ignition MITSUBISHI ECLIPSE CROSS 2018 (in English) Repair Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2018, Model line: ECLIPSE CROSS, Model: MITSUBISHI ECLIPSE CROSS 2018Pages: 417, PDF Size: 74.06 MB
Page 219 of 417

Multi-information display 5-140 Features and controls
5
N00519201303
The tachometer shows engine revolutions per minute. This allows the driver to determinethe most efficient selector position and engine speed combinations. This gauge also assist
s in evaluating engine
performance.
N00554901293
Each time you press this button, there is asound and the brightness of the instrumentschanges.
N00555001419
The multi-information display displays warn- ings, the odometer, trip odometer, service reminder, engine coolant temperature, fuelremaining, outside temperature, selector lever position, average and instant fuel consump- tion, driving range, average speed, etc. It is also possible to change elements such as the language and units used on the multi- information display.
Tachometer
CAUTION The red zone indicates an engine speed beyond the range of safe operation. Select the correct selector position to control the engine speed so that the tachometer indi- cator does not enter the red zone.
Meter illumination control 1- Brightness level 2- Rheostat illumination button
NOTE
You can adjust to 8 different levels for when the front side-marker lights are illuminatedand when they are not. If the vehicle is equipped with the automatic light control, the light switch is in a position other than the “OFF” position and it is suffi- ciently dark outside the vehicle, the meterillumination switches automatically to the adjusted brightness.
The brightness level of the instruments is stored when the ignition switch is turned to the “OFF” position or the operation mode is put in OFF. If you press and hold the button for longer than approximately 2 second when the front side-marker lights are illuminated, thebrightness level changes to the maximum level. Pressing and holding the button for longer than approximately 2 second againreturns the brightness level to the previous level. On vehicles equipped with Smartphone LinkDisplay Audio, the map screen color may not be switched to nighttime setting when the meter illumination brightness level is at themaximum.
Multi-information display
NOTE
BK0252700US.book
140 ページ 2017年10月4日 水曜日 午後4時54分
Page 220 of 417
![MITSUBISHI ECLIPSE CROSS 2018 (in English) Repair Manual Multi-information display
Features and controls 5-141
5
[With ignition switch or operation mode in OFF] 1-
Warning display screen
P.5-146
2- Information screen
P.5-143
Interrupt displ MITSUBISHI ECLIPSE CROSS 2018 (in English) Repair Manual Multi-information display
Features and controls 5-141
5
[With ignition switch or operation mode in OFF] 1-
Warning display screen
P.5-146
2- Information screen
P.5-143
Interrupt displ](/img/19/34869/w960_34869-219.png)
Multi-information display
Features and controls 5-141
5
[With ignition switch or operation mode in OFF] 1-
Warning display screen
P.5-146
2- Information screen
P.5-143
Interrupt display screen
P.5-146
3- Door ajar warning display screen
P.5-147
4- Odometer
P.5-148
5-
“ ” mark indicator
P.5-146
BK0252700US.book
141 ページ 2017年10月4日 水曜日 午後4時54分
Page 221 of 417
![MITSUBISHI ECLIPSE CROSS 2018 (in English) Repair Manual Multi-information display 5-142 Features and controls
5
[With ignition switch or operation mode in ON]
N00555101234
Each time the multi-information display switches are operated, the buzzer sounds and MITSUBISHI ECLIPSE CROSS 2018 (in English) Repair Manual Multi-information display 5-142 Features and controls
5
[With ignition switch or operation mode in ON]
N00555101234
Each time the multi-information display switches are operated, the buzzer sounds and](/img/19/34869/w960_34869-220.png)
Multi-information display 5-142 Features and controls
5
[With ignition switch or operation mode in ON]
N00555101234
Each time the multi-information display switches are operated, the buzzer sounds andthe multi-information display changes
1- S-AWC drive mode display screen (if
so equipped)
P.5-69
2-
Warning display screen
P.5-146
3- Lane Departure Warning (LDW) dis-
play screen (if so equipped)
P.5-115
4- ECO mode indicator display screen
P.5-198
5- Information screen
P.5-143
6- Selector lever position display
P.5-63
7- Engine coolant temperature display
P.5-147
8- Odometer
P.5-148
9- Cruise control display screen
P.5-84
10- Adaptive Cruise Control System (ACC)
display screen (if so equipped) P.5-88
11- ECO indicator
P.5-151
12-
“ ” mark indicator
P.5-146
13- Fuel remaining display screen
P.5-147
14- Outside temperature display screen
P.5-148
NOTE
The fuel units, outside temperature units, display language, and other settings can be changed. Refer to “Changing the function settings” on page 5-152.
Multi-information display switches
BK0252700US.book
142 ページ 2017年10月4日 水曜日 午後4時54分
Page 222 of 417

