oil MITSUBISHI ENDEAVOR 2011 1.G Owners Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2011, Model line: ENDEAVOR, Model: MITSUBISHI ENDEAVOR 2011 1.GPages: 514, PDF Size: 111.98 MB
Page 12 of 514
Quick index
1
If this warning light comes on or flashes while you’re driving...
N00200700924
NOTEThese warning lights will come on for a few seconds for a bulb check when the ignition key is first turned to “ON”.
Warning light
Do this
Ref. page
Charging system warning lightPark your vehicle in a safe place and stop the engine.
Contact an authorized Mitsubishi Motors dealer or a repair facility of your
choice for assistance.P.3-85
Oil pressure warning lightPark your vehicle in a safe place and stop the engine, then check the engine
oil level.
If the light comes on while the engine oil level is normal, have the system
checked at an authorized Mitsubishi Motors dealer or a repair facility of your
choice as soon as possible.P.3-85
or
Brake warning lightIf this light comes on while driving, check to see that the parking brake is
fully released.
If this light stays on after releasing the parking brake, stop and check the
brake fluid level.
If the brake fluid level is correct, there may be a system malfunction. Avoid
hard braking and high speeds, and contact an authorized Mitsubishi Motors
dealer or a repair facility of your choice for assistance.P.3-83
BK0121600US.book 1 ページ 2010年4月12日 月曜日 午前10時39分
Page 91 of 514
3-2 Features and controls
3Break-in recommendations
N00508700255
Advanced automobile manufacturing techniques permit you to
operate your new vehicle without requiring a long break-in
period of low-speed driving.
However, you can add to the future performance and economy
of your vehicle by observing the following precautions during
the first 300 miles (500 km).
Drive your vehicle at moderate speeds during the break-in
period.
Avoid revving the engine.
Avoid rough driving such as fast starts, sudden accelera-
tion, prolonged high-speed driving and sudden braking.
These would have a detrimental effect on the engine and
also cause increased fuel and oil consumption, which
could result in malfunction of the engine components. Be
particularly careful to avoid full acceleration while in low
gear.
Do not overload the vehicle. Observe the seating capacity
(See “Cargo load precautions” on page 4-12).
Refrain from towing a trailer or other vehicle (See
“Trailer towing” on page 4-15).
Keys
N00508800474
Two keys are provided.
The keys fit all locks. Keep one in a safe place as a spare key.
BK0121600US.book 2 ページ 2010年4月12日 月曜日 午前10時39分
Page 139 of 514
3-50 Features and controls
3
Driving through water
N00537800069
If the electrical circuits become wet, further operation of the
vehicle will be impossible; therefore, avoid driving through
water unless absolutely necessary. If driving through water is
unavoidable, use the following procedure:
Check the depth of the water and the terrain before attempting
to drive through it. Drive slowly to avoid creating excessive
water splashing.
Inspection and maintenance following
rough road operation
N00530700072
After operating the vehicle in rough road conditions, be sure to
perform the following inspection and maintenance procedures:
Check that the vehicle has not been damaged by rocks,
gravel, etc.
Carefully wash the vehicle with water.
Drive the vehicle slowly while lightly depressing the
brake pedal in order to dry out the brakes. If the brakes
still do not function properly, contact an authorized Mit-
subishi Motors dealer or a repair facility of your choice as
soon as possible to have the brakes checked.
Remove the insects, dried grass, etc. clogging the radiator
core.
After driving through water, check the engine, transaxle
and differential oil. If the oil or grease is milky or cloudy
because of water contamination, it must be replaced with
new oil.
Check the inside of the vehicle. If water entry is found,
dry the carpet etc.
Inspect the headlights. If water is in the headlight housing,
have it drained at an authorized Mitsubishi Motors dealer
or a repair facility of your choice.
Have an authorized Mitsubishi Motors dealer or a repair
facility of your choice replace the grease in the wheel
bearings.
CAUTION
!Never drive through water that is deep enough to
cover wheel hubs, axles or exhaust pipe. Do not
change gears while driving through water.
Frequent driving through water can adversely affect
the life span of the vehicle; consult an authorized
Mitsubishi Motors dealer or a repair facility of your
choice and take the necessary measures to prepare,
inspect, and repair the vehicle.After driving through water, apply the brakes to be
sure they are functioning properly. If the brakes are
wet and not functioning properly, dry them out by
driving slowly while lightly depressing the brake
pedal. Inspect each part of the vehicle carefully.
