4WD MITSUBISHI ASX 2017 (in English) User Guide

Drive modeDisplayType 1Type 22WD4WD AUTO4WD LOCKCAUTIONlDo not operate the drive mode-selector with
the front wheels spinning on a snowy road or
in similar conditions. The vehicle could
lunge in an unexpected direction.
l Driving on dry, paved roads in “4WD
LOCK” mode causes increased fuel con-
sumption and noise.
l Do not drive with the tyres spinning in
“2WD” mode.
Doing so could generate heat in the drive- system components.NOTEl The drive mode can be switched while driv-
ing or stopped.Drive mode indicatorType 1Type 2
Normally the indicator illuminates when the
ignition switch is turned to the “ON” position or the operation mode is put in ON, and then
the drive mode is displayed a few seconds af- ter the engine is started.
Drive mode
Drive mode indicator“4WD” indi-
cator“LOCK” in-dicator2WDOFFOFF4WD AUTOONOFF4WD LOCKONONCAUTIONlIf the selected drive mode indicator is blink-
ing, the vehicle switches automatically to front-wheel drive in order to protect thedrive-system components, and drive mode
selection is no longer possible with the drive mode-selector.
The warning display is also displayed in the
information screen in the multi-information display.
Reduce speed, and if the indicator goes out after driving a while, resume driving as be-fore.Type 1Type 2CAUTIONl If the warning display on the information
screen in the multi-information display, a problem has occurred with the electronically
controlled 4WD system and the safety de-
vice has activated. Have your vehicle in-
spected immediately by a MITSUBISHI
MOTORS Authorized Service Point.
Electronically controlled 4WD system*
6-40OGAE17E2Starting and driving6

Type 1Type 2CAUTIONlAlways use tyres of the same size, same
type, and same brand, and which have no wear differences. Using tyres that differ in
size, type, brand, or wear amount may acti- vate the protection of the drive-system com-
ponents, causing the drive mode in “4WD
AUTO” mode to lock or the “4WD” and “LOCK” indicators to blink alternately.4-wheel drive operation
E00606601116
Your vehicle has been designed primarily foruse on paved roads.
But its unique 4-wheel drive system allows
you to occasionally travel on unpaved roads, to campgrounds, picnic sites, and similar lo-
cations.
Not only does this ensure better handling on
dry, paved roads but also permits better trac-
tion when driving on slippery, wet or snow- covered roads and when moving out of mud.
But it is not suitable for heavy off road use or
towing in rough conditions.
It is particularly important to note that 4-
wheel drive may not give sufficient hill
climbing ability and engine braking on steep slopes. You should try to avoid driving on
steep slopes.
Also, you must exercise caution when driving on sand and mud and when driving through water because sufficient traction may not be
available in certain circumstances.
Please avoid driving the vehicle through
areas where the tyres may get stuck in deep
sand or mud.WARNINGl Do not over-rely on the 4-wheel drive ve-
hicles. Even 4-wheel drive vehicles have limits to the system and ability to main-tain control and traction. Reckless driving may lead to accidents. Always drive care-
fully, taking account of the road condi-
tions.
l Improperly operating this vehicle on or
off-paved roads can cause an accident or
rollover in which you and your passengers
could be seriously injured or killed.
• Follow all instructions and guidelines in
the owner’s manual.
• Keep your speed low and do not drive
faster than conditions allow you to.NOTEl Driving on rough roads can be hard on a ve-
hicle. Before you leave paved roads, be sure all scheduled maintenance and service has
been done, and that you have inspected your vehicle. Pay special attention to the condi- tion of the tyres, and check the tyre pres-
sures.
l MITSUBISHI
MOTORS is not responsible
to the operator for any damage or injury caused or liability incurred by improper and
negligent operation of a vehicle. All techni- ques of vehicle operation depend on the skill and experience of the operator and other par-
ticipating parties. Any deviation from the recommended operating instructions above
is at their own risk.
l Note that the stopping distance required of a
4-wheel drive vehicle differs very little from
that of a 2-wheel drive vehicle. When driv-
ing on a snow-covered road or a slippery, muddy surface, make sure that you keep a
sufficient distance between your vehicle and the one ahead of you.
l The driving posture should be more upright;
adjust the seat to a good position for easy
steering and pedal operation. Be sure to wear
the seat belt.
l After driving on rough roads, check each
part of the vehicle and wash it thoroughlywith water. Refer to the “Inspection andmaintenance following rough road opera-
tion” section and “Maintenance” section.
4-wheel drive operation
6-41OGAE17E2Starting and driving6

