bulb MITSUBISHI CARISMA 2000 1.G Owners Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2000, Model line: CARISMA, Model: MITSUBISHI CARISMA 2000 1.GPages: 280, PDF Size: 2.32 MB
Page 73 of 280
INSTRUMENTS AND CONTROLS
4–7
Turn-signal indication lamps - greenED52A-Bb
These indication lamps blink on and off when a turn-
signal lamp is operating.
NOTE
If the blinking is too fast, the cause may be a faulty
turn-signal connection or a blown lamp bulb.
Hazard warning indication lamps - greenED30A-A
When the hazard warning lamp switch is pressed, all
turn-signal lamps will flash on and off continuously.
High-beam indication lamp - blueED51A-Aa
This indication lamp illuminates when the high beam
is used.
Low fuel indication lamp - amberED63AMEa
The indication lamp comes on when the fuel tank is
getting low. Refuel as soon as possible.
CAUTION
Do not drive with an extremely low fuel level,
running out of fuel could cause damage to the
catalytic converter.
NOTE
(1) On inclines or curves, due to the movement of
fuel in the tank, the low fuel indication lamp may
come on earlier than usual.
(2)When the engine on diesel–powered vehicles
fails to operate owing to running out of fuel, it
may sometimes be difficult to start after refuel-
ing. This is due to air entering the fuel system.
Therefore, air must be bled from the system.
(Refer to the page 8–21.)
Front fog lamp indication lamp* - greenED74B-A
This lamp illuminates while the front fog lamps are on.
Page 79 of 280
INSTRUMENTS AND CONTROLS
4–13
E11D026a
Turn/lane-change signalsEE11D-N
The turn-signal lamps flash when the switch
is operated (with the ignition switch “ON”). At
the same time, the turn signal indicator
flashes.
1-Turn-signals
When making a normal turn, use posi-
tion (1). The lever will return automati-
cally when cornering is completed.
There are times when the lever will not
return after cornering. This occurs
when the steering wheel is turned only
slightly.
In such cases, return the lever by
hand.
2-Lane-change signals
When changing lanes, use position
(2). It will return to the neutral position
when released.NOTE
If the lamp flashes unusually quickly, the bulb
in a turn–signal lamp may have burned out.
Have the vehicle inspected by an authorized
MITSUBISHI dealer.
E01G011a
Headlamp levelling switchEE01GMF
The angle of the headlamp beam varies
depending upon the load carried by the ve-
hicle.
The headlamp levelling switch can be
used to adjust the headlamp illumination
distance (when the lower beam is illumi-
nated) so that the headlamps’ glare does
not distract the drivers of approaching ve-
hicles. Set the switch (referring to the fol-
lowing table) to the appropriate position
according to the number of people and the
load in the vehicle.
Page 201 of 280
For emergencies
If the vehicle breaks down 8–2. . . . . . . . . . . . . . . . .
Operation under adverse driving conditions 8–2. .
Tools and jack 8–3. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jacking up the vehicle 8–4. . . . . . . . . . . . . . . . . . . . .
Spare wheel 8–6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel covers* 8–8. . . . . . . . . . . . . . . . . . . . . . . . . . . .
If a tyre is punctured 8–9. . . . . . . . . . . . . . . . . . . . . .
Towing 8–12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine overheating 8–15. . . . . . . . . . . . . . . . . . . . . . .
Emergency starting 8–17. . . . . . . . . . . . . . . . . . . . . .
Bleeding the fuel system
(diesel-powered vehicles only) 8–21. . . . . . . . . . . . .
Removal of water from the fuel filter
(diesel-powered vehicles only) 8–21. . . . . . . . . . . . .
What to do if the engine speed becomes
unstable after the battery is replaced: 8–22. . . . . .
Fuses 8–22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing a fuse 8–25. . . . . . . . . . . . . . . . . . . . . . . . .
Replacement of lamp bulbs 8–26. . . . . . . . . . . . . . .
Page 226 of 280
FOR EMERGENCIES
8–26
N29C001a
5. Insert a new fuse of the same capacity
into the clip and insert the fuse at the
same place in the fuse box.
CAUTION
(1) If the newly inserted fuse blows
again after a short time, have the
electrical system checked and re-
paired by an authorized MITSUBI-
SHI dealer to find the cause and
rectify it.
(2) Never use a fuse with a capacity
larger than that specified or any
substitute, such as wire, foil, etc.;
doing so will cause the circuit wir-
ing to heat up and could cause
fire.
