belt MITSUBISHI 3000GT 1994 2.G Owner's Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1994, Model line: 3000GT, Model: MITSUBISHI 3000GT 1994 2.GPages: 738, PDF Size: 35.06 MB
Page 454 of 738
Downloaded from www.Manualslib.com manuals search engine 16-8ENGINE ELECTRICAL - Charging System
This test determines whether the generator outputs
normal current.(1) Before the test, always be sure to check the
following.l Generator installation
l
Battery (Refer to GROUP 54 - Battery.)
NOTE
The battery to be used should be slightly dis-charged. The load in a fully-charged battery
will be insufficient and the test may not be able
to be carried out correctly.l Generator drive belt tension (Refer to
GROUP 11- On-vehicle Service.)l Fusible link
l Abnormal noise from the generator while
the engine is running(2) Turn the ignition switch to the OFF position.
(3) Disconnect the negative battery cable.
(4) Disconnect the generator output wire from the
generator
“B” terminal and connect a DC testammeter with a range of O-100 A in series
between the “B” terminal and the disconnected
output wire. (Connect the
(+) lead of the amme-ter to the
“B” terminal, and then connect the(-) lead of the ammeter to the disconnected
output wire.)
Caution
Never use clips but tighten bolts and nutsto connect the line.
Otherwise loose
connections (e.g. using clips) will lead to
a serious accident because of high current.
NOTE
A clamp-type ammeter which enables measure-
ments to be taken without disconnecting the
generator output wire is recommended.(5) Connect a voltmeter with a range of 0
- 20
V between the generator “B” terminal and the
ground. (Connect the
(+) lead of the voltmeterto the “B” terminal, and then connect the (-)
lead of the voltmeter to the ground.)
(6) Connect a tachometer. (For the procedure forconnecting the tachometer, refer to GROUP
11 - On-vehicle Service.)
(7) Connect the negative battery cable.
(8) Leave the hood open.(9) Check to be sure that the reading on the
voltmeter is equal to the battery voltage.
NOTE
If the voltage is 0 V, the cause is probably an
open circuit in the wire or fusible link between
the generator “B” terminal and the battery
(+)
terminal.
(1O)After turning the light switch on and turning on
the headlights, start the engine.
(1l)lmmediately after setting the headlights to high
beam and turning the heater blower switch to
the high revolution position, increase the enginespeed to 2,500
r/min and read the maximum
current output value displayed on the ammeter.
Limit value: 70% of nominal current output
NOTEl
For the nominal current output, refer to the
Generator Specifications.l
Because the current from the battery will
soon drop after the engine is started, the
above step should be carried out as quickly
as possible in order to obtain the maximum
current output value.l The current output value will depend on
the electrical load and the temperature of
the generator body.l
If the electrical load is small while testing,the specified level of current may not be
output even though the generator is normal.
In such cases, increase the electrical load
by leaving the headlights turned on for sometime to discharge the battery or by using
the lighting system in another vehicle, and
then test again.l
The specified level of current also may not
be output if the temperature of the generator
body or the ambient temperature is too high.
In such cases, cool the generator and then
test again.
(12)The reading on the ammeter should be above
the limit value. If the reading is below the limit
value and the generator output wire is normal,
remove the generator from the engine and check
the generator.(13)Run the engine at idle speed after the test.
(14)Turn the ignition switch to the OFF position.
(15)Disconnect the negative battery cable.
(16)Disconnect the ammeter, voltmeter and
tachometer.(17)Connect the generator output wire to the
generator “B” terminal.
(18)Connect the negative battery cable.
TSB Revision
Page 455 of 738
Downloaded from www.Manualslib.com manuals search engine ENGINE ELECTRICAL - Charging Svstem16-9REGULATED VOLTAGE TEST
\:
b
Ignitionswitch (IGl)Generator
This test determines whether the voltage regulator
is correctly controlling the generator output voltage.
(1) Always be sure to check the following before
the test.l Generator installation
lCheck to be sure that the battery installedin the vehicle is fully charged. (Refer to
GROUP 54 - Battery.)l Generator drive belt tension (Refer to
GROUP 00 - Maintenance Service.)l Fusible link
l Abnormal noise from the generator while
the engine is running(2) Turn the ignition switch to the OFF position.
(3) Disconnect the negative battery cable.
