lock MITSUBISHI ENDEAVOR 2011 1.G Manual PDF

3-138 Features and controls
3
NOTE
The initial (default) setting is “C”.
2. The monitor will show “The setting is progressing” while
the setting change is in progress.
When the setting change has been completed successfully,
the tone will sound once and the monitor will return to the
“Dome light shutoff time” display.
If the setting change is not successful, the monitor will
show “The setting failed.” then return to the “Dome light
shutoff” display.
Interior light auto-shutoff time
N00535700064
It is possible to change the period that elapses until each inte-
rior light whose switch is in the “ON” position automatically
goes off when the ignition key is turned from the “ON” posi-
tion to the “LOCK” or “ACC” position.
1. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• A: 3 minutes
• B: 30 minutes
• C: 60 minutes
• D: No auto-shutoff
(Interior light auto-shutoff does not take place.)NOTE
The initial (default) setting is “B”.
BK0121600US.book 138 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

3-142 Features and controls
3
Keyless entry system & power door lock system customi-
zation
N00534700038
1. Display “Keyless entry system & power door lock sys-
tem” on the monitor in accordance with “Basic operation”
(see page 3-109), align the cursor with it, and press the
“SELECT” function button.2. Press the “ ” function button, align the cursor with the
function you wish to change, and press the “SELECT”
function button.
BK0121600US.book 142 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

Features and controls
3-143
3
• “Keyless entry system confirmation by horn” → P. 3 - 1 4 3
• “Keyless entry system confirmation by turn signal
lights” → P. 3 - 1 4 3
• “Keyless entry automatic relocking time” → P. 3 - 1 4 5
• “Unlock operation using keyless entry system or door
key” → P. 3 - 1 4 6
Keyless entry system confirmation by horn
N00536000093
It is possible to change the confirmation function provided by
the horn when the keyless entry system is used to lock the
doors.
1. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• A: The horn sounds when the doors and the liftgate are
locked.
• B: When a lock operation has been performed, the horn
sounds when the “LOCK” button is pressed again.• C: The horn does not sound.
NOTE
The initial (default) setting is “B”.
2. The monitor will show “The setting is progressing” while
the setting change is in progress.
When the setting change has been completed successfully,
a tone will sound once and the monitor will return to the
“Keyless entry system confirmation by horn” display.
If the setting change is not successful, the monitor will
show “The setting failed.” then return to the “Keyless
entry system confirmation by horn” display.Keyless entry system confirmation by turn signal lights
N00536100065
It is possible to change the confirmation function provided by
the turn signal lights when the keyless entry system is used to
lock or unlock the doors and the liftgate.
BK0121600US.book 143 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

3-144 Features and controls
3
1. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• A:The turn signal lights blink when the doors and the
liftgate are locked or unlocked.
• B:The turn signal lights blink only when the doors and
the liftgate are locked.
• C:The turn signal lights blink only when the doors and
the liftgate are unlocked.
• D:The turn signal lights do not blink.NOTE
The initial (default) setting is “A”.2. The monitor will show “The setting is progressing” while
the setting change is in progress.
When the setting change has been completed successfully,
a tone will sound once and the monitor will return to the
“Keyless entry system confirmation by turn signal lights”
display.
If the setting change is not successful, the monitor will
show “The setting failed.” then return to the “Keyless
entry system confirmation by turn signal lights” display.
BK0121600US.book 144 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

Features and controls
3-145
3
Keyless entry automatic relocking time
N00536200066
It is possible to change the time that elapses before automatic
relocking when the keyless entry system has been used to
unlock and no doors and the liftgate are opened.
1. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• A:30 seconds
• B:60 seconds
• C:120 seconds
• D:180 secondsNOTE
The initial (default) setting is “A”.2. The monitor will show “The setting is progressing” while
the setting change is in progress.
When the setting change has been completed successfully,
a tone will sound once and the monitor will return to the
“Keyless entry automatic relocking time” display.
If the setting change is not successful, the monitor will
show “The setting failed.” then return to the “Keyless
entry automatic relocking time” display.
BK0121600US.book 145 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

3-146 Features and controls
3
Unlock operation using keyless entry system or door key
N00536300067
It is possible to change the door(s) and the liftgate that will be
unlocked when an unlock operation is performed using the
keyless entry system or when the driver’s door is unlocked
using the key.1. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.BK0121600US.book 146 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

Features and controls
3-147
3
• A:A single unlock operation unlocks only the driver’s
door.
Two unlock operations unlock all of the doors and the
liftgate.
• B:A single unlock operation unlocks all of the doors and
the liftgate.
NOTE
The initial (default) setting is “A”.
2. The monitor will show “The setting is progressing” while
the setting change is in progress.
When the setting change has been completed successfully,
a tone will sound once and the monitor will return to the
“Unlock operation using keyless entry system or door
key” display.
If the setting change is not successful, the monitor will
show “The setting failed.” then return to the “Unlock
operation using keyless entry system or door key” display.
Buzzers customization
N00534900056
1. Display “Buzzers” on the monitor in accordance with
“Basic operation” (see page 3-109), align the cursor with
it, and press the “SELECT” function button.
BK0121600US.book 147 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

