engine MITSUBISHI 3000GT 1992 2.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Lighting System54-95 1
COLUMN SWITCH
!$;fyi$IGNALi
(G-l
iD-45)
(G-Z
(D-04:
0.85G-1
0.85G-L
(c-02)
0.85G-L
E
2B
(D-41)
-cAL
“‘t
I
0
I
f
;
,
nz
2E
;4
"i;!,5-
0.8:
G-F
0.
8FG-I;-_-___
0.85
LG-R
0.85LG-R
19
0.85G-L
I-
3
=A
wREARCOMBINATION B4LIGHTCLH)
(F-30) 2B
d=
q
0.85G-F
0.85GR-R
30(F-19)(F-30)HROSM02AB
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-96CHASSIS ELECTRICAL - Lighting System
CIRCUIT DIAGRAM (FROM 1995 MODELS)
IGNITIONSWITCH(IG?)BATTERY;&IGHT
2B-W1.25R-W
0DEDICATED
FUSE
15ACHARGING2B-wL
,,7 :c-82)0.85R-B lG-W 6 (c-69)/\J’BI mo
-___----____/\I\
B-W
f-
D-44)% ---- :T2 ------ -$~e---m--.~s---:~8%I I&
Og;G-WA&n
*3> “$2“i;“=!0.85
0. 85G-RI
B-WG-W
I/x5 .\7A10e9 x.3wmj,\. p!&'
OFF-c. ON
lOFF--. ON5 loF1;F-~oN m'R% thnrnnnb
G-W
1. .----iND
- - v.85G-L
0.85G-R
2 cc/ I.
E(D-06)IOX
'E%T'~~~J~~SPECTION
.REAR WINDOWDEFOGGERE#@;.NIC
SUSPENSIONzl
A
o,d3°gt12
B
\y---- --------
:c-?:,jE p2w
*\L &I--
a-7j% 166
“$ZI0.85G-W
G-RI I2 CL
& &I I
I
0.8%-(
(D-41)
38
I
0.85G-06
1:s; (D-43)RHEObAT0.85G-Y
qIt.CHARGING0.85G-C.MFI SYSTEM.COOLING+&$&ANDI.WARNING LIGHT
28
TURN SIGNAL
AND HAZARD
FLASHER UNIT
(E-30)
NOTEx1:1995 MODELSX2:FROM 1996 MODELS
HR09M03AA
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Lighting System54-97
COLUMN SWITCH
iCARBURETTOR
ASSEMBLY1
(G-L(LG-E
0.85G-L
0.85G-L
(c-02)
0.85G-L
L-----_
(LG-R
;5
2B
(D-41)
2E13
101m
I)
34
1. 2(A-39) B\P
,4
2B
nz
0.8EG-F
0.85G-R
------
0.85
LG-R
0.85G-L0.85G-f
,J3--------------19
0.85G-Lx10.85GR-IGR-L*2
r-y3I /
wCOMBINATION B4LIGHT (LH)
(F-30) 2B
!
1
COMBINATION
12m
3
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-98CHASSIS ELECTRICAL - Lighting System
STOP LIGHT
CIRCUIT DIAGRAM L)
FUSIBLE LINK@
0.85R-B ‘7 (c-83)
WITHE;$FiEFUISEIWITHOUT
_AUTO-CRUISE
CONTROL
t.MFI SYSTEM. &&~EU'SE
(c-61)(c-62)
0.85G
0.85G
0
2B
h=
0.85G
!
HIGH MOUNTED BSTOP LIGHT
m
2B
0.85G5(F-'iS)
t
0.85G3mG42
0.85G
I
i-ANTI-LOCK BRAKING SYSTEM
2.ELECTRONIC CONTROLSUSPENSIONz3
REAR
COMBINAT
LIGHTCRHION)J
NOTEZ'l:VEHICLES WITHOUTACTIVE AERO%E:VEHICLES WITHACTIVE AERO%3:UP TO 1995 MODELS
(c-61) (c-62) (C-68) ET3)(F-04)‘l(F-04)%2 (F-10) (F-19)
@J @ fl pggq& pFtiqw[m~a-~~
HROSMO4AA
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Lighting System
CIRCUIT DIAGRAM
54-99~
LINK@
FUSIBLE,
i
REARCOMBINATIONLIGHTCLH)G
AY
o-85x 140
0.85Gt
IJ
40
B
!
2B-
+.MFI SYSTEM'#T&cpsF
. ANTI-LOCKBRAKING SYSTEM.ELECTRONIC CONTROLSUSPENSION:
NOTEx:1995 MODELS
(lxn (c-621 (C-68) (c-83)
@Q pJ ~~~~~~1
-
1
4(F-10)
B
2B
q
REAR
COMBINATION
LIGHTCRH)
HROSM05AA
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-100CHASSIS ELECTRICAL - Lighting System
Unit A:Must be
used at
rear tire
“..“I. .other
Unit B:Must be used
at front tire1 -216802451.Calibration fixture2. Thumb adjusting screws
3.Level vial
4. Floor level offset dial
5. Horizontal dial knob
6. Vertical dial knob
7. Aimer level vial
8. Level vial bubble
9. Top port hole
10.Viewing portON-VEHICLE
SERVICE
HEADLIGHT AIMING
PRE-AIMING INSTRUCTIONS
(Up to 1993 models)
1. Test dimmer switch operation.
2. Observe operation of high beam light mounted in instru-
ment cluster.3. Inspect for badly rusted or faulty headlight assemblies.
These conditions must be corrected before a satisfactory
adjustment can be made.4. Place vehicle on a level floor.
5. Bounce front suspension through three (3) oscillations
by applying body weight to hood or bumper.6. Inspect tire inflation.
7.Rock vehicle sideways to allow vehicle to assume its nor-
mal position.
