doors MITSUBISHI 3000GT 1993 2.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 208CIRCUIT DIAGRAMS - Buzzer Circuit
BUZZER CIRCUIT (UP TO 1993 MODELS)
E LINK@IGNITION SWITCH(IG1)
I120-w
0
15A
‘(c-82)
1
J/B
FUSIE
5W-B(c-68)
(c-70)
R
r
V
1 "20.85R-B 3m
I
B-W
R-B
n'---- BUZZER-(n-??'i IOD OR
STORAGE
CONNECTOR
WHEN
IS RE(A-11X)
-\y
2
Y-W
1
4-d
B-W DIODE
C-08II JY-R
\I
Y-B 3
DOORSWITCH (LH)
:'l:VEHICLES WITHOUTTHEFT-ALARM SYSTEM=:2:VEHICLES WITHTHEFT-ALARM SYSTEM
(A-11X) (c-58) (c-65)*1
HR15M03AA
1 TSB RevisionI

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Central Door Locking Circuit235
FUSIBLE LINK0
R-B
1(c-66) 51ETACS UNIT(c-65)4
Inhn""YI
STORAGE
CONNECTOR
(A-11X)
(F>R-B
;I;" LIGHT
LUGGAGE
COMPARTMENT
LIGHT
GNDn
i
--254j7:4jg $5
G-Y
B
(F)
----_6:5
R-G
R-G
4:4
R-G 1
ir
---OFFOFF - ON - ON
1
G-Y.J
I
G-YD
II=
GND GND
kxmJ77~oB B
KEY REMINDER
SWITCH
Bw&BSTHEFT-ALARM
(c-58) B5 4
"v vj2B
LINKXTORA DATACONNI
DOORSWITCH (LH)
lM07BB
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Central Door Locking Circuit237
OPERATION/
Li!l
When the door lock switch is set to the LOCKside (or UNLOCK side), the LOCK side (or
UNLOCK side) of the door lock relay is turned
ON and the door actuators of all doors operate.l
If the driver seat side door (or assistant seat
side door) is opened and the driver seat side
inside lock knob (or assistant seat side inside

0
,’
id
0
With the driver’s and front passenger’s doorsunlocked, press the LOCK switch of the
transmitter, and the door lock signal output (0V) will be sent from the
keyless entry control
unit terminal No. 12 closing the door lock powerrelays 1 and 2 to lock the driver’s and front
passenger’s doors.
While the R.H. and L.H. doors are in the lockedstate, press the UNLOCK switch of the
transmitter once, and the DOOR UNLOCK
switch signal (0 V) will be sent from the keylessentry control unit terminal No. 14 closing the
door lock power relay 2 to unlock the driver’s
door.
Under the above-mentioned conditions, further
press the UNLOCK switch of the transmitter,and the DOOR UNLOCK signal output (0 V)
will be sent from the keyless entry control unitterminal No. 13 closing the door lock power
relay 1 to lock the front passenger’s door.
When the keyless entry system is operated toturn the driver’s door lock switch from the
UNLOCK position to the LOCK position, thelock knob) is locked with the key inserted in
the ignition switch, the ETACS unit grounds the
unlock side circuit of the door lock relay to unlock
all doors. This way, failure to remove the key
is prevented.dome light/foot light blinking signal output
(system voltage) will be sent twice from the
keyless entry control unit terminal No. 11 when
the door lock switch is turned from the LOCK
position to the UNLOCK position, the lighting
signal output (0 V) will be provided for approx.
3 seconds.
NOTE
The dome light winks or comes on when the domelight switch is in the DOOR interlock position.
However, the dome light does not wink while it .is
ON for 6 seconds after closing the door by ETACS
function.Besides the above-mentioned operations, the
keyless entry control unit has the following functions.l
If any door is not opened or closed within 30
seconds from unlocking the door by means ofthe
keyless entry system, the door is
automatically locked.In addition, if the
cryptographic code other than the code storedin the receiver memory is received 30 times
in one minute continuously, operation of the
unit is suspended for 10 minutes.l
Operation is also suspended if the ignition key
remains inserted (key reminder switch: OFF)
and either door is left open (door switch: ON).TROUBLESHOOTING HINTS

Phenomenon
Inspection method
One of the door lock actuators fails to operate.
0Check the door actuator which fails to operate.
No unlock operation can be made by pressing door lock0
knob after fulfilment of following conditions.Check the key reminder switch input signal.0Check the key reminder switch. (Refer to GROUP
0Insertion of key in ignition switch (key reminder switch54-Ignition Switch.)
OFF)0
0Opening of door (door switch ON)Check the front door switch input signal.0 Check the front door switch. (Refer to GROUP
42-Door Assembly)
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 238CIRCUIT .DIAGRAMS - Central Door Locking Circuit
l
The indicator does not blink after pressing thetransmission switch of the transmitter.
1) Check or replace the battery. (Refer to
GROUP
42-Keyless Entry System.)