Replacement of lamp bulbsEN10A-Ab
Before replacing a bulb, ensure the lamp is
off. Do not touch the glass part of the new
bulb with your bare fingers; the skin oil left on
the glass will evaporate when the bulb gets
hot and the vapor will condense on the re-
flector and dim the surface.
N10B296a
Bulb capacityEN10BMDh
A bulb should only be replaced with a new
bulb of the same rating and type. The desig-
nation can be found on the base of the bulb.
Outside
1-Position lamps 4W (T4W). . . . . . . . .
2-Headlamps, High/low beam
60/55W (H4) . . . . . . . . . . . . . . . . . . . .
3-Front turn - signal lamps
21W (PY21W) . . . . . . . . . . . . . . . . . .
4-Side turn - signal lamps
5W (WY5W) . . . . . . . . . . . . . . . . . . . .
5-Front fog lamps* 55W (H3). . . . . . . .
Page 228 of 280
FOR EMERGENCIES
8–28
N10C123a
Headlamps
Unhook the spring which secures the bulb,
and then remove the bulb.
N10C086a
CAUTION
Never hold the halogen lamp bulb
with a bare hand, dirty glove, etc.
The oil from your hand could cause
the bulb to break the next time the
headlamps or position lamps are op-
erated.
If the glass surface is dirty, it must be
cleaned with alcohol, paint thinner,
etc., and refit it after drying it thor-
oughly.
N10C048a
Position lamps
Remove the lamp socket by turning it
anti clockwise, then pull out the bulb from the
socket.
Page 229 of 280
FOR EMERGENCIES
8–29
N10F055a
Front turn–signal lamps
Petrol–powered vehicles,
Diesel–powered vehicles (right side)
EN10FANc
Turn the bulb socket anticlockwise to re-
move. And remove the bulb from the socket
by turning anticlockwise while pressing it in-
ward.
N10F054a
Diesel–powered vehicles
(left side)
1. Remove the cover.
N10F048a
2. Turn the bulb socket anticlockwise to
remove it. And remove the bulb from
the socket by turning anticlockwise
while pressing it inward.
Page 230 of 280
FOR EMERGENCIES
8–30
N10E002a
Side turn - signal lampsEN10E-Gd
Insert a straight blade (or minus) screwdriver
at the edge of the lens, remove the socket
assembly and bulb together by turning it anti-
clockwise, and then remove the bulb by pul-
ling out.
NOTEWrap a piece of cloth around the straight
blade (or mines) screwdriver in order to
avoid scratching the lens and the body.
N10X035a
Front fog lamps*EN10X - Oc
Remove the cover mounting screw.
N10X036a
Remove bolts (1) and (2) with a screwdriver,
and pull the lamp body towards you.
NOTE
Do not turn the aiming adjusting bolt (3).
Page 231 of 280
FOR EMERGENCIES
8–31
N10X039a
Remove the connector secured at the
bracket.
N10X037a
Undo the lamp cover while pressing on the
lugs, then disconnect the connector.
N10X038a
Unhook the spring which secures the bulb
and then remove the bulb.
Page 232 of 280
FOR EMERGENCIES
8–32
N10X079a
CAUTION
Never hold the halogen lamp bulb
with a bare hand, dirty glove, etc.
The oil from your hand could cause
the bulb to break the next time the
front fog lamps are operated.
If the glass surface is dirty, it must be
cleaned with alcohol, paint thinner,
etc., and refit after drying it thorough-
ly.
N10I088a
Rear combination lampsEN10IAJa
HatchbackRemove the lid.
Turn the bulb socket anti-clockwise to re-
move it. And remove it anti-clockwise while
pressing it inward.
1-Tail lamp
2-Rear turn-signal lamp
3-Stop lamp
N10I047a
SedanTurn and remove the knob (1) and then turn
down the cover.
Page 233 of 280
FOR EMERGENCIES
8–33
N10I089a
Turn the bulb socket anti-clockwise to re-
move it. And remove the bulb from the
socket by turning it anticlockwise while pres-
sing it inward.
1-Rear turn-signal lamp
2-Stop and tail lamp
3-Tail lamp
LHD
N10K020a
Rear lid lampEN10K - Pc
HatchbackRemove the cover with a screwdriver. Turn
the bulb socket anti-clockwise to remove it.
And remove the bulb from the socket by turn-
ing it anti-clockwise while pressing it inward.
1-Reversing lamp
2-Rear fog lamp
RHD
N10K021a