CAUTIONlSetting the drive mode-selector to “4WD
LOCK” to drive on dry paved road will in-
crease fuel consumption, with possible noise generation.
Turning sharp corners
When turning a sharp corner in “4WD
LOCK” position at low speed, a slight differ- ence in steering may be experienced similar
to as if the brakes were applied. This is called tight corner braking and results from each of
the 4 tyres being at a different distance from
the corner. The phenomenon is typical of 4- wheel drive vehicles. If this occurs, either
straighten out the steering wheel, or change to “2WD” or “4WD AUTO” mode.
On snowy or icy roads
Set the drive mode-selector to “4WD AUTO”
or “4WD LOCK” in accordance with the road conditions, and then gradually depress the accelerator pedal for a smooth start.
NOTEl The use of snow tyres is recommended.NOTElMaintain a safe distance between vehicles,
avoid sudden braking, and use engine brak-
ing (downshifting).CAUTIONl Avoid sudden braking, sudden acceleration
and sharp turning. Skidding occurs and con-
trol of the vehicle could be lost.
Driving on sandy or muddy
roads
Set the drive mode-selector to “4WD LOCK”
and then gradually depress the accelerator pedal for a smooth start. Keep the pressure on
the accelerator pedal as constant as possible,
and drive at low speed.
CAUTIONl Do not force the vehicle or drive recklessly
on sandy surfaces. In comparison with nor-
mal road surfaces, the engine and other
drive-system components are put under ex- cessive strain when driving on such a sur-
face. This could lead to accidents.CAUTIONl If the engine coolant temperature display flashes on the information screen in the mul-
ti-information display or the engine power
drops suddenly while the vehicle is being driven, park your vehicle immediately in asafe place.
Refer to “Engine overheating” on page
8-04 for details and take the required meas-
ures.WARNINGl When attempting to rock your vehicle out
of a stuck position, be sure that the area
around the vehicle is clear of people and physical objects. The rocking motion may
cause the vehicle to suddenly launch for- ward or backward, causing injury or damage to nearby people or objects.NOTEl Avoid sudden braking, sudden acceleration
and sharp turning; such operations could re-
sult in the vehicle becoming stuck.
l If the vehicle becomes stuck in sandy or
muddy roads, it can often be moved with a
rocking motion. Move the gearshift lever al-
ternately between the 1 st
and “R” (Reverse)
positions ( M/T), the “D” (DRIVE) and “R”
(REVERSE) positions ( A/T or CVT), while
pressing lightly on the accelerator pedal.
4-wheel drive operation
6-42OGAE17E2Starting and driving6

The regulations concerning towing may dif-
fer from country to country. It is recommen-
ded that you obey the regulations of the area where you are driving your vehicle.
Towing the vehicle by a tow
truckCAUTIONl This vehicle must not be towed by a tow
truck using sling lift type equipment (Type A) as illustrated. Using a sling lift will dam-age the bumper and front end.
l Do not tow 2WD vehicles with CVT with
the driving wheels on the ground (Type B) as illustrated.
This could result in the driving system dam- age.
l Do not tow 4WD vehicles with the front or
rear wheels on the ground (Type B or Type C) as illustrated. This could result in drivingsystem damage or the vehicle may jump at
the carriage.
If you tow 4WD vehicles, use Type D or E
equipment.
l On 2WD vehicles, if the transmission is mal-
functioning or damaged, transport the vehi- cle with the driving wheels on a carriage (Type C, D or E) as illustrated.
l The 4WD vehicles cannot be towed with on-
ly the front or rear tyres on the ground even
if they are in “2WD” drive mode.
Towing
8-21OGAE17E2For emergencies8Do not tow 4WD vehicles, or 2WD vehicles
with CVT, with this style.
Do not tow 4WD vehicles with this style.