(4) Connect a digital-type voltmeter between the
generator “S” terminal and the ground. (Connect
the
(+) lead of the voltmeter to the “s” terminal,
and then connect the (-) lead of the voltmeter
to a secure ground or to the battery (-) terminal.)
(5) Disconnect the generator output wire from the
generator
“B” terminal.(6) Connect a DC test ammeter with a range of
O-100A in series between the “B” terminal andthe disconnected output wire. (Connect the
(+) lead of the ammeter to the “B” terminal,
and then connect the (-) lead of the ammeter
to the disconnected output wire.)
(7) Connect a tachometer. (Refer to GROUP 11
- On-vehicle Service.)
(8) Reconnect the negative battery cable.
VOLTAGE REGULATION TABLE
Ammeter
- Load
6EN1029
(9) Turn the ignition switch to the ON position and
check that the reading on the voltmeter is equal
to the battery voltage.
NOTE
If the voltage is 0 V, the cause is probably an
open circuit in the wire or fusible link between
the generator
“S” terminal and the battery (+)
terminal.
(1O)Check to be sure that all lights and accessories
are off.
(11) Start the engine.(12)lncrease the engine speed to 2,500
r/min.
(13)Read the value displayed on the voltmeter when
the current output by the generator becomes
10A or less.
(14)lf the voltage reading conforms to the value
in the voltage regulation table, then the voltage
regulator is operating normally.If the voltage is outside the standard value,
there is a malfunction of the voltage regulator
or of the generator.
(15)After the test, lower the engine speed to the
idle speed.
(16)Turn the ignition switch to the “OFF” position.
(17)Disconnect the negative battery cable.
(18)Disconnect the ammeter, voltmeter and
tachometer.(19)Connect the generator output wire to the
generator “B” terminal.
(20)Connect the negative battery cable.
Inspection
terminal
Terminal “S”
Voltage regula-Standard value Inspection
torambient (V)terminal
temperature
(“C PI)-20 (-4)14.2-15.4
Terminal “S”
20 (68)13.9-14.9
TSB Revision
Voltage regula- Standard value
torambient (V)
temperature(“c
PI)
60 (140)13.4-14.5
80 (176)13.1-14.5
I
Page 458 of 738
Downloaded from www.Manualslib.com manuals search engine 16-12ENGINE ELECTRICAL - Charging System
GENERATORREMOVAL AND INSTALLATION
Pre-removal and Post-installation Operationl Removal and Installation of Right Bank Warm Up
Three-Way Catalytic Converter(Refer to GROUP 15-Exhaust Pipe, Main Mufflerand Catalytic Converter.)14-18ft.lbs.
l b
Removal steps
1. Air hose E
3. Suction hose clamo nuts
(Refer to GROUP 11
-Engine Adjustment.)
216FO346
5. Generator connector
6. Heated oxygen sensor connector
7. Generator and generator bracket
assembly8. Generator bracket
9. Generator
lo-12 Nm7-9 ft.lbs.24 NmREMOVAL SERVICE POINT
dAbCLAMP NUT REMOVAL
On vehicles with an air conditioning, remove the clamp
nut, raise the suction hose and suspend it from the engine
hood using a cord.
1 TSB Revision
Page 491 of 738
Downloaded from www.Manualslib.com manuals search engine ENGINE ELECTRICAL - Ignition System16-45 l
IGNITION SYSTEM
LREMOVAL AND INSTALLATIONI
i
27EN0520
413 NmIlOft.lbs.
d
12 Nm
9 ft.lbs.
22 Nm16ftAbs.B678
W1
,A4
Removal stepsl Intake manifold plenum (Refer to
GROUP
1.5 - Intake Manifold.)1. Center cover
2. Spark plug cable
3. Spark plug
4. Ignition coil
5. Ignition power transistor
6. Crankshaft position sensor
cl 992 models>9 Nm
7
ft.lbs.u 16FO453
00662527
7. O-ring cl992 models>
8. Clamp
positionsensor removal steps
11 - Timing Belt)
9. Camshaft position sensor
10. Crankshaft position sensor
TSB Revision
Page 498 of 738
Downloaded from www.Manualslib.com manuals search engine 54-2
IGNITION SWITCH*..................................6
IGNITION SWITCH.................................