BK0121600US.book 50 ページ 2010年4月12日 月曜日 午前10時39分
Page 140 of 514
Features and controls
3-51
3 Cautions on the handling of all-wheel drive
vehicles
N00530800129
Tires and wheelsSince the driving torque can be applied to the four wheels, the
driving performance of the vehicle when operating in all-wheel
drive is greatly affected by the condition of the tires.
Pay close attention to the tires.
Install only the specified tires on all wheels. Refer to
“Tires and wheels” on page 9-7.
Be sure all four tires and wheels are the same size and
type.
When it is necessary to replace any of the tires or wheels,
replace all four.
All tires should be rotated before the wear difference
between the front and rear tires is recognizable.
Good vehicle performance cannot be expected if there is a dif-
ference in wear between tires. Refer to the “Tire rotation” on
page 7-27.
Check the tire inflation pressure regularly.
CAUTION
!Always use tires of the same size, type, and brand
that have no wear differences. Using tires of differ-
ent size, type, brand or degree of wear, will increase
the differential oil temperature and result in possi-
ble damage to the driving system. Further, the drive
train will be subject to excessive loading, possibly
leading to oil leakage, component seizure, or other
serious problems.
BK0121600US.book 51 ページ 2010年4月12日 月曜日 午前10時39分
Page 171 of 514
3-82 Features and controls
3Indicator and warning light package
N00519800735
Ty p e 2 Ty p e 1
1- Engine malfunction indicator (“SERVICE ENGINE SOON”
or “Check engine light”) → P.3-84
2- Cruise control indicator → P.3-64
3- High beam indicator → P.3-83
4- Turn signal indicators/Hazard warning lights → P.3-83
5- Front fog light indicator (if so equipped) → P.3-83
6- Selector lever position indicator → P. 3 - 4 2
Sports mode indicator → P.3-45
7- Automatic transaxle fluid temperature warning light
→ P. 3 - 4 2
8- ASC indicator → P.3-60
TCL indicator → P.3-60
9- TCL OFF indicator → P. 3 - 6 0
10- Seat belt reminder/warning light → P.2-19
11- Door-ajar warning light → P.3-8512- Oil pressure warning light → P.3-85
13- Charging system warning light → P.3-85
14- Immobilizer indicator → P. 3 - 3
15- Tire pressure monitoring system warning light → P. 3 - 7 0
16- SRS warning light → P.2-24, 2-44
17- Anti-lock braking system warning light → P. 3 - 5 5
18- Brake warning light → P.3-83
19- Low-fuel warning light → P.3-80
BK0121600US.book 82 ページ 2010年4月12日 月曜日 午前10時39分
Page 174 of 514
Features and controls
3-85
3
Charging system warning light
N00520600166
This light comes on in the event of a malfunction in the charg-
ing system or when the ignition key is turned to the “ON” posi-
tion (engine off). When the engine is started, the light should
go out. Check to make sure that the light has gone out before
driving.
Oil pressure warning light
N00520700154
This light comes on when the engine oil pressure is below nor-
mal. If the light stays on while driving, stop the engine as soon
as possible. Do not run the engine until the cause of the low oil
pressure is corrected.Door-ajar warning light and buzzer
N00520900286
This light comes on when any door, the liftgate is open or not
completely closed.
When the vehicle is moving at more than 5 mph (8 km/h) and
any door, the liftgate is open or ajar, a tone will sound 4 times
and the warning light will flash 4 times to inform the driver
that any door, the liftgate is not properly shut.
CAUTION
!If the warning light stays on after the engine has
started, the battery charging system may be mal-
functioning. In this case, take your vehicle to an
authorized Mitsubishi Motors dealer or a repair
facility of your choice and have the system checked.
CAUTION
!If this light comes on when the engine oil level is not
low, have your vehicle checked at an authorized Mit-
subishi Motors dealer or a repair facility of your
choice.This warning light does not show the amount of oil
in the crankcase. This can only be determined by
checking the oil level with the dipstick with the
engine turned off.
CAUTION
!Before driving, make sure that the door-ajar warn-
ing light is off.
BK0121600US.book 85 ページ 2010年4月12日 月曜日 午前10時39分
Page 177 of 514
3-88 Features and controls
3
Controls and display
N00533100093
1- Electronic compass
This display shows the compass direction of the vehicle.
2- Digital clock → P.3-90
3- Road surface freeze warning → P.3-92
4- Outside temperature → P.3-92
5- Audio
This display shows the audio condition.
Refer to “Audio” on page 3-96.
6- Display for function buttons
This display shows the options available for each function
button.