Multi-information display
Features and controls 5-143
5
between information such as warnings, trip odometer, average and instant fuel consump- tion, distance range. It is also possible to
change elements such as
the language and units used on the multi- information display by operating the multi- information display switches.
N00555301207
Press the switch to display the information screen. Then, press the switch or switch to switch the display screen in the fol
lowing order.
Information screen (With the ignition switch in “OFF” position or the operation mode in OFF) *: When there is a warning display 1-
Trip odometer
P.5-148
BK0252700US.book
143 ページ 2017年10月4日 水曜日 午後4時54分
Page 223 of 417

Multi-information display 5-144 Features and controls
5
N00555801260
When the ignition switch is turned to the
“ON” position or the operation mode is put
in ON, the display screen switches in the
following order.
2-
Trip odometer
P.5-148
3- ECO score display
P.5-152
4- Service reminder
P.5-148
5- Redisplay of a warning display screen
P.5-146
Information screen (With the ignition switch is turned from the “OFF” position to the “ON” position or the operation mode is changed from OFF to ON) * : When the inspection time has arrived 1- Screen when the ignition switch or the operation mode is OFF 2- System check screen
P.5-150
3- Screen when the ignition switch or the operation mode is ON4- Service reminder
P.5-148
BK0252700US.book
144 ページ 2017年10月4日 水曜日 午後4時54分
Page 224 of 417

Multi-information display
Features and controls 5-145
5
N00556201261
Press the switch or switch to switch the display screen in the following order.Information screen (With the ignition switch or the operation mode in ON) * : When there is a warning display 1-
Trip odometer
P.5-148
2-
Trip odometer
P.5-148
3- Driving range display
P.5-150
ECO drive assist display
P.5-151
4- Average fuel consumption display
P.5-150 ECO drive assist display
P.5-151
5- Average speed display
P.5-151
Instant fuel consumption display
P.5-151
6- ECO score display
P.5-152
7- S-AWC operation display (if so
equipped)
P.5-69
8- Service reminder
P.5-148
9- Function setting screen
P.5-152
10- Redisplay of a warning display screen
P.5-146
NOTE
While driving, the service reminder are not displayed even if you operate the multi-information display switches. Always stop the vehicle in a safe place before operating.
BK0252700US.book
145 ページ 2017年10月4日 水曜日 午後4時54分
Page 226 of 417

Multi-information display
Features and controls 5-147
5
N00529700043
If any of the doors or the liftgate is not com- pletely closed, this displays the open door orliftgate. If the speed increases to approximately 5 mph (8 km/h) or higher with a door ajar, a tonewill sound four times to inform you that a door is ajar.
N00578200020
Shows the engine coolant temperature. If the coolant becomes hot, “ ” will blink. Pay careful attention to the engine coolant temperature display while you are driving.
N00556601210
Shows the amount of fuel remaining.
NOTE
When the warning is displayed, the warn- ing display screen can be redisplayed on the information screen. Refer to “Information screen (with the igni-tion switch in “OFF” position or the opera- tion mode in OFF)” on page 5-143. Refer to “Information screen (with the igni-tion switch or the operation mode in ON)” on page 5-145.
Door ajar warning display screen
CAUTION Always make sure that the warning display goes out before beginning to drive.
Engine coolant temperature display
CAUTION If the engine is overheating, “ ” will blink. In this case, the bar graph is on the red zone. Immediately park the vehicle in a safe placeand take the required measures. Refer to “Engine overheating” on page 8-4.
Fuel remaining display screen
F- Full E- Empty
CAUTION Running out of gas could damage the cata- lytic converter. If the warning display appears, refuel as soon as possible.NOTE
It may take several seconds to stabilize the display after refilling the tank. If fuel is added with the ignition switch or the operation mode in ON, the remaining fuel display may incorrectly indicate the fuel level. The arrow (A) indicates that the fuel tank filler door is located
on the left side of the
vehicle. (Refer to “Filling the fuel tank” on page 3-3.)
BK0252700US.book
147 ページ 2017年10月4日 水曜日 午後4時54分
Page 228 of 417

