child seat MITSUBISHI ECLIPSE 2012 4.G User Guide

2-24 Seat and restraint systems
2
SRS warning light
N00408700049
This warning light tells you if there is a problem involving the
SRS air bags and the pre-tensioner seat belts. Refer to “SRS
warning light” on page 2-44.Force limiter system
N00408900070
In the event of an accident, the seat belt force limiter system
will help reduce the force applied to the driver and front seat
passenger.
Child restraints
N00407100600
When transporting infants or small children in your vehicle, an
appropriate child restraint system must always be used. This is
required by law in the U.S. and Canada.
Child restraints specifically designed for infants and small chil-
dren are offered by several manufacturers. Choose only a child
restraint system with a label certifying that it complies with
Federal Motor Vehicle Safety Standard 213 (FMVSS 213) or
Motor Vehicle Restraint Systems and Booster Cushions Safety
Regulations (RSSR). Look for the manufacturer’s statement of
compliance on the box and child restraint itself.
The child restraint system should be appropriate for your
child’s weight and height, and should properly fit your vehi-
cle’s seat.
For detail information, refer to the instruction manual accom-
panying the child restraint system.Guidelines for child restraint system selectionAll children should be properly restrained in a restraint device
that offers the maximum protection for their size and age.
Be sure to check local, state, or provincial requirements for
child size and age that may vary from the recommendations
listed below.

Children less than 1 year old and children less than 20
pounds (9 kg) MUST ride in a rear-facing child safety seat
that MUST ONLY be used in the rear seat.

Children older than 1 year of age and who weigh less than
40 pounds (18 kg) or who are less than 40 inches (100 cm)
tall must be in a forward-facing restraint used only in the
rear seat.
BK0132701US.book 24 ページ ２０１０年１２月６日　月曜日　午後２時３分

Seat and restraint systems
2-25
2

Children who weigh more than 40 pounds (18 kg) or who
are more than 40 inches (100 cm) tall, regardless of age,
should use a suitable child seat or a booster seat (including
a booster cushion) in the rear seat until the vehicle’s
lap/shoulder belt fits them properly.
WA R N I N G
!
All children must be seated in the rear seat, and
properly restrained.
Accident statistics show that children of all sizes and
ages are safer when properly restrained in the rear
seat, rather than in the front seat.
Any child who is too large to use a child restraint
should ride in the rear seat and wear the lap and
shoulder belt properly. The shoulder belt must be
positioned over the shoulder and across the chest,
not across their neck, and with the lap belt posi-
tioned low on the child’s hips, not across their stom-
ach. If necessary, a booster seat (including a booster
cushion) should be used to help achieve a proper
seat belt fit. Follow the booster seat (including a
booster cushion) manufacturer’s instructions. Only
use a booster seat (including a booster cushion) that
is certified as complying with Federal Motor Vehicle
Safety Standards or Motor Vehicle Restraint Sys-
tems and Booster Cushions Safety Regulations.
Your ECLIPSE SPYDER is not equipped with a
tether anchor. Child restraint systems and a booster
seat (including a booster cushion) which require a
tether strap cannot be used in your ECLIPSE SPY-
DER.
Never operate the electric convertible top when a
child is in your ECLIPSE SPYDER or when a child
restraint system is attached to the rear seat.

Never hold an infant or child in your arms or on
your lap when riding in this vehicle, even when you
are wearing your seat belt. Never place any part of
the seat belt you are wearing around an infant or
child. Failure to follow these simple instructions cre-
ates a risk of serious injury or death to your child in
the event of an accident or sudden stop.
WA R N I N G
!
BK0132701US.book 25 ページ ２０１０年１２月６日　月曜日　午後２時３分

2-26 Seat and restraint systems
2
WA R N I N G
!
Your vehicle is also equipped with a front passenger
air bag.
Never put REAR-FACING CHILD RESTRAINTS
or INFANT RESTRAINTS in the front passenger
seat. This places the infant too close to the passenger
air bag. During deployment of the air bag, the infant
can be seriously injured or killed. Rear-facing child
restraints or infant restraints must only be used in
the rear seat.
Air bag cover
WA R N I N G
!
FRONT-FACING CHILD RESTRAINTS should
always be used in the rear seat whenever possible. If
one must be used in the front passenger seat, move
the seat to the most rearward position and make
sure the child stays in the child restraint, properly
restrained. Failure to follow these instructions could
result in serious injury or death to the child.
BK0132701US.book 26 ページ ２０１０年１２月６日　月曜日　午後２時３分