7- Function buttons
These buttons can select the options shown in the display.8- Maintenance reminder → P. 3 - 1 1 5
It is possible to set the dates when maintenance tasks (engine
oil replacement, oil filter replacement, etc.) were last per-
formed and the driving distances before the maintenance
tasks have to be performed again.
“Record maintenance” → P. 3 - 1 1 5
9- DISP button
This button can change the display.
“Change of display” → P.3-89
“Setting and customization” → P.3-108
BK0121600US.book 88 ページ 2010年4月12日 月曜日 午前10時39分
Page 204 of 514
Features and controls
3-115
3
Record maintenance
N00501000031
For each of the following items, it is possible to set the date
when maintenance was last performed and the driving distance
until the next maintenance.
Engine oil
Oil filter
Rotate tires
Air purifier
A/T Fluid
Brake system
*
1, *2
NOTEUse *
1 and *
2 if you wish to set the dates when mainte-
nance was performed for components not shown on the
display.
Maintenance times and reminders were not set before the
vehicle left the factory, so they are initially displayed as “-
--”. To set them, follow the instructions in “Checking and
setting maintenance information” (see page 3-116)
Depending on the vehicle model and specifications, some
of the functions on the monitor may not operate.
Maintenance reminder
N00502700019
When the distance driven reaches a distance that has been set
for scheduled maintenance, the maintenance reminder (A) is
shown to indicate that the time for maintenance has come.NOTEThe maintenance reminder appears when the distance
driven reaches the distance that has been set for any one of
the maintenance items.
When the monitor has been set to give no display, the
maintenance reminder is not shown when the distance
driven reaches a distance that has been set.
BK0121600US.book 115 ページ 2010年4月12日 月曜日 午前10時39分
Page 279 of 514
3-190 Features and controls
3
NOEnglish No -
Spanish No -
French Non -
ZEROEnglish Zero Oh (letter “O” )
Spanish Cero O
French Zéro O (lettre «o»)
ONEEnglish One -
Spanish Uno Una
French Un Une
TWOEnglish Two -
Spanish Dos -
French Deux -
THREEEnglish Three -
Spanish Tres -
French Trois -
FOUREnglish Four -
Spanish Cuatro -
French Quatre -
FIVEEnglish Five -
Spanish Cinco -
French Cinq -Command
Lan-
guage
Primary Command
Alternative
Commands
SIXEnglish Six -
Spanish Seis -
French Six -
SEVENEnglish Seven -
Spanish Siete -
French Sept -
EIGHTEnglish Eight -
Spanish Ocho -
French Huit -
NINEEnglish Nine -
Spanish Nueve -
French Neuf -
STAREnglish Star (*) -
Spanish Estrella (*) Asterisco (*)
French Étoile (*) -
POUNDEnglish Pound (#) -
Spanish Número (#)Signo De Número
(#)
French Dièse (#) -Command
Lan-
guage
Primary Command
Alternative
Commands
BK0121600US.book 190 ページ 2010年4月12日 月曜日 午前10時39分
Page 303 of 514
4-4 Driving safety
4
DefrostersCheck these by selecting the defroster mode, and set the blower
switch on high. You should be able to feel the air blowing
against the windshield.
(Refer to “Defrosting or defogging the windshield and door
windows” on page 5-12, 5-23.)TiresCheck all the tires for heavy tread wear or uneven wear pat-
terns. Look for stones, nails, glass, or other objects stuck in the
tread. Look for any tread cuts or sidewall cracks. Check the
wheel nuts for tightness, and the tires (including spare tire) for
proper pressures. Replace your tires before they are heavily
worn out.
As your vehicle is equipped with a tire pressure monitoring
system, there is a risk of damage to the tire inflation pressure
sensors when the tire is replaced on the rim. Tire replacement
should, therefore, be performed only by an authorized Mitsub-
ishi Motors dealer.LightsHave someone watch while you turn all the exterior lights on
and off. Also check the turn signal indicators and high-beam
indicators on the instrument panel. Fluid leaksCheck the ground under the vehicle after parking overnight, for
fuel, water, oil, or other leaks. Make sure all the fluid levels are
correct. Also, if you can smell fuel, you need to find out why
immediately and have it fixed.
WA R N I N G
!Always properly position floor mat and assure it
does not interfere with operation of the pedals.Always use retaining clip on the driver’s floorboard
to secure the Mitsubishi genuine floor mat.Always install the mat with the correct side facing
down.Never install a second mat over an existing floor
mat.
BK0121600US.book 4 ページ 2010年4月12日 月曜日 午前10時39分