ENGINE MOUNT MITSUBISHI 3000GT 1995 2.G User Guide

Downloaded from www.Manualslib.com manuals search engine HEADLIGHT
CHASSIS ELECTRICAL - Lighting System54-103
REMOVAL AND INSTALLATION
(From 1994 models)
(Up to 1993 models)
Removal steps (From 1994 models)
1. Front combination light
2. Headlight
4Bb
4WFOOB100002389
Removal steps (Up to 1993 models)
1. Headlight bezel, upper
2. Headlight bezel, lower
3.Retaining ring4.Headlight5.Spring6.Mounting ring7.Housing8.Rod assembly9.Headlight hood
10.Link assembly11. Boot12. Pop-up motor
REMOVAL SERVICE POINTS
+A, HEADLIGHT BEZEL, UPPER REMOVAL(1) Raise the headlights by using the pop-up switch.
Disconnect the negative (-) battery terminal.(2) Remove the headlight bezel, upper.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Lighting System54-105FOG LIGHT
REMOVAL AND INSTALLATION
(Up to 1993 models)
,’
..-.-f .- . . .._ 1’yI’-’--.._ . . . ./’‘._,/‘.:‘. . . . . .--ye=.,/‘c’ !:I’:.;; ____-... _.__-.-__~___. . . . . ._./i L.- -3...-.._:.y- .‘...-____ y--. . . . . --‘-T---..-_ -_--._ _ __.-.-.;.? ::.._/ ; .--_.‘7 ,,-y-? ..-,r-; ‘;
‘....lr/I..j ,/L7 rl,-’/I” . . . ..-. ~ -,-.-A:..____ p
A’7----p--*@
,,A..
*~~~~1;’ -“‘.,.
, ‘!U ,.I,/ Ii
8, $&$Jqk2&
4&;. +I+ ’
,,, ’ .’- ‘-I,i
4!a
Removal steps(Up to 1993 models)
1. Front air side spoiler2. Fog light assembly -3. Socket cover4. Bulb
Up to 1993 models
Z16FO268
From1994 models
wZl6FO465
(From 1994 models)
(From 1994 models)
1. Front air side spoiler2. Fog light assembly
Bulb replacement removal steps4.
Lens5. Projector unit6. Bulb7. Bracket
REMOVAL SERVICE POINT
+A, BULB REMOVAL(1) Remove the socket cover (Up to 1993 models).
(2) Remove the bulb mounting spring and remove the
bulb.
CautionDo not touch the surface of the headlight bulb
with bare hands or dirty gloves.
If there are deposits on the surface, loosen and
remove the deposits with a cloth dipped in alcohol
or thinner, and let the surface dry before mounting
the bulb.
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Lighting SystemHIGH MOUNTED STOP LIGHT
REMOVAL AND INSTALLATION

Z 16FO229Z 16FO229
‘\ \/4
116FcJ23100002393 00002393
Removal steps
1. Liftgate lower trim(Refer to GROUP 52A - Trims.)2. Rear spoiler(Refer to GROUP 51 - Aero Parts.)3. High mounted stop light
1. Light unitg. ;S;ke’ assembly
Removal steps
1. Liftgate lower trim(Refer to GROUP 52A - Trims.)2. High mounted stop light cover3. ;;z;keyounted stop light lens and
4. Gasket
&I REMOVAL SERVICE POINT
4A, HIGH-MOUNTED STOP LIGHT REMOVAL
(Vehicles with fixed rear spoiler)
Remove the air spoiler center stay mounting screws beforeremoving the high-mounted stop
light.