Seat and restraint systems
2-27
2
NOTE
Before purchasing a child restraint system, try installing it
in the rear seat to make sure there is a good fit. Because of
the location of the seat belt buckles and the shape of the
seat cushion, it may be difficult to securely install some
manufacturer’s child restraint systems.
If the child restraint system can be pulled forward or to
either side easily on the seat cushion after the seat belt has
been tightened, choose another manufacturer’s child
restraint system.
Depending on the seating position in the vehicle and the
child restraint system that you have, the child restraint can
be attached using one of the following two methods:
• To the lower anchorage in the rear seat ONLY if the
child restraint is compatible with the LATCH system
(See page 2-28).
• To the seat belt (See page 2-31).
WA R N I N G
!
It is important to use an approved rear-facing infant
restraint until the infant is one year old (unless the
infant outgrows the seat sooner). This allows the
infant’s neck and spine to develop enough to support
the weight of their head in the event of an accident.
When installing a child restraint system, follow the
instructions provided by the manufacturer and fol-
low the directions in this manual. Failure to do so
can result in serious injury or death to your child in
an accident or sudden stop.
After installation, push and pull the child restraint
system back and forth, and side to side, to see that it
is firmly secured. If the child restraint system is not
installed securely, it may cause injury to the child or
other occupants in the event of an accident or sud-
den stop.
When not in use, keep your child restraint system
secured with the seat belt, or remove it from the
vehicle, in order to prevent it from being thrown
around inside the vehicle during an accident.
BK0132701US.book 27 ページ ２０１０年１２月６日　月曜日　午後２時３分

2-28 Seat and restraint systems
2
Installing a child restraint system using the
LATCH (Lower Anchors and Tethers for chil-
dren) system
N00418800043
Lower anchor locationsThe seating positions in the rear seat of your vehicle are
equipped with lower anchors for attaching child restraint sys-
tems compatible with the LATCH system.NOTE
The symbols on the seatback show the location of the
lower anchor points.
Tether anchor locations (ECLIPSE only)
N00418900086
Your vehicle has 2 attachment points on the floor of the cargo
area. These are for securing a child restraint system tether strap
to each of the 2 rear seating positions in your vehicle.*- Rear of the vehicle
BK0132701US.book 28 ページ ２０１０年１２月６日　月曜日　午後２時３分

Seat and restraint systems
2-29
2
Examples of child restraint systems compatible with the
LATCH system
N00419000101
Using the LATCH system
N00419100203
1. Push the anchor connectors (A) on the child restraint sys-
tem into the slits (B) in accordance with the instructions
provided by the child restraint system manufacturer.
Remember, the lower anchors (E) provided with your
vehicle are designed to secure suitable child restraint sys-
tems compatible with the LATCH system in the rear seat
only.
A- Rear-facing child restraint
B- Front-facing child restraint
C- Child restraint system lower anchor connectors
D- Tether strap
(These are only examples.)
A: Connector
B: Slit
C: Vehicle seatback
D: Vehicle seat cushion
E: Lower anchor
BK0132701US.book 29 ページ ２０１０年１２月６日　月曜日　午後２時３分

2-30 Seat and restraint systems
2
NOTE
In order to secure a child restraint systems compatible
with the LATCH system, use the lower anchor points in
the rear seat. It is not necessary to use the vehicle’s seat
belt.2. Open the rear hatch. Remove the rear shelf panel. Refer to
“Rear shelf panel” on page 3-178.
3. Cut out the notch (F) in the cargo floor carpet by hand,
then lift the carpet.
WA R N I N G
!
If there is any foreign material in or around the
lower anchors, remove it before installing the child
restraint system. Also, make sure the seat belt is
away from, not looped through or otherwise inter-
fering with, the child restraint system. If foreign
matter is not removed and/or the seat belt interferes
with the child restraint system, the child restraint
system will not be secured properly, could detach
and move forward in the event of sudden braking or
an accident, and could result in injury to the child or
other vehicle occupants.
When the vehicle is moving, do not adjust the seat
where the child restraint system is installed.
In an ECLIPSE, install a tether strap in accordance with steps 2 to
4 shown hereafter.
* - Rear of the vehicle
BK0132701US.book 30 ページ ２０１０年１２月６日　月曜日　午後２時３分