8.If fuel tank is not full, place a weight in trunk of vehicle
9.
to simulate weight of a full tank [3 kg (6.5 Ibs.) per gallon].
There should be no other load in the vehicle other than
driver or substituted weight of approximately 70 kg (150
Ibs.) placed in driver’s position.
10. Thoroughly clean headlight lenses.
11. Adjust headlights following the instructions of the headlight
tester manufacturer.
(From 1994 models)1. Inspect for badly rusted or faulty headlight assemblies.
These conditions must be corrected before a satisfactory
adjustment can be made.2. Place vehicle on a level floor.
3. Bounce front suspension through three (3) oscillations
by applying body weight to hood or bumper.
4. Inspect tire inflation.
5.Rock vehicle sideways to allow vehicle to assume it.snor-
mal position.
6.If fuel tank is not full, place a weight in trunk of vehicle
7.
to simulate weight of a full tank [3 kg (6.5 Ibs.) per gallon].
There should be no other load in the vehicle other than
driver or substituted weight of approximately 70 kg (150
Ibs.) placed in driver’s position.8. Thoroughly clean headlight lenses.
9. When performing the visual headlight adjustment on ve-
hicles with resin lens headlights, be sure to observe the
following precautions.
CautionWhen adjusting one headlight, the other headlight
should be turned off if possible. If this is not possible,
do not cover the other headlight for more than threeminutes while it is turned on. Otherwise, heat from
the bulb may warp the headlight lens.
NOTE
If the visual headlight adjustment at low beam is made,
the adjustment at high beam is not necessary.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Lighting System54-101
VERTICAL ADJUSTING
Adjust the vertical angle with the vertical adjusting gear sothat the bubble of the vertical angle gauge is aligned with
the “0” mark position.
NOTEThe beam angle will change about 0’12’ with on mark.
Stopper
Center bm
Vertical angle gauge
HORIZONTAL ADJUSTING
Insert a screwdriver in the horizontal adjusting hole and turnuntil the
“0” mark and the center line are in alignment.
NOTEThe beam angle will change about 0’23’ with on mark.
Gear (6)“0” hark
3.Check to see that the bubble in the headlight vertical angle
gauge is in the illustrated position.
4.If the bubble is out of position, adjust by turning the adjust-
ing screw.
5.Confirm that the “0” mark on the headlight horizontal angle
adjusting gear (B) is in alignment with the center line.6. If not, perform the adjustment as follows.
(1) Pull up the stopper.
(2) Push the gear (B) in the arrow direction to disengage
it from the gear (A).(3) Align the “0” mark on the gear (B) with the center
line.
(4) Push down the stopper to engage the gear (B) with
the gear (A).
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Lighting System
Up to 1993 modelsFrom 1994 mod&
__ _..--.
Vertical center lineZ16FO509
JHot
z&ky M-j’ Within~ Within600mm1mm (in.)600 mm
(23.6)
(23.6)
Note l ’ Up to 1993 modelsl 2 From 1994 models
1 Etomj
0000236600002387
LUMINOUS INTENSITY MEASUREMENT
Measure the luminous intensity of headlights with a photo-me-ter in accordance with the instruction manual prepared by
the manufacturer of the photometer and make sure that the
luminous intensity is within the following limit.Limit: 20,000 cd or more
NOTE
(1) When measuring the luminous intensity of headlight, keepthe engine at 2,000 rpm and have the battery charged.
(2) If there are specific regulations for luminous intensity ofheadlights in the region where the vehicle is operated,
make sure that the intensity conforms to the requirements
of such regulations.
FOG LIGHT AIMING
1.Place vehicle on a known level floor 7.6 m (25 feet) from
aiming screen or light colored wall.
2. Use adjusting screw to adjust the top end of high intensity
zone to dimension A.
BULB REPLACEMENT
1. Disconnect the connector.
2. Turn the bulb socket counterclockwise to pull it out.
Caution
Do not touch the surface of the headlight bulb with handsor dirty gloves. If the surface dies become dirty, clean
it with alcohol or thinner, and let it dry thoroughly before
installing.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine HEADLIGHT
CHASSIS ELECTRICAL - Lighting System54-103
REMOVAL AND INSTALLATION
(From 1994 models)
(Up to 1993 models)
Removal steps (From 1994 models)
1. Front combination light
2. Headlight
4Bb
4WFOOB100002389
Removal steps (Up to 1993 models)
1. Headlight bezel, upper
2. Headlight bezel, lower
3.Retaining ring4.Headlight5.Spring6.Mounting ring7.Housing8.Rod assembly9.Headlight hood
10.Link assembly11. Boot12. Pop-up motor
REMOVAL SERVICE POINTS
+A, HEADLIGHT BEZEL, UPPER REMOVAL(1) Raise the headlights by using the pop-up switch.
Disconnect the negative (-) battery terminal.(2) Remove the headlight bezel, upper.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Lighting System
16A0833
A(Conductivity
Headlight lower
stop position
16FO17100002390
+B, ROD ASSEMBLY REMOVALUsing a flat head screwdriver (wrap cloth or similar on
the ball joint area to prevent injury), disconnect the connec-
tor.NOTE
When disconnecting the rod assembly from the link, hold
the link by hand.
INSPECTION
POP-UP MOTOR (Up lo 1993 models) CHECKRotate the manual knob of the pop-up motor clockwise by
hand to check continuity between terminals.
TerminalWhen the
(+) terminal of the B
ohmmeter is connected to (1)
and the (-) terminal is connected
to (2)
Continuity rangeWhen the
(+) terminal of the A
ohmmeter is connected to (1)
and the (-) terminal is connected
to (5)
‘1 I
Lj
I
‘d ~~
iji
TSB Revision