SPECIAL TOOL...................................6
LIGHTING SYSTEM................................35
FOG LIGHT....................................105
FRONT COMBINATION LIGHT AND
OPTICAL HORN LENS.........................106
HAZARD SWITCH..............................
110
HEADLIGHT...................................103
HIGH MOUNTED STOP LIGHT..................107
ON-VEHICLE SERVICE.........................100
POP-UP SWITCH AND FOG LIGHT SWITCH....109
REAR COMBINATION LIGHT AND
LICENSE PLATE LIGHT........................106
RELAY........................................108
RHEOSTAT....................................
110
SPECIAL TOOLS................................36
SPECIFICATIONS...............................
35
General Specifications..........................35Service Specifications..........................35
TROUBLESHOOTING............................37
METERS AND GAUGES..............................9
COMBINATION GAUGES........................33
COMBINATION METERS.........................31
ON-VEHICLE SERVICE...........................26
SPECIFICATIONS.................................
9
General Specifications............................9Sealant........................................ll
Service Specifications...........................11
TROUBLESHOOTING............................12
RADIO AND TAPE PLAYER.......................124
CD AUTO CHANGER..........................191
RADIO AND TAPE PLAYER WITH ANTI-THEFTSYSTEM.......................................156
MOTOR ANTENNA/ANTENNA FEEDERCABLE/AMPLIFIER.............................188
RADIO AND TAPE PLAYER....................186
RADIO REMOTE-CONTROL*...................186
SPEAKER.....................................
187
TROUBLESHOOTING...........................
124
REAR WINDOW DEFOGGER. . . . . . . . . . . . . . . . . . . . . .192
DEFOGGER RELAY. . . . . . . . . . . . . . . . . . . . . . . . . . . .204
ON-VEHICLE SERVICE. . . . . . . . . . . . . . . . . ~ ~. . . . . .203
REAR WINDOW DEFOGGER SWITCH . . . . . . -. . . 203
SPECIAL TOOLS.. . . s.. . . . . . . . . . . . . . . . . . . . . . . . .192
TROUBLESHOOTING
. . . . . . . . . . . . . . . . . . . . . . . . . . .193
REAR WIPER AND WASHER . . ~ *. . Refer to GROUP 51
SEAT BELT (BUZZER). . . . . . . . . . . . Refer to GROUP 52A
SEAT BELT (TENSION-REDUCERTYPE SEAT BELT) . . . . . . . . . . . . . . . Refer to GROUP 52A
SUPPLEMENTAL RESTRAINTSYSTEM (SRS)..-...............Refer to GROUP 52B
THEFT-ALARM SYSTEM . . . . . . . . . . . . . . . . . e . . . . . m.. s205
SPECIAL TOOLS.. . . . . . . . . . . . . . . . . . . .
m . . . . . . . .e205
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . .206
WINDSHIELD WIPER ANDWASHER. . . . . . . . . . . . . . . . . . . . . ~. . .Refer to GROUP 51
Page 612 of 738
Downloaded from www.Manualslib.com manuals search engine 54-116CHASSIS ELECTRICAL - Horn
CIRCUIT DIAGRAM
c
5W-B;;-j
. ANTI-LOCKBRAKING SYSTEM*&$@lJUISE
.BUZZER*E;~CT~R~ DOOR
.DOME LIGHTsFOOT LIGHTAND IGNITION KEY
CYLINDER ILLUMINATION
LIGHT
.DOOR LIGHT AND LUGGAGECOMPARTMENT LIGHT.ELC 4A/T'ELECTRONIC CONTROL
SUSPENSION:
FOG LIGHT
FULL AUTO A/C
'HEADLIGHT
.HEATER
'MANUAL A/C
. MFI SYSTEM.POWER WINDOW.RADIO ANDTAPE PLAYER. REAR WINDOW DEFOGGER. STARTING.STOP LIGHT.SUPPLEMENTAL
RESTRAINT SYSTEM
.TAILLIGHT PARKING/SIDE MARKER LIGHTfJy;H;ICENSE PLATE
.TENSION-REDUCER
TYPE SEAT BELT
.THEFT-ALARM SYSTEM*WINDSHIELD
WIPER AND WASHER
NOTE::UP TO 1995 MODELS
R-B
(A-06X)
I
G-B
(c-02)
G-B
(c-57)
GF
CLOCK
SPRING
[
GE
;;&CATED
G-R
!(
2E=
HORNG-R
(LH)c
E
=
'TCH
G-R
l(A-47),l (A-49)
>HORN
l(A-48)"1 (A-50)
B
0 (A-47) oFa (A-49) ofiml (c-02)(c-57)=
1993 MODELS) (FROM 1994 MODELS)
El
‘J ’
HROSMOSAA
1 TSB RevisionI
Page 684 of 738
Downloaded from www.Manualslib.com manuals search engine 54-188CHASSIS ELECTRICAL - Radio and Tape Player
MOTOR ANTENNA
/ ANTENNA FEEDER CABLE / AMPLIFIER
REMOVAL AND INSTALLATION
Motor antenna removal stepsl Rear side trim (LH)
(Refer to GROUP 52A
- Trims.)
