Wiper MITSUBISHI 3000GT 1995 2.G User Guide

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Power Distribution Circuit
L,
FUSIB ELINK 4bB
P3w P
$$d! CONTROL
jj!JyTDIAGNOSIS
.STARTER MOTOR$$eEl?ER
2L-w
:
J
I
2B-b
7@#"TO"
2__-__--__-__-_--_--_--~~-~~-~-- -_-----__-_--_C\
1I/4,/---t-_
/
i/.ENGINECONTROL MODULE.IGNITION COIL.IGNITION POWERTRANSISTOR.MFI RELAY
.REMOTECONTROLLED
MIRROR
.AUTO-CRUISECONTROL UNIT.ETACS UNIT.MOTOR ANTENNACONTROL UNIT.RADIO ANDTAPE PLAYER
.BACK UP LIGHT.LIGHT AUTOMATICSHUT-OFF UNIT.;;~TDIAGNOSIS
i
.REARINTERMITTENT
WIPER RELAY
.WASHER MOTOR.WIPER MOTOR.WIPER RELAY@L"'$jGER
:ACTIVE AEROCONTROL UNIT~~~&~~U'SE
MAIN SWITCH$&CRUISE
.@j&NATION
$'~$!$NATION
:.ETACS UNIT '.MOTOR ANTENNACONTROL UNIT.SPEED SENSORjiyTDIAGNOSIS
*TURN SIGNALAND HAZARD
FLASHER UNITr
*
.AIR CONDITIONING\
COMPRESSOR LOCK.CONDENSOR
CONTROLLER;@AiOTOR
.AIR CONDITIONINGCONTROL UNIT.~@;~~NIC
.&A";R MOTORSUSPENSIONCONTROL UNIT
.BLOWER MOTOR.RADIATORRELAY(HI)&JAFOTOR
THE ABOVE CIRCUIT DIAGRAM SHOWS THE CURRENT FLOW AT THE
IGNITION KEY POSITION "ACC", "ON" AND "ST" COMBINED
BE SURE TRACE THE APPROPRIATE CIRCUIT DEPENDING ON THEIGNITION KEY POSITION.
X:HATCHBACK
HROlM03BB
TSB Revision

Downloaded from www.Manualslib.com manuals search engine Full Auto Air Conditioning Circuit /CIRCUIT DIAGRAMS
- Windshield Wiper and Washer Circuit
Interior temperaturesensorI
WINDSHIELD WIPER AND WASHER
COMPONENT LOCATION
Data link connectoru------J\ .r7===-lc7c7%
tI-L \X16Fo?m I
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Windshield Wiper and Washer Circuit315
OPERATION/
LlWhen the wipe: switch is placed in the OFF
l When the wiper switch is placed in the LO
position, the cam contacts of wiper motor causesposition with the ignition switch in the ACC orcurrent to flow through the auto wiper stop
ON position, wipers operate continuously at lowcircuit, allowing the wiper blades to cycle before
speed.they reach to the stop position.
l Placing the wiper switch in the HI position
causes the wipers to operate at high speed.


lIf the washer switch is on for 0.6 second or
less when the ignition switch is at ON or ACC
lIf the wiper switch is turned to the INT positionwith the wiper switch turned off, the washer
when the ignition switch is in the ON or ACCliquid will not be poured but transistor will be
position, the voltage value from the intermittentturned on to operate the wipers one time.
variable volume switch is input to intermittent