Multi-information display
Features and controls 5-149
5
1. Shows the time until the next periodic inspection. 2. This informs you that a periodic inspec- tion is due. Contact an authorized Mitsubishi Motors dealer or a repair facil-ity of your choice to have the system checked.
At that time, when the ignition switch is switched from the “OFF” position to the “ON” position or the operation mode ischanged from OFF to ON, the warning display is displayed for a few seconds on the information screen. 3. After your vehicle is inspected at an authorized Mitsubishi Motors dealer, it displays the time until the next periodic inspection.
The “---” display can be reset while the igni- tion switch or the operation mode is in OFF.When the display is reset, the time until the next periodic inspection is displayed and the warning display is no longer displayed whenthe ignition switch is switched from the “OFF” position to the “ON” position or the operation mode is changed from OFF to ON. 1. When you press the switch or switch, the information screen switches to the service reminder display screen.
2. Press and hold the switch (for approxi- mately 2 seconds or
more) to display “ ”
and make it flash. (If there is no operation for approximately 10 seconds with this indicator flashing, the display returns tothe previous screen.) 3. With this indicator flashing, if you press the switch, the screen switches from “- --” to “CLEAR”. After that, the time until the next periodic inspection is shown.
NOTE
The service reminder time can be modified by an authorized Mitsubishi Motors dealer, to adjust for severe usage, etc. Refer to “Severe maintenance schedule” in your vehi- cle’s Warranty and Maintenance Manual. Forfurther information, please contact your authorized Mitsubishi Motors dealer.NOTE
Shows the distance in units of 100 miles (100 km) and the time in units of 1 month.
To r e s e t
BK0252700US.book
149 ページ 2017年10月4日 水曜日 午後4時54分
Page 229 of 417

Multi-information display 5-150 Features and controls
5
N00578400048
When the ignition switch is turned to the “ON” position or the operation mode is put in ON, the system check screen is displayed forapproximately 4 seconds. If there is no fault, the information screen is displayed. If there is a fault, the screen changes to warn-ing display.
Refer to “Warning display list” on page 5-162.
N00575201026
Shows the approximate driving range (how many more miles or kilometers you can drive). When this driving range falls below30 miles (50 km), “---” is displayed. Refuel as soon as possible.
N00575301027
This displays the average fuel consumptionfrom the last reset to the present. There are 2 types of mode settings of manualreset and automatic reset. Refer to “Changing the reset mode for aver- age fuel consumption and average speed” onpage 5-154. For information on how to change the aver- age fuel consumption display setting, refer to“Changing the function settings” on page 5-152.
CAUTION The customer is responsible for making sure that regular inspections and maintenance and periodic inspections and maintenance are performed. Inspections and maintenance must be per-formed to prevent accidents and malfunc- tions.NOTE
The “---” display cannot be reset while the ignition switch or the operation mode is in ON. When “---” is displayed, after a certain dis- tance and a certain period of time, the dis- play is reset and the time until the nextperiodic inspection is displayed. If you accidentally reset the display, consult an authorized Mitsubishi Motors dealer for assistance.
System check screen
Driving range display
NOTE
The driving range is determined based on the fuel consumption data. This may vary depending on the driving conditions and hab- its. Treat the distance displayed as just arough guideline. When you refuel, the driving range display is updated. However, if you only add a small amount of fuel, the correct value will not be displayed.Fill to a full tank whenever possible. When your vehicle is stopped on an extremely steep hill, the driving range value may, change. This is due to the movement of fuel in the tank and does not indicate anybreakdown.
The display setting can be changed to the preferred units (miles or km). Refer to “Changing the function settings” on page 5-152.
Average fuel consumption dis- play
NOTE
The average fuel consumption display can be reset separately in both auto reset mode and manual reset mode. “---” is displayed when the average fuel con- sumption cannot be measured. The initial (default) setting is “Auto reset mode”.NOTE
BK0252700US.book
150 ページ 2017年10月4日 水曜日 午後4時54分
Page 231 of 417

Multi-information display 5-152 Features and controls
5
N00578800055
ECO score indicates the points you have scored on fuel-efficient driving by the num- ber of leaves as follows: [When the ignition switch or the operation mode is ON]The display shows the score you achieved in the last several minutes.
[When the ignition switch is turned to the “OFF” position or the operation mode is put in OFF] The display shows the overall ECO score thefunction has counted from the time when the ignition switch is turned to the “ON” position to the time when it is turned to the “OFF” or“ACC” position, or from the time when the operation mode is set to ON to the time when it is set to OFF.
N00556801283
1. Park your vehicle in a safe place.Firmly apply the parking brake and movethe selector lever into the “P” (PARK) position. 2. When you press
the switch or
switch, the information screen switches to the function setting screen.
Refer to “Information screen” on page 5-145. 3. Press the switch to switch to the top screen (A) for the menu screens. Then, press the switch or switch to switch to the menu screens (B).
NOTE
The ECO drive assist is displayed only when vehicle is driven with the selector lever in the “D” (DRIVE) position or when vehicle isdriven in the sport mode (for vehicles equipped with sportronic steering wheel pad- dle shifter).
ECO Score
ECO drive level
Low High
Changing the function settings
ECO drive level Low High
CAUTION For safety, stop the vehicle before operating. While driving, even if you operate the multi- information display switches ( , , ), the function setting scr
een is not displayed.
BK0252700US.book
152 ページ 2017年10月4日 水曜日 午後4時54分