1. Ring nut
2. Base
3. Antenna pole
4. Antenna feeder cable and motor antenna
connection5. Motor antenna
Amplifier removal
il. Amplifier (under passenger’s seat)
NOTE
l ‘: Refer to GROUP 52A - Trims‘*: Vehicels with glass mounted antenna
\Z16FO4974
Antenna feeder cable removal stepsl Rear side trim
(LH)*ll Quarter trim (LH)”
l Rear side trim*‘, **l Quarter trim (LH)*t, **l Quarter upper trim”, l *0 Liftgate upper trim*‘, +*l Ligate side trim (RH)“, l *l Rear console assembly(Refer to GOUP 52A - Console Box.)l Radio and tape player(Refer to P54-176)4. Antenna feeder cable and motor antennaconnection6. Rear seat cushion7. Rear seatback8. Inner seat belt
9. Console side cover (LH)
10. Antenna fedder cable
1 TSB Revision
Page 685 of 738
Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Radio and Tape Player54-I 89
Antenna going downAntenna going up
16FO203
16F019800002406
REMOVAL SERVICE POINT
+A,REAR SEAT CUSHION REMOVAL
Raise and remove the seat cushion with the lever pulled.
INSTALLATION SERVICE POINT
.AqREAR SEAT CUSHION INSTALLATION
(1) Securely fit the attachment wire of the seat cushion
under the seatback.
(2) Pass the inner seat belt buckles through the cushion.
(3) Securely fit the lock plates of the seat cushion into
the holes in the floor.
INSPECTION
ANTENNA MOTOR INSPECTION
Disconnect the motor antenna control unit connector, connect
the positive terminal of the power supply to terminal (1) and
connect the negative terminal to terminal (4) to check that
the antenna goes up, and that when the connections are re-
versed, the antenna goes down.
MOTOR ANTENNA CONTROL UNIT INSPECTION
(1) Connect the harness connector to the motor antenna.
(Body harness)
(2) Disconnect the antenna motor connector.
(3) With the ignition switch in the ACC or ON position, operate
the radio switch and check the voltage between the termi-
nals during the period when the antenna is going up or
going down.
I
I
Antenna operating
directionTerminals to checkVoltage (V)
I
Down
UPl-310-13
3-410-13
TSB Revision
Page 731 of 738
Downloaded from www.Manualslib.com manuals search engine ALPHABETICAL INDEX1
A
iiABSPOWER RELAY, Check . . . . . . . . . . . . . . . . . . . . , . . .
35-82-lRELAY.............................................35-110-1SIGNAL, On-vehicle Inspection.................13A-176,277-iACCELERATOR
CABLE..............................................
17-4-l
SWITCH
ACTIVE AERO SYSTEM, Check.........................
51-7-l
ACTIVE EXHAUST
CONTROL UNIT, On-vehicle Inspection..........13A-173,274-lSYSTEM............................................15-40-l
AERO PARTS........................................51-19-lAIR BAG..........................................520-74-lMODULE......................................528-82, 87-lAIR CLEANER.........................................15-9-l
ELEMENT, Maintenance..............................00-45-lAIR CONDITIONING...................................55-3-l
55-18-lCONTROL PANEL...................................55-73-lCONTROL UNIT.....................................55-73-lENGINE COOLANT TEMPERATURE SWITCHEngine Cooling.....................................14-13-l
ASSIST LINK
Maintenance
.........................................00-49-IAXLE
Rear
HUB, Rear -&VD>
....................................
27-4-lSHAFT
B
BALL JOINT SEALS, Maintenance. . . .