CAUTIONlA temporary spare tyre can be fitted tempo-
rarily in place of a tyre that has been re-
moved during the tyre rotation. However, it must not be included in the regular tyre rota-
tion sequence.
l If the tyres have arrows (A) indicating the
correct direction of rotation, swap the front
and rear tyres on the left-hand side of the ve- hicle and the front and rear tyres on the right-hand side of the vehicle separately. Keep each tyre on its original side of the ve-
hicle. When fitting the tyres, make sure the
arrows point in the direction in which the wheels will turn when the vehicle moves forward. Any tyre whose arrow points in the
wrong direction will not perform to its full potential.Front
CAUTIONl Avoid the combined use of different types of
tyres.
Using different types of tyres can affect ve-
hicle performance and safety.Snow tyres
E01002001852
The use of snow tyres is recommended for
driving on snow and ice. To preserve driving stability, mount snow tyres of the same size and tread pattern on all 4 wheels.
A snow tyre that is worn down more than
50% is no longer appropriate to use.
Snow tyres which do not meet specifications must not be used.
CAUTIONl Observe permissible maximum speed for
your snow tyres and the legal speed limit.
l As your vehicle is equipped with a tyre pres-
sure monitoring system, only MITSUBISHI
MOTORS genuine wheels should be used.
Use of another type of wheel risks air leaks and sensor damage, as it will not be possible
to install the tyre inflation pressure sensors
properly.
Refer to “Tyre pressure monitoring system (TPMS)*” on page 6-59.NOTEl The laws and regulations concerning snow
tyres (driving speed, required use, type, etc.)
vary. Find out and follow the laws and regu- lations in the area you intend to drive.
l If flange nuts are used on your vehicle,
change to tapered nuts when steel wheels are used.Tyre chains
E01002103235
If tyre chains have to be used, ensure that
they are fitted only on the drive wheels
(front) in accordance with the manufacturer’s instructions.
On 4WD vehicles in which the driving power
is distributed preferentially to the front wheels, ensure that the tyre chains are fitted on the front.
Use only tyre chains which are designed for use with the tyres mounted on the vehicle: use of the incorrect size or type of chain
could result in damage to the vehicle body.
Contact a MITSUBISHI MOTORS Author-
ized Service Point before putting on tyre chains. The max. chain height is as follows.
Tyre sizeWheel sizeMax. chain
height [mm]215/70R16
215/65R1616 x 6 1/2 J9 mm
Tyres
10-16OGAE17E2Maintenance10

NOTElThe overall width varies depending on whether the vehicle is equipped with wheel lip moldings.
To determine whether your vehicle is equipped with wheel lip moldings, refer to “Exterior” on page 1-12.

Vehicle performance
E01100304042Petrol-powered vehicles
Maximum speed
1600 models183 km/h (114 mph)2000 models2WD194 km/h (121 mph)4WD191 km/h (119 mph)Diesel-powered vehicles
Maximum speed1600 models2WD182 km/h (113 mph)4WD180 km/h (112 mph)2200 models190 km/h (118 mph)

Vehicle performance
11-06OGAE17E2Specifications11

Item
2000 models2WD4WDM/TCVTINTENSEINVITEINTENSEKerb weightWithout optional parts1,350 kg1,440 kg1,445 kgWith full optional parts1,414 kg1,453 kg1,509 kgMaximum gross vehicle weight1,970 kg, 2,035 kg*Maximum axle weight
Front1,030 kgRear1,000 kg, 1,085 kg*Maximum towable weightWith brake1,300 kgWithout brake715 kg745 kgMaximum trailer-nose weight65 kgMaximum roof load80 kgSeating capacity5 persons*
: In case of trailer towingNOTEl Trailer specifications indicate the manufacturer’s recommendation.
Vehicle weight
11-08OGAE17E2Specifications11

