail lights) or No.
7 (for headlights). Under the following conditions, checkthe operation of the test light.
id
/ TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Theft-alarm System54-223
Trouble symptom
Cause
Check method
Remedy
There is no alarm when, as analarm test, the hood is openedDamaged or disconnected
wiring of hood switch input
If input checks
Repairthe harness or re-
from within the vehicle.circuit.
(P.54-220) indicate aplace the hood switch.
(The alarm is activated, however,malfunction, check by
I
by opening a door or the liftgate.)using check chartMalfunction of the hood p.54-225.
switch.
Malfunction of the ECU.
-Replace the ECU.
Engine would not start [EngineThere is a short-circuit of
starting is possible when the the starter relay activationCheck by using check
chart P.54-234.
Repair the harness.
starter relay is in the switched-off
circuit
(normally closed) condition, with
the clutch switch in the switch-off
and the ECU harness connector
disconnected.]
When, as a test of the alarm, aDamaged or disconnectedCheck by using check
door or the
liftgate is opened wiring of headlight power chart P.54-231, 232.
Repairthe harness or re-
without using the key, orthe hood
is opened from within the vehicle,supply circuit or headlightplace the diode Ds.
activation circuitReplace the headlight
the horn and the theft-alarm hornrelay or the headlight.sound but the headlights don’t
flash. (The headlights can, how-
ever, be switched. ON by usingMa
lfunction of the ECUReplace the ECU.
the passing switch.)The headlights flash during an
alarm test but the horn orthe theftDamaged or disconnectedCheck by using checkRepair the harness.
alarm horn does not sound.wiring of horn relay power
chart P.54-229,230,231.supply circuit or horn ac-Replace the horn.
tivation circuitReplace dedicated fuse
Damaged or disconnectedNo. (6) or the fusible linkwiring of the theft-alarmNo. (6).horn relay power supply
circuit or the theft-alarm
horn activation circuit.
Malfunction of the ECU.
Replace the ECU.The system is not deactivated
nhen, during an alarm test in
Damaged or disconnected
If input checks
which the alarm is intentionallywiring of door key cylinder
Repair the harness.activated, the door or
liftgate isand
liftgate unlock switch(P.54-220) indicate a
input circuitmalfunction, check byReplace the key cylinder
Jnlocked by using the key.
using check chartswitch or the
liftgate
switch.
:The system also cannot be dis-P.54-227,228.
armed.)
Malfunction of door keycyl-inder and liftgate unlock
switch.
Malfunction of the ECU
Replace the ECU.
ECU: Electronic Control Unit
NOTEIf the
lifigate unlock switch or door key cylinder unlock switch is operated roughly, or if these switches have
been installed incorrectly or switches themselves are defective the ECU may not accept the warning or alarmcancelling signal. In such case, the alarm operation will take place when the door is opened using a key.
[When the door key cylinder switch has been shorted, however, if the ignition switch is turned ON, the ECU
judges the detection-switch as faulty and thereafter, it will prevent setting of (warning) alarm until the shorting
is corrected.]
If the
liftgate is opened using a key and is left opened when the door key cylinder switch system has a trouble
(wiring harness damage, open circuit, etc.), the ECU judges it as the
liftgate holding mode and does not producealarm even when the door is opened.
TSB Revision