’time detection circuit.
l The intermittent time detection circuit outputs
an H signal at the intermittent time according
to the set value of the intermittent variable
volume switch and, via OR, turns the Tr on
and off to operate the wiper.lIf the washer switch is on for 0.6 second or
more when the ignition switch is at ON or ACC
with the wiper switch turned off, the washer
liquid will be poured and the transistor will be
turned on 0.6 second later to operate the wipers
two or three times.
TROUBLESHOOTING HINTS
L
PhenomenonWipers do not operate Washer does not operate.
continuously
Washer operates.Inspecting method
lCheck the multi-purpose fuse No. 9l Check the wiper motor. (Refer to GROUPS-Windshield
Wiper and Washer.)l Check the column switch. (Refer to GROUPS-Windshield
Wiper and Washer.)Low-speed (or high-speed) wiper operation only is l
inoperative.Check the column switch. (Refer to GROUP51-Windshield Wiper and Washer.)
Wipers do not operate intermittently.
(They operate continuously.)lCheck the wiper switch “INT” input signal. (Refer
to GROUP
51-Troubleshooting.)l Check the column switch. (Refer to GROUPS-Windshield
Wiper and Washer.)
Wipers do not stop.lCheck the wiper switch “INT” input signal. (Refer
to GROUP
51-Troubleshooting.)l Check the column switch. (Refer to GROUP
51-Windshield Wiper and Washer.)
o Check the wiper motor. (Refer to GROUP
51-Windshield Wiper and Washer.)The intermittent time will not vary even if the variable l
intermittent wiper control switch is operated.
Check the variable intermittent wiper control switch
input signal. (Refer to GROUP S-Troubleshooting.)l Check the column switch. (Refer to GROUP
51-Windshield Wiper and Washer.)
Even if the washer switchThe wipers linked with the lCheck the washer motor. (Refer to GROUP
is on for 0.6 second or
washer operate.51-Windshield Wiper and Washer.)
more,. the washer will notlCheck the washer nozzle and washer tube.
operate.The wipers linked with the lCheck the washer switch input signal.
washer do not operate.l Check the washer switch. (Refer to GROUP51-Windshield Wiper and Washer.)
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Windshield Wiper and Washer CircuitWINDSHIELD WIPER
AND WASHER CIRCUIT
\ie/~
FUSIBLE LINKaIIGNITION SWITCH(ACC)I
2W-B
HORN5w-B,,1 (c-68)&, 4
JIBiI2-pI
13Ab15Ab15Ab ;\IV\,\,
O"11=---y(c-701::-J
2w i 'pun, 1T8&.;~~~~ORY
\(F)R-BI "'1; "I, , @@"R'!I
0.85L
NOTE:l:VEHICLES WITHOUT THEFT-ALARM SYSTEMx2:VEHICLES WITH THEFT-ALATM SYSTEM
"GARETTF
I- . -. . . .- . _ -LIGHTER\
LG
_I53 (c-66)---------_____,.I\
IA 7h6I
WIPER RELAYIWASHER SWITCH 1WIPER SWITCHI
-10w9‘8
(c-83) ',,4 LG
J/B A
0.85L-WV
(C-82) *B“50
nLG
B0c
HR13MOGAATSB Revision
d