Seat and restraint systems
2-31
2
4. Latch the tether strap hook (G) of the child restraint sys-
tem to the tether anchor (H) and tighten the tether strap so
it is securely fastened.NOTE
When using a child restraint system that requires a tether
strap, the rear shelf panel cannot be installed.
5. Push and pull the child restraint system in all directions to
be sure it is firmly secured.
Installing a child restraint system using the seat
belt (With emergency/automatic locking mecha-
nism)
N00407300413
With the exception of the driver, the seat belt in all other seat-
ing positions can be converted from normal Emergency Lock-
ing Retractor (ELR) mode to Automatic Locking Retractor
(ALR) mode. This means that when you pull the seat belt fully
out of the retractor, the retractor will switch to its ALR child
restraint installation function. Always use the ALR child
restraint installation function when you install a child restraint
system using the seat belt.
Children 12 years old and under should always be restrained in
the rear seat, whenever possible, although the front passenger
seat belt can also be converted to ALR mode.
WA R N I N G
!
Child restraint tether anchors are designed only to
withstand loads from correctly fitted child restraint
systems. Under no circumstances are they to be used
for adult seat belts, or harnesses, or for attaching
other items or equipment to the vehicle.
WA R N I N G
!
When you install a child restraint system using the
seat belt, always make sure the retractor has been
switched to the ALR child restraint installation
function. The ALR function will keep the child
restraint system tightly secured to the seat.
Failure to convert the retractor to the ALR function
may allow the child restraint system to move for-
ward during sudden braking or an accident, result-
ing in serious injury or death to the child or other
occupants.
[ECLIPSE SPYDER only]
Before attaching a child restraint system to the front
passenger seat, insert the seat belt into the seat belt
guide. Refer to “Seat belt guide” on page 2-20.
BK0132701US.book 31 ページ ２０１０年１２月６日　月曜日　午後２時３分

2-32 Seat and restraint systems
2
Installation: 1. Place the child restraint system in a rear seating position.
2. Route the seat belt through the child restraint system
according to the instructions provided by the child
restraint manufacturer. Then insert the seat belt latch plate
into the buckle. Make sure you hear a “click” when you
insert the latch plate into the buckle.3. To activate the ALR child restraint installation function,
slowly pull the shoulder part of the belt all the way out of
the retractor until it stops. Then let the belt feed back into
the retractor.
4. After the belt has retracted, tug on it. If the belt is in the
ALR function, you will not be able to pull it out. If the
webbing can be pulled out from retractor, the ALR func-
tion has not been activated and you will need to repeat
steps 3 and 4.
BK0132701US.book 32 ページ ２０１０年１２月６日　月曜日　午後２時３分

Seat and restraint systems
2-33
2
5. After confirming that the belt is locked, grab the shoulder
part of the belt near the buckle and pull up to remove any
slack from the lap part of the belt allowing the slack to
feed into the retractor. Remember, if the lap belt portion is
not tight, the child restraint system will not be secure. It
may help to put your weight on the child restraint system
and/or push on its seatback while pulling up on the belt
(see illustration). 6. Open the rear hatch. Remove the rear shelf panel. Refer to
“Rear shelf panel” on page 3-178.
7. Cut out the notch (A) in the cargo floor carpet by hand,
then lift the carpet.In an ECLIPSE, if your child restraint system requires the use of
a tether strap fasten the tether strap in accordance with steps 6 to
8 shown hereafter.
* - Rear of the vehicle
BK0132701US.book 33 ページ ２０１０年１２月６日　月曜日　午後２時３分