2) Replace the transmitter.
l Transmitted wave is being sent from thel
R.H. and L.H. doors can be locked and unlocked
by the transmitter but the dome light and footlight do not blink or come on. (Interlocked
lighting of the dome light and foot light by means
of the dome light switch or door opening and
closing is normal).
transmitter (indicator is blinking), but the system
does not operate.1) Check the cryptographic code registering
method. (Refer to GROUP
42-Keyless
Entry System.)
2)Check the keyless entry control unit terminalvoltage. (Refer to GROUP
42-Trouble-
shooting.)3) Check the coaxial cable of antenna and
the ground wire for connection.
l Only R.H. or L.H. door can be locked or
unlocked.
1)Check the door lock power relay 1 (for front
passenger’s door) or door lock power relay2 (for driver’s door). (Refer to GROUP
42-Central Door Locking System.)
2)Check the keyless entry control unit terminalvoltage. (Refer to GROUP
42-Trouble-
shooting.)
1)Check the keyless entry control unit terminal
voltage (Refer to GROUP
42-Troubleshoot-
ing.)2) Check the harness.
NOTE
l :Perform this check when replacement of the
transmitter and/or
keyless entry control unit or
faulty storage of cryptographic code has been
made.
\
Ilj
‘d I
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-78CHASSIS ELECTRICAL - Lighting System
OPERATION light>l
Battery voltage is always applied to the dome light. When the dome light switch is turned to “ON”,
the dome light will remain lit. After either door is opened if the dome light switch is at “DOOR” position,the dome light will come on.
lWith the dome light turned on (with the ignition switch in the OFF position and with the dome light
switch in the DOOR position), close all doors, and the timer circuit in the ETACS unit will be activatedto gradually vary the voltage for approx. 6 seconds owing to the duty control, and the voltage will
be output to transistor Tr. Since the voltage applied to the dome light gradually decreases, the dome
light will be dimmed.lIf the ignition switch is turned to “ON” while the dome light is lit (while the timer is activated), the
timer circuit will be opened to turn “OFF” transistor Tr. This will immediately turn off the dome light
without dimming. light>-lBattery voltage is always applied to the foot lights and ignition key illumination light.
With the ignition switch in the OFF position, open any door, and all lights will come on.
l
With all lights turned on (with the ignition switch in the OFF position), close all doors, and the timercircuit inside the ETACS unit will operate in the same manner as the dome light to dim all lights.
When the ignition switch is placed in the ON position with all lights turned on (with the timer in operation),the same operation as the dome light will take place.
TROUBLESHOOTING HINTS
Phenomenon
Dome light does not come on
when
a door is opened with the
dome light switch in the DOOR
position.
Check the door switch input signal.
Check the door switch. (Refer to GROUP 42 -
The foot lights and ignitionl
key cylinder illumination
Check the dome light switch.
light illuminate.
lCheck the dome light bulb.
Dome light, foot lights and ignition key illumination light go out
l
at once when doors are closed.Check the door switch input signal.(Refer to P.54-80.)Even if ignition switch is turned on while lights are being
l
dimmed,lightsdo notout at the same time.
Check the ignition switch input signal.
go
(Refer toP.54-80.)
COMPONENT LOCATION
Data ‘link
connect&
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-210CHASSIS ELECTRICAL - Theft-alarm System
CIRCUIT DIAGRAM
FUSIBLE LINK@IGNITIONI
2B-
(I
(
L)
3,t
Q
2)(I
@
i10
c-7’
Ob”
I
x
ObS
AAL,
D
'G0
DZ8
t
z
5
1
'ITCH(IG1)IGNITION SWITCH(ACC)
7_ ------ - ---- Tjj-
-l
0
15A@
15A
2R-B
FOG LIGHT
5TAILLIGHT.bARKING/
SIDE MARKER
LIGHT AND
b;gXySE PLATE
HEAD
LIGHT
RELAY
(A-O1X)16 (c-80)------____3
1
1
WITHOUTWITHACCESSORY ACCESS
SoCKET
0.85L
L 0.85LI--L
CIGARETTE
LIGHTER
\
>)
I
(R-Y‘3D-r2R-L;ORY
B-h
----IBACK-UP LIGHT
3-w
1B-W
RADIO ANDTAPE PLAYER
rFOG
LIGHT
3
>
1
(R-Y
0.85BI
@” L1GHTJGGAGEiyi;tRTMENT
(c-ol)&---------- ____ ,F
0.85B0.85R
* e8
2B,,3 (c-76)J/B'
A
\/ _
3 (c-82)28
n=
(R-Y)
HEADLIGHT
lO(c-65)
(R-Y(I
R-G
I8
Vk
i
LIGHT
AUTOMATIC
SHUT-OFF
UNIT
- -- -= =
(LH)(RH)\*/
DOORSWITCH
2hJ
5(E-17)._i
Y-B56
A
HRlJMOlAA
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-222CHASSIS ELECTRICAL - Theft-alarm System
TROUBLESHOOTING QUICK-REFERENCE TABLE
For information concerning the locations of electrical components, refer to GENERAL-Theft-alarm System
Circuit.
1.ARMING / DISARMING RELATIONSHIP
Trouble symptomThe system is not armed (The
SECURITY light doesn’t illumi-
nate, and the alarm doesn’t func-
tion.)