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAlViS - Windshield Wiper and Washer Circuit
IGNITION SWITCH(IG1)WIPERIGNITION
J/BRELAYSK?"
+CHARGING
J/B
(F>R-B
I
(F)R-B
DOOR LIGHT
AND LUGGAGE0.858-WS(c-71)LGE~$;;RTMENT
0.858-WFs(D-44)
0.85B-W
0.85L-(0.85L-0.85L-A0. 85
TURN-SIGNAL LIGHT
AND HAZARD LIGHT
NOTEtl:VEHICLES WITHOUTTHEFT-ALARM SYSTEM g
:2:VEHICLES WITHTHEFT-ALARM SYSTEM 2
x3:UP TO 1995 MODELS%4:FROM 1996 MODELS5--
ETACS UNITYmG"106 (D-05)LG
--------
18 (c-29)
--------6
_--_----.5_----___1617
R-B
/!i,
M
2
:c-ss)54
B
0.85L-(0.85L-0.85L-h0.85
43
%3
2B-$
B-L
B B
16945I
A
i%RMOTOR
(A-15)
LDATA LINKCONNECTOR
(c-79)
2B1.25B
NOTEDATE LINK POWER SOURCE CIRCUIT
AND GROUND CIRCUIT
ARE APPLICABLE FROM 1994 MODELS
tzB
(c-79) gygTE%Eo(D-04)(D-05)(D-44)
(UP TO 1993 MODELS))
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine 318CIRCUIT DIAGRAMS - Rear Wiper and Washer Circuit
REAR WIPER AND WASHER CIRCUIT
IGNITION SWITCH(ACC)TAILLIGHT RELAY
I
REAR(c-82)INTERMITTENTWIPER RELAYDEDICATEDFUSE
I.Ji--mm I -1*..I
1 viI1 \/ 1, V0.85Li"4" 1"2"5
L
T
OL3$ OBJ$B-L
----------J,14--------------____,,17 ,,16------,0. 85 B-Lc-w
0.85
0.85
(F>0. a:
0.85L1
,\ 647GLOVE BOX LIGHTI\
REARWIPERSWITCH
REAR WIPER&;PT;/SHER
(D-37)ILLd3
-----57m
1
(F)
"if;
2
2
I
REARWASHERI MOTOR
(F-15)
E1
0
RHEOSTAT
2EI
z(D-41)
28
n6
0.85~~0.85L-b
----,
(F)
"ifi
0.85~~
2B
HR13M04AA
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Rear Wiper and Washer Circuit
COMPONENT LOCATION
OPERATION

0 When the rear wiper switch is placed in the
ON position with the ignition switch in the ACC
or ON position, wipers operate continuously at
low speed.
l
When the rear wiper switch is placed in the
OFF position, the cam contains of wiper motor
causes current to flow through the auto wiper
stop circuit, allowing the wiper blades to cycle
before they reach to the stop positions.
i
l
When the rear wiper switch is placed in the
INT position with the ignition switch in ACC
or ON position, the rear intermittent wiper relay
is energized causing the rear intermittent wiper
relay contacts to close and open repeatedly.l
When the contacts are closed, the wiper motor
is energized.l
When the rear wiper motor is energized, the
rear intermittent wiper relay contacts open;
however, the cam contacts keep the rear wiper
motor energized until the wiper blades return
to their stop position.
TROUBLESHOOTING HINTS
1. Wipers do not operate.
(1) Washer is not operative, either.l
Check multi-purpose fuse No. 9.l
Check ground.
2.Low-speed wiper operation only is inoperative.l
Check wiper switch.
3. Wipers do not stop.l
Check wiper motor.l
Check rear intermittent wiper relay.l
Check rear wiper switch.
4. Intermittent wiper operation is inoperative.l
Check terminal voltage of the rear
intermittent wiper relay energized.
(Refer to GROUP 51-Windshield Wiper and
Washer for information concerning the
installation position of the intermittent wiper
relay.)
Terrr$al 1 Voltage
I
12v
0 3-b 12v
1 (alternating)
5. Washer is inoperative.l
Check washer motor.l
Check washer switch.
Check
Rear intermittent
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-2
IGNITION SWITCH*..................................6
IGNITION SWITCH.................................
SPECIAL TOOL...................................6
LIGHTING SYSTEM................................35
FOG LIGHT....................................105
FRONT COMBINATION LIGHT AND
OPTICAL HORN LENS.........................106
HAZARD SWITCH..............................
110
HEADLIGHT...................................103
HIGH MOUNTED STOP LIGHT..................107
ON-VEHICLE SERVICE.........................100
POP-UP SWITCH AND FOG LIGHT SWITCH....109
REAR COMBINATION LIGHT AND
LICENSE PLATE LIGHT........................106
RELAY........................................108
RHEOSTAT....................................
110
SPECIAL TOOLS................................36
SPECIFICATIONS...............................
35
General Specifications..........................35Service Specifications..........................35
TROUBLESHOOTING............................37
METERS AND GAUGES..............................9
COMBINATION GAUGES........................33
COMBINATION METERS.........................31
ON-VEHICLE SERVICE...........................26
SPECIFICATIONS.................................
9
General Specifications............................9Sealant........................................ll
Service Specifications...........................11
TROUBLESHOOTING............................12
RADIO AND TAPE PLAYER.......................124
CD AUTO CHANGER..........................191
RADIO AND TAPE PLAYER WITH ANTI-THEFTSYSTEM.......................................156
MOTOR ANTENNA/ANTENNA FEEDERCABLE/AMPLIFIER.............................188
RADIO AND TAPE PLAYER....................186
RADIO REMOTE-CONTROL*...................186
SPEAKER.....................................
187
TROUBLESHOOTING...........................
124
REAR WINDOW DEFOGGER. . . . . . . . . . . . . . . . . . . . . .192
DEFOGGER RELAY. . . . . . . . . . . . . . . . . . . . . . . . . . . .204
ON-VEHICLE SERVICE. . . . . . . . . . . . . . . . . ~ ~. . . . . .203
REAR WINDOW DEFOGGER SWITCH . . . . . . -. . . 203
SPECIAL TOOLS.. . . s.. . . . . . . . . . . . . . . . . . . . . . . . .192
TROUBLESHOOTING
. . . . . . . . . . . . . . . . . . . . . . . . . . .193
REAR WIPER AND WASHER . . ~ *. . Refer to GROUP 51
SEAT BELT (BUZZER). . . . . . . . . . . . Refer to GROUP 52A
SEAT BELT (TENSION-REDUCERTYPE SEAT BELT) . . . . . . . . . . . . . . . Refer to GROUP 52A
SUPPLEMENTAL RESTRAINTSYSTEM (SRS)..-...............Refer to GROUP 52B
THEFT-ALARM SYSTEM . . . . . . . . . . . . . . . . . e . . . . . m.. s205
SPECIAL TOOLS.. . . . . . . . . . . . . . . . . . . .
m . . . . . . . .e205
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . .206
WINDSHIELD WIPER ANDWASHER. . . . . . . . . . . . . . . . . . . . . ~. . .Refer to GROUP 51