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Radio and Tape Player54-159
CHARTA. NOISE
A-l
Noise appears at certain places when traveling (AM).Is there a particular
stFind out the following information from the user:
1. Place
h YesDo the following measures eliminate the noise?
1. Change to a different station with a strong signalto boost resistance to interference.
2. Suppress high tones to reduce noise.
No
2. Locality conditions (valley, mountain, etc.)3. Name and frequency of stations affected by noise
tIf due to vehicle noise:
It may not be possible to prevent noise if the
signal is weak.
-I
t1 If due to external noise:
In almost all cases, prevention on the receiver
Weak signals especially are susceptible to inter-
i
tIf there is more noise than other radios, find out the noise conditions
and the name and frequency of the receiving stations from the user,and consult with the service center.
iTSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-160CHASSIS ELECTRICAL - Radio and Tape Player
A-2Noise appears at certain places when traveling (FM).Do the following measures eliminate the noise?
YeslChange to a different station with a strong signal to boost resistance to interference.l Suppress high tones to reduce noise.+3cll Extend antenna completely. (Whip antenna)
No
tIf there is more noise than other radios, find out the noise conditions and the name and frequency
of the receiving stations from the user, and consult with the service center.
NOTE
About FM waves:
FM waves have the same properties as light, and
can be deflected and blocked. Wave reception isnot possible in the shadow of obstructions such
as buildings or mountains.
1.The signal becomes weak as the distance from
the station’s transmission antenna increases.
Although this may vary according to the signal
strength of the transmitting station and interven-ing geographical formations or buildings, the
area of good reception is approx.
20-25 km
(12-l 6 miles) for stereo reception, and 30-40km (19-25 miles) for monaural reception.
2. The signal becomes weak. when an area of
shadow from the transmitting antenna (places
where there are obstructions such as mountains
3.
4.
or buildings between the antenna and.the car),
and noise will appear. and gives a steady buzzing noise.>
If a direct signal hits the antenna at the same
time as a signal reflected by obstructions such
as mountains or buildings, interference of the
two signals will generate noise. During traveling,
noise will appear each time the vehicle’s anten-
na passes through this kind of obstructed area.The strength and interval of the noise varies
according to the signal strength and the condi-tions of deflection.
noise, and is a repetitious buzzing.>Since FM stereo transmission and reception
has a weaker field than monaural, it is often
accompanied by a hissing noise.FM Broadcast Good Reception Areas
FM Signal Characteristics and Signal Interference
For home stereos:80-90 km (SO-56 miles):.:,.::..:,.::.‘; .: ‘, “.‘l’.. ”216AO664Z16A066300002401
Iji
I
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-I 62CHASSIS ELECTRICAL - Radio and Tape Player
A-4
Broadcasts can be heard but both AM and FM have a lot of noise.
(1)Noise occurs when the engine is stopped.
YesJ
(2)Noise occurs when the engine in running.
Do the following measures eliminate the noise?
@ Tune to a station with a strong signal.
l Extend the antenna completely. (Whip antenna)
l Adjust the sound quality to suppress high tones.
NoIs the radio body ground mounted securely?
Yes
Securely tighten the nuts for the bodyground.
Yes
YesClean the antenna plug and ground
wire mounting area. Mount the anten-
na securely. On a vehicle with a motor
antenna, check the antenna itself. (Re-fer to E-1, 2.)
If there is more noise than other radios, consult a servicecenter
NOTE
About noise encountered during FM reception only.
Due to differences in FM and AM systems, FM is
noise interference (first fading and multipath). (Refer
to A-2.)
not as susceptible as AM to interference from en-
gines, power lines, lightning, etc. On the other hand,
problem with the radio.>waves of noise or distortion generated by typical
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Radio and Tape Plavers54-163 ~
A-5There is more noise either on AM or on FM.1. There is much noise
onlv on AM
Due to differences in AM and FM systems, AM
is more susceptible to noise interference.Were conditions such as the following present when noise was received?
l Lightning was flashing. A motorcycle was passing.
l
Avehicle passed close by, but it appeared to be avehicle generating a particularlylarge amount of noise radiation.
l Passed beneath a power line. Passed under a bridge.
l Passed beneath a telephone line.
l Passed close by a signal generator.
l Passed close by some other source of electrical noise.
.I-!
I
NO
Yes
. .F- Norse prevenoon on Me radro srde IS difficult. If theproblem is particularly worse than other radios, consulta service center.Continue to check for static; whe
the conditions listed aboveNoYest
If the problem is particularly worse than
other radios, consult a service center.
2. There is much noise only on FM
Due to differences in FM and AM systems, FM
is not as susceptible as AM to interference from
engines, power lines, lightning, etc. On the other
hand, there are cases due to the characteristicsof FM waves of noise or distortion generated
by typical noise interference (first fading and
multipath). (Refer to A-2)
curs in weak signal areas such as mountainous
regions, but this is not due to a problem with
the radio.>
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Radio and Tape Player54-165
NOISE SUPPRESSION PARTS MOUNTING POSITIONS
1/ Noise con::;;, 1
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-166CHASSlS ELECTRICAL - Radio and Tape Player
IA-7Some noise appears when there is vibration or shocks during traveling.
‘d ~
Are connectors properly connected?
YesNo
---+ Ensure proper connection
t
Does noise appear when the radio switch is turned on while theNovehicle is stopped and the radio is struck while tuned away fromLa station?
YesStatic electricity noise:
Body static electric from the shock absorber rubber bushings used
to prevent vibration, tires, etc. occurs because of separation fromthe ground, causing a buzzing noise.
Since no measures can be taken on the radio side, steps shouldbe taken to discharge the static electricitv of the vehicle bodv.
tIs the radio correctly grounded?
(Is the mounting screw tightened securely?)
1 Yes
tIs the antenna correctly grounded? (If noise appears when the Nocantenna is moved, this means the ground is not securely con-
nected.)
If rust is present on the antenna ground screw, clean and tightenthe ground securely.
Yes
1 Reoair or reolace radio.1
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Radio and Tape Player54-167
A-8Noise sometimes appears on FM during traveling.
NoIs the antenna completely extended?
Yes
t Check the antenna itself.
(Refer to E-l, 2.)
+Does the problem clear up whenre
1 No
Yes
iDoes the problem appear only in certain locations and only with yes
certain stations?
No
~ Due to electrical field conditions. (Multipath
noise*, fading noise*).
Are connectors property connected?
Yes
Check connector connections.1
tDoes noise appear when the radio switch is turned on while the
vehicle is stopped
and the radio is struck while tuned away froma station?
Yes
No*Static electricity noise:Sody static electric from the shock absorberrubber bushings used to prevent vibration, tires,etc. occurs because of separation from the
ground, causing a buzzing noise.
Since no measures can be taken on the radioside, steps should be taken to discharge the
static
electricitv of the vehicle bodv.
Is the radio body correctly grounded?
No(Is the mounting screw tightened securely?
)
Yes
-) Tighten the screw securely.I
Is the antenna correctly grounded? (If noise appears when the antennais moved, this means the ground is not securely connected.)
Yes
If rust is present on the antenna ground screw,clean and tighten the ground securely.
*
1 Repair or replace radio.1
About multipath noise and fading noise
Because the frequency of FM waves is extreme-
ly high, it is highly susceptible to effects from
geological formations and buildings. These ef-
fects disrupt the broadcast signal and obstruct
‘reception in several ways.l Multipath noise
This describes the echo that occurs when the
broadcast signal is reflected by a large obstruc-
tion and enters the receiver with a slight time
delay relative to the direct signal (repetitious
buzzing).l Fading noise
This is a buzzing noise that occurs when the
broadcast beam is disrupted by obstructing ob-
jects and the signal strength fluctuates intricately
within a narrow range.
1 TSB Revision