(The central door locking system
functions normally.
If the central locking system doesnot function normally, refer to
GROUP 42.)
The arming procedures are fol-
lowed, but the SECURITY light
does not illuminate.(There is an alarm, however,
when an alarm test is conductedafter about 20 seconds have
passed.)
The alarm sounds in error when,
while the system is armed, a door
or the liftgate is unlocked by us-
ing the key.
ICause
Damaged or disconnected
wiring of ECU power sup-
ply circuit
Damaged or disconnected
wiring of door switch input
circuit
Damaged or disconnectedwiring of SECURITY light
activation circuit.Blown SECURITY light
bulb
Malfunction of the ECU.
Damaged or disconnected
wiring of a door key cylin-
der and the
liftgate unlock
switch input circuit.
Malfunction of a door key
cylinder and the liftgate un-
lock switch.
Malfunction of the ECU.
2.ACTIVATION / DEACTIVATION RELATIONSHIP
Trouble symptomCauseThere is no alarm when, as an
Damaged or disconnected
alarm test, a door is opened with-wiring of door switch (all
out using the key.doors) input circuit
(The arming and disarming arenormal, and the alarm is
acti-Malfunction of the door
vated when the liftgate or hood isswitch
opened.)
Malfunction of the ECUThere is no alarm when, as an
Damaged or disconnected
alarm test, the liftgate is opened
without using the key.wiring of liftgate switch in-
put circuit
(The alarm is activated, however,
by opening a door or the hood.)Malfunction of the liftgate
switch.
Malfunction of the ECU.Check methodCheck by using check
chart P.54-224.Check by using check
chart P.54-225.Check by using check
chart P.54-229.
If input checks
(P.54-220) indicate amalfunction, check by
using check chart
P&f-227.
Check method
If input checks
(P.54-220) indicate a
malfunction, check by
using check chart
P.54-225.
If input checks
(P.54-220) indicate a
malfunction, check by
using check chart
P.54-228.
Remedy
Replace the fusible link
No. (6) or the fuse No.
(19).Repair the harness.
Repair the harness or re-
place the door switch.
Replace the fusible linkNo. (6) or the fuse No.(1%
Repair the harness.
Replace the bulb.
Replace the ECU.
Repair the harness or re-
place a door key cylinderand the
liftgate unlock
switch.
Replace the ECU.
Remedy
Repairthe harness or re-
place the door switch.
Replace the ECU.
Repair the harness or re-
place the liftgate switch.
Replace the ECU.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-226CHASSIS ELECTRICAL - Theft-alarm System
5. DOOR LOCK ACTUATOR SWITCH INPUT CIRCUIT
Description of operation
When a door is locked by the lock knob or the key, the door
lock actuator switch is switched OFF, and HIGH-level signals
are sent to the ECU. These signals activate the timer circuit
of the R ECU, thereby causing the activation circuit to function,thus
R activating the door lock actuator of all doors.
ECU terminal voltage (Connection condition of the ECU con-
nector).
ECU
terminal
No.
13
14
!
I
t
((
Signal
Door lock ac-
tuator switch
(driver door)
loor lock ac-
uator
switch
:passenger
joor)ConditionTerminal
voltage
Door
Lock:5 V’lock ac- OFF
tuator
switchUnlock: ON 0 V
DoorLock:‘5 v*lock ac- OFF
tuator
switchUnlock: ON 0 V
*Measurement is not possible by using a voltmeter, but is possible
by using an oscilloscope.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine iCHASSIS ELECTRICAL
- Theft-alarm System54-229
JS!SECURITYE-04@y&fiNAT! ON .$36
152
FUSIBLE LINK CE)m
z0alz!
r%BECATED
mCL
1
TO THE ECUTO THE HORN8. SECURITY LIGHT ACTIVATION CIRCUIT
Description of operation
If all doors are in locked state after key-less locking, the ECUtransistor is turned ON and the security light comes on.
Checking the security light activation circuit (Disconnect the
connector of the ECU and check at the wiring harness side.)Nor-
malMal-
stepCheck objectcondi-func-
Cause
Remedy
tiontion
1D-04connector12v ovterminal voltage 51Fuse (19) dam-Replaceaged or discon-the fusenetted
Harnessdam-Repair the
aged or discon-harnessnetted, or short-circuit
2D-04connector12v ovterminal voltage 52Damaged or dis-
Replaceconnected wiringthe bulbofSECURITYlight bulb
Harness
dam-Repair the
aged or discon-harnessnetted
3ECU terminal volt-12v ovHarnessdam-
age 57Repair the
aged or discon-harnessnetted, or short-circuit9. HORN RELAY POWER-SUPPLY CIRCUIT
Description of operationPower voltage is always supplied to the horn relay.
Checking the horn relay power-supply circuit (Disconnect the
horn relay)
connector terminal
Mal-func-CauseRemedytion
Fuse (3)
dam-Replace the
aged or discon-fusenetted
Damaged or dis-Repair the har-connected har-nessness
TSB Revision