Diesel-powered vehicles
Item
1600 models2200 models2WD4WD4WDM/TA/TINFORMINVITEINTENSE
INSTYLEINFORM INVITEINTENSE
INSTYLEINFORM INVITEINTENSE
INSTYLE
Kerb weight
Without option-
al parts1,355 kg1,380 kg1,420 kg1,445 kg1,520 kg1,540 kgWith full option-
al parts1,377 kg1,441 kg1,442 kg1,506 kg1,542 kg1,601 kgMaximum gross vehicle weight1,980 kg, 2,050 kg *2,060 kg, 2,130 kg*Maximum axle
weightFront1,120 kgRear1,000 kg, 1,090 kg *Maximum towa-
ble weightWith brake1,400 kgWithout brake695 kg745 kg750 kgMaximum trailer-nose weight70 kgMaximum roof load80 kgSeating capacity5 persons* : In case of trailer towingNOTEl Trailer specifications indicate the manufacturer’s recommendation.

Vehicle weight
11-09OGAE17E2Specifications11

Item
CombinedUrban condi-tionsExtra-urbanconditionsCO 2 (g/km)Fuel consump-
tion (L/100 km)Fuel consump-
tion (L/100 km)Fuel consump-
tion (L/100 km)1600 models2WD1194.65.24.24WD1325.05.64.7
2200 models
INFORM
INVITE1525.87.25.0INTENSE
INSTYLE1525.87.15.0NOTEl The results given do not express or imply any guarantee of the fuel consumption of the particular vehicle.
The vehicle itself has not been tested and there are inevitably differences between individual vehicles of the same model. In addition, this vehicle may incor- porate particular modifications. Furthermore, the driver’s style and road and traffic conditions, as well as the extent to which the vehicle has been driven and the standard of maintenance, will all affect its fuel consumption.

Fuel consumption
11-14OGAE17E2Specifications11

No.ItemQuantityLubricants
Engine coolant (die-
sel-powered vehicles)
1600 models
7.4 litres [includes
0.62 litre in the re- serve tank]ALTECO Freecor DSC, BASF Glysantin Alu
Protect Premium/G30 or G33, or Brugarolas Bra- dol 497
2200 models
7.5 litres [includes
0.65 litre in the re- serve tank]MITSUBISHI MOTORS GENUINE SUPER
LONG LIFE COOLANT PREMIUM or equiva-
lent*5Automatic transmission fluid8.2 litresMITSUBISHI MOTORS GENUINE ATF-J36CVT fluid6.9 litresMITSUBISHI MOTORS GENUINE CVTF-J4*
: similar high quality ethylene glycol based non-silicate, non-amine, non-nitrate and non-borate coolant with long life hybrid organic acid tech-
nologyCAUTIONl For the automatic transmission fluid, use only the
MITSUBISHI MOTORS GENUINE ATF and for the CVT fluid, use only the MITSUBISHI MOTORS
GENUINE CVTF. Use of a different fluids could damage the transmission.No.ItemQuantityLubricants
7Manual transmission oil
5 M/T1600 models2.0 litres
MITSUBISHI MOTORS GENUINE NEW MUL-
TI GEAR OIL
API classification GL-3, SAE 75W-80
2000 models2.5 litres6 M/T1600 mod- els2WD2.6 litres4WD2.7 litres8Transfer oil0.5 litreMITSUBISHI MOTORS GENUINE Super Hy-poid Gear Oil API classification GL-5 SAE 80
9Rear differential oil0.4 litre
MITSUBISHI MOTORS GENUINE Super Hy- poid Gear
Oil API classification GL-5 SAE 80
Refill capacities
11-18OGAE17E2Specifications11