3-154 Features and controls
3
[When the engine is started and the parking brake is released]
The daytime running lights come on. (if so equipped)NOTE
Once the daytime running lights (if so equipped) have
been turned on, the illuminated lights do not go off until
the ignition switch is turned to the “LOCK” or “ACC”
position.
[When the engine is not running, or the engine is running but
the parking brake has not been released]
The engine can be started with the headlights off when the
vehicle is stationary.NOTE
Do not leave the headlights and other lights on for a long
period of time when the engine is not running. The battery
will run down.
When it rains, or when the vehicle has been washed, the
inside of the lens sometimes becomes foggy. This is the
same as when window glass mists up on a humid day, and
does not indicate a problem. When the light is switched
on, the heat will dry out the fog. However, if water col-
lects inside the light, have it checked by an authorized
Mitsubishi Motors dealer or a repair facility of your
choice.
Light auto-shutoff function (headlights and other
lights)
N00532600307

If the ignition key is turned to “LOCK” or “ACC” posi-
tion or removed from the ignition switch and the driver’s
door is opened with the light switch in the “ ” or “ ”
position, the lights automatically turn off.
• If the driver’s door is opened after the key is removed
from the ignition switch, a high-pitched constant tone
will sound to remind you to turn off the lights.
• If the driver’s door is opened with the key in the ignition
switch, a low-pitched tone will sound to remind you to
remove the key.

If the ignition key is turned to “LOCK” or “ACC” posi-
tion or removed from the ignition switch with the driver’s
door closed and the light switch in the “ ” or “ ”
position, the lights will stay on for about 3 minutes and
then turn off automatically. NOTE
In vehicles with multi center display, multi center display
can be used to deactivate the light auto-shutoff function.
For details, refer to “Setting and customization” on page
3-108.
OFF Headlights illuminate dimly
Headlights illuminate dimly and
Parking, tail, front and rear side-marker lights, license
plate and instrument panel lights on
Headlights and other lights on
OFF All lights off
Parking, tail, front and rear side-marker lights, license
plate and instrument panel lights on
Headlights and other lights onBK0121600US.book 154 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

Features and controls
3-155
3
When you want to keep the lights on: If the light switch is turned to the “ ” or “ ” position again
after the engine is turned off, the 3 minute auto-shutoff func-
tion described above will not work. The lights (parking lights,
tail lights and license plate lights) will stay on and will not turn
off automatically. NOTE
In vehicles with multi center display, multi center display
can be used to keep the light on for approximately 3 min-
utes after you leave the vehicle.
For details, refer to “Setting and customization” on page
3-108.
If the light auto-shutoff function is reprogrammed, you can
activate the 3-minute auto-shutoff function as follows:
1. After turning the ignition key to the “LOCK” or “ACC”
position or removing it from the ignition switch, set the
light switch to the “OFF” position.
2. Put the light switch back to the “ ” or “ ” position
again and get out of the vehicle.
3. The light will automatically turn off after 3 minutes.NOTE
When the driver’s door is opened, a continuous high-
pitched tone will sound if the key has been removed; a
continuous low-pitched tone will sound if the key is in the
ignition switch.
The tone stops sounding when the driver’s door is closed.
Headlight reminder buzzer
N00549800125
If the driver’s door is opened with the key in the “LOCK” or
“ACC” position or removed from the ignition switch while the
lights are on, the tone will sound to remind you to turn off the
lights. The lights will turn off automatically and so will the
tone. Or you can turn the light switch to the “OFF” position to
stop the tone.
BK0121600US.book 155 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

3-162 Features and controls
3
NOTE
To ensure a clear rearward view, the wiper performs a
number of continuous operations either when the switch is
moved to the “INT” position or when the selector lever is
moved to the “R” (REVERSE) position while the switch
is in the “INT” position.
Following this continuous operation, the wiper will auto-
matically switch to intermittent operation.

In vehicles with multi center display, multi center display
can be used to adjust the time intervals of the intermittent
wiper operation.
For details, refer to “Setting and Customization” on page
3-108.

The washer fluid reservoir is located in the engine com-
partment.
Check the fluid level regularly and refill if necessary. (See
“Washer fluid” on page 7-14.)Precautions to observe when using wipers and
washers
N00523500111
NOTE
Do not use the wipers when the windshield is dry. This
could scratch the glass and wear the wiper blades prema-
turely.
Before using the wipers in cold weather, check to be sure
that the wiper blades are not frozen to the windshield or
rear window. Using the wipers while the blades are frozen
could cause the wiper motor to burn out.

If the wipers become blocked by ice or other deposits on
the glass, the motor may still burn out even if the wiper
switch is OFF. If deposits form on the windshield, park
your vehicle in a safe place, turn off the engine, and clean
the glass so that the wipers can operate smoothly.

Avoid using the washer for more than 20 seconds at a
time. Do not operate the washer when the fluid reservoir
is empty or the pump may fail.

During cold weather, add a recommended washer solution
that will not freeze in the washer reservoir. Otherwise the
washer may not work or may be damaged.

Replace the wiper blades when they are worn. Use the
proper size replacement blades. If you have questions, ask
your authorized Mitsubishi Motors dealer.
CAUTION
!
If the washer is used in cold weather, the washer
fluid sprayed onto the glass might freeze, blocking
your view. In cold weather, heat the glass with the
defroster before using the washer.
BK0121600US.book 162 ページ ２０１０年４月１２日　月曜日　午前１０時３９分