BAROMETRIC PRESSURE SENSOR
On-vehicle Inspection . . . . . . . . . . . .BASIC IDLE SPEED, Adjustment . . . . . .
BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . .
Discharged, Remedy . . . . . . . . . . . .
BELT LOCK CONTROLLER . . . . . . . . .
BLOWER. . . . . . . . . . . . . . . . . .
BOOSTER, Clutch
Parking. . . . . . . . . . ..*.............
BOOSTER . . . . . . . . . . . . . . . .
Operating Check . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .00-52-l
..........13A-91,217-l..............
13A-55-l................64-3-11................35-82-l............55-32,74-t................
55-35-l.................21-6-l.........13A-171,273-l
.................36-8-l................35-87-l................35-64-l
DISC..........................................35-93,103-l
Front, Check.......................................35-70-IRear, Check........................................35-73-lFLUID LEVEL SENSOR, Check........................35-64-l
HOSES, Maintenance.................................00-52-I
LINE................................................35-91-lLINING.............................................35-74-lPAD
Disc, Front.........................................
35-66-l
Disc, Rear.............~..................>..........35-71-lPEDAL.............................................35-84-l
Check and Adjustment......................
:........35-63-lBUMPERFront...............................................51-8-lRear...............................................51-13-l
CAMSHAFT
OIL SEALS..........................................
11-21-lPOSITION SENSOR, On-vehicle Inspection......13A-103,225-lCATALYTIC CONVERTER..............................17-71-l
..........................................
15-33-lCD AUTO CHANGER................................54-191-11CENTER PILLAR GLASS..............................42-33-l
CENTRAL DOOR LOCKING SYSTEM...................42-49-lCHARGE AIR COOLER................................15-11-l
CHARGING SYSTEM..................................l.6-2-11CIGARETTE LIGHTER..............................54-123-k
CLOCK SPRING, SRS..............................528-74-I
CLOSED THROTTLE POSITION SWITCH
Adjustment.......................................
13A-57-lOn-vehicle Inspection.........................13A-101,223-lCLUTCH
BOOSTER OPERATING, Check
MASTER CYLINDER.................................21-14-lPEDAL..............................................21-8-lCheck and Adjustment................................21-5-l
RELEASE CYLINDER................................21-16-IVACUUM LINE cAWD>...............................21-18-I
COLUMN SWITCH..................................54-112-11COMBINATION GAUGES.............................54-33-kCOMBINATION LIGHT...............................54-106-11COMBINATION METERS.............................54-31-11COMPRESSOR CLUTCH RELAY,On-vehicle Inspection...........................13A-123,236-lCONDENSER
Active Exhaust, On-vehicle Inspection...........13A-173,274-lECS.............................................338-20-I
Electronic CABS>..................................35-119-l
CONTROL VALVE.....................................37B-9-l
Fuel Tank Pressure..................................13F-6-IInspection..
........................................17-65-l
CRANKSHAFT
FRONT OIL SEAL....................................
11-25-lPOSITION SENSOR, On-vehicle Inspection......13A-107,227-l
REAR QIL SEAL.....................................11-26-l
Page 732 of 738
Downloaded from www.Manualslib.com manuals search engine ALPHABETICAL INDEX
CROSSMEMBER......................................32-8-lCRUISE CONTROL......................................17-t
CABLE, Check and Adjustment........................17-31-l
SYSTEM............................................17-38-i
Check.............................................