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Meters and Gauges54-31
COMBINATION METERS
LREMOVAL AND INSTALLATION
76FO22200002364
NOTE
*: 1992 models
L/
:i:
- lnstiument PineI.)
2. Column cover, lower
3. Column cover, upper 1. Knee protector (Refer
G GROUP 52A4. Meter bezel
* ’5. Combination meter
Removal steps6. Adapter* (Mechanical speedometer
type) /Washer tank (Refer to GROUP
51 - Windshield Wiper and Washer.)7. Vehicles speed sensor (Electrical
Front of ve
219FOl;
speedometer type)REMOVAL SERVICE POINTS
dAbCOLUMN COVER LOWER / COLUMN COVER
UPPER REMOVAL
After the screws have been removed, remove the covers,while making sure not to break the grippers.
dB, ADAPTER REMOVAL TYP-
(1) Disconnect the speedometer cable at the transaxle
end of the cable.
(2) Pull the speedometer cable slightly toward the vehicleinterior, release the lock by turning the adaptor to
the left or right, and then remove the adapter.
Adapter-Y16FO129],
) TSB RevisionI

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Column Switch
COLUMN SWITCH
SPECIFICATIONS
GENERAL SPECIFICATIONS
54-111
ItemsSpecifications
1 Lighting switchRated load A1 0.22 f 0.05IIII
1 Voltage drop V0.2 or less
I Turn-signal switch) Rated load A1 6.6kO.5III/I
Dimmer/passing switch
Voltage drop V
Rated load A
0.2 or less
High beam : 10.7 + 0.8IIII
1 Low beam : 9.8 f 0.7IIII
j Passing : 20.5 + 1.5IIII
/ Voltage drop V0.2 or less
NOTE
For the wiper and washer switch, refer to GROUP 51 - Windshield Wiper and Washer.SPECIAL TOOL
Steering wheel puller
1 TSB Revision