17-32-l
CURB IDLE SPEED, Check............................11-11-l
CYLINDER HEAD GASKET............................11-28-l
D
DAMPER CONTROL MOTOR..........................55-75-lDAMPING FORCE CHANGEOVER ACTUATOR........338-19-I
DASHPOT, Check And Adjustment......................11-l 3-lDEFOGGER
Rear Window.....................................54-192-11
RELAY............................................54-204-11
SWITCH, Rear Window.............................54-203-11
DIFFERENTIALCase, Limited Slip cAWD>...........................27-40-ILimited Slip, Check cAWD>..........................27-15-tCARRIER
DISC BRAKEFront..............................................35-93-lRear..............................................35-103-I
PADS, Maintenance..................................00-52-I
DOOR...............................................42-41-l
Adjustment.........................................42-12-lGLASS.............................................42-43-l
HANDLE............................................42-47-l
INSIDE HANDLE, Play Check..........................42-16-l
LATCH..............................................42-47-lMIRROR............................................51-31-l
REGULATOR........................................42-43-l
TRIM...............................................42-42- 1WATERPROOF FILM.................................42-42-lWINDOW GLASS, Adjustment.........................42-12-l
DRIP LINE WEATHERSTRIP...........................42-63-lDRIVE BELTCompressor, Adjustment.............................55-18-l
Maintenance.......................................00-47-I
Tension, Adjustment..................................11-7-l
Tension, Check.....................................37A-9-l
DRIVE SHAFTFront..............................................26-12-lRear...............................................27-19- I
BOOTS, Maintenance.................................00-52-l
OIL SEALS, Replacement
.......................23-53-l
E
ECSOn-vehicle Inspection..............................,338-l 1 -I
CONTROL UNIT...................................338-20-IINDICATOR LIGHT.................................338-19-ISWITCH..........................................338-18-I
EGR
SOLENOID..........................................17-70-l
On-vehicle Inspection.........................13A-164,269-l
SYSTEM, Inspection..................................17-67-l
TEMPERATURE SENSOR............................17-68-l
On-vehicle Inspection.........................13A-i35,246-I
VALVE..............................................17-68-l
VALVE CONTROL VACUUM, Check....................17-67-l
ELECTRICAL LOAD SWITCH, On-vehicle Inspection 13A-127,238-l
ELECTRONIC CONTROL UNIT
CABS>.................35-119-l
ENGINE.............................................11-18-l
CONTROL...........................................17-5-lCOOLANT
Maintenance.......................................00-51 -IReplacement........................................14-4-l
COOLANT TEMPERATURE GAUGE UNIT..............14-13-l
COOLANT TEMPERATURE SENSOR
Engine and Emission Control.........................17-65-l
Engine Cooling.....................................14-13-IOn-vehicle Inspection..........................13A-93,219-lHOOD..............................................42-18-l
MOUNTING..........................................32-3-lOIL, Maintenance....................................00-47-l
OIL COOLER........................................11-36-lOIL FILTER, Maintenance.............................00-48-l
ROLL STOPPER......................................32-6-l
SPEED ADJUSTING SCREW, Adjustment.............
13A-59-l
EVAPORATIVE EMISSION
CANISTER..........................................
17-65-l
CONTROL SYSTEM.................................17-57-l
Check for Leaks and Clogging........................00-46-l
PURGE SOLENOID..................................17-64-lOn-vehicle Inspection.........................13A-162,268-lEVAPORATOR........................................55-37-lEXHAUSTGAS RECIRCULATION (EGR) SYSTEM................17-66-l
MANIFOLD
PIPE
SYSTEM
Active.............................................15-40-l
Maintenance.......................................00-60-l
F
FAN MOTORCondenser
RELAY, On-vehicle Inspection...................13A-129.240-t
FEEDER CABLE, Antenna...........................54-188-11FENDER.............................................42-24-l
FILLER TUBE CAP, Fuel Tank, Check....................17-65-lFLOOR CONSOLE..................................52A-1 O-I
FLOOR PAN, Check...................................42-16-l
FOG LIGHT........................................54-105-11
SWITCH..........................................54-109-11FRONT IMPACT SENSORS..........................526-68-l
FUELFILLER DOOR, Adjustment............................42-12-l
FILTER............................................13F-10-I
GAUGE UNIT........................................13F-6-IHOSES, Maintenance.................................00-45-l
LINE................................................13F-8-I
PRESSURE SOLENOID, On-vehicle Inspection...13A-166,270-l
PRESSURE TEST, On-vehicle Inspection........13A-180,279-lPUMP..............................................13F-6-I
On-vehicle Inspection..........................13A-72,200-l
PUMP CIRCUIT RESISTOR, On-vehicle Inspection .
13A-84,211-lPUMP OPERATION CHECK, On-vehicle Inspection 13A-179,279-lPUMP RELAY N0.2, On-vehicle Inspection........13A-84,211-l
SYSTEM, Maintenance...............................00-45-I
FUEL TANK..........................................13F-3-IFILLER DOOR.......................................42-23-lFILLER TUBE CAP, Check............................17-65-l
PRESSURE CONTROL VALVE........................
13F-6-IInspection..........................................17-65-l
FULL AUTO AIR CONDITIONING.......................55-54-l