buttons MITSUBISHI GALANT 2011 9.G Owners Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2011, Model line: GALANT, Model: MITSUBISHI GALANT 2011 9.GPages: 424, PDF Size: 61.82 MB
Page 96 of 424
Features and controls
3-7
3
General informationYour electronic immobilizer operates on a radio frequency sub-
ject to Federal Communications Commission (FCC) Rules
(For vehicles sold in U.S.A.) and Industry Canada Rules (For
vehicles sold in Canada). This device complies with Part 15 of
the FCC Rules and RSS-210 of the Industry Canada Rules.
Operation is subject to the following two conditions.
This device may not cause harmful interference.
This device must accept any interference received, includ-
ing interference that may cause undesired operation.
Keyless entry system
N00509000848
Press the remote control transmitter buttons to lock or unlock
the doors and to open the trunk lid.
It can also help you signal for attention by setting off the panic
alarm.
CAUTION
!Changes or modifications not expressly approved by
the manufacturer for compliance could void the
user’s authority to operate the equipment.
1-
LOCK ( ) button
2-
UNLOCK ( ) button
3-
Trunk ( ) button
4- PANIC button
5- Indicator light
BK0121200US.book 7 ページ 2010年4月14日 水曜日 午前11時24分
Page 97 of 424
3-8 Features and controls
3
To l o c k Press the LOCK button (1) to lock all the doors.
If they are locked while the dome light is not illuminated, the
dome light will blink once. The turn signal lights will also
blink once. NOTEIf you press the LOCK button (1) after locking the doors,
the horn will sound once to confirm that they are locked.To unlock Press the UNLOCK button (2) to unlock the driver’s door only.
Press the UNLOCK button one more time to unlock all the
doors.
If the driver’s door only or all doors are unlocked while the
dome light is not illuminated, the dome light will turn on for 15
seconds. The turn signal lights will also blink twice.To open the trunk lidPress the trunk button (3) twice within 5 seconds and the trunk
lid will be opened. The trunk lid must be closed manually after
it has been opened.NOTEOn a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to a separate operation manual.Answerback function The keyless entry system answerback functions from the horn
and turn signal lights can each be turned on or off as desired.
This is done with the key removed from the ignition switch.
NOTEThe answerback function will not operate when the key is
in the ignition switch.Horn deactivation/reactivation The answerback function can be set in the following three
ways.
Each time the answerback function is set, a tone will sound to
tell you the condition of the answerback function.
1. Press the LOCK button (1) for 4 to 10 seconds and press
the UNLOCK button (2) during this time.
2. Release the LOCK and UNLOCK buttons within 10 sec-
onds of pressing the UNLOCK button in step 1.NOTEOn a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to a separate operation manual.One chime: The horn will sound if the doors are locked with
the keyless entry system.
Two chimes: The horn will not sound, even if the doors are
locked with the keyless entry system.
Three chimes: The horn will sound if the doors are already
locked and the keyless entry system is used.
In this mode, the horn will only sound when the
keyless entry LOCK button is pressed again to
reconfirm that the doors are locked.
BK0121200US.book 8 ページ 2010年4月14日 水曜日 午前11時24分
Page 98 of 424
Features and controls
3-9
3
Turn signal light deactivation/reactivation The answerback function from the turn signal lights indicating
when the doors are locked or unlocked can be turned on or off
separately.
A tone will sound once when the function has been turned on,
and twice if it has been turned off.
To deactivate/reactivate the answerback function for lock-
ing of the doors, take the following steps:
1. Press the UNLOCK button (2) for 4 to 10 seconds and
press the LOCK button (1) during this time.
2. Release the LOCK button and then release the UNLOCK
button within 10 seconds of pressing the LOCK button in
step 1.
To deactivate/reactivate the answerback function for
unlocking of the doors, take the following steps:
1. Press the UNLOCK button (2) for 4 to 10 seconds and
press the LOCK button (1) during this time.
2. Release the UNLOCK button and then release the LOCK
button within 10 seconds of pressing the LOCK button in
step 1.NOTEOn a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to a separate operation manual.
Using the panic alarmIf you are near your vehicle and feel threatened, you may acti-
vate the alarm to call attention as follows:
1. Press the PANIC button (4) for more than 1 second.
2. The headlights will blink on and off and the horn will
sound intermittently for about 3 minutes.
3. To turn off the alarm, press any button on the remote con-
trol transmitter.NOTEThe indicator light (5) comes on each time a switch is
pressed.
The keyless entry system does not work if the key is in the
ignition.
The remote control transmitter can be used from about 40
feet (12 m) away. However, this distance may change if
your vehicle is near a TV transmitting tower, a power sta-
tion, or a radio station.
If the UNLOCK button (2) is pressed and no door is
opened within approximately 30 seconds: relocking will
automatically occur.
On a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to a separate operation manual.
If the following conditions are observed after pressing one
of the buttons of the remote control transmitter, the battery
in the remote control transmitter may need to be replaced.
• The doors cannot be locked or unlocked.
• The trunk lid cannot be opened.
• The panic alarm cannot be operated.
• The indicator light (5) is dim or does not come on.
BK0121200US.book 9 ページ 2010年4月14日 水曜日 午前11時24分
Page 99 of 424
3-10 Features and controls
3
If you lose your remote control transmitter, please contact
an authorized Mitsubishi Motors dealer for a replacement.
If you wish to obtain an additional remote control trans-
mitter, please contact an authorized Mitsubishi Motors
dealer. A maximum of 4 remote control transmitters can
be programmed for your vehicle.NOTEYour keyless entry system operates on a radio frequency
subject to Federal Communications Commission (FCC)
Rules (For vehicles sold in U.S.A.) and Industry Canada
Rules (For vehicles sold in Canada). This device complies
with Part 15 of the FCC Rules and RSS-210 of the Indus-
try Canada Rules. Operation is subject to the following
two conditions:
• This device may not cause interference.
• This device must accept any interference received,
including interference that may cause undesired opera-
tion.
Procedure for replacing the remote control trans-
mitter battery1. With the Mitsubishi mark facing you, insert the cloth-cov-
ered tip of a flat blade screwdriver into the notch in the
remote control transmitter case and use it to open the case.NOTEBe sure to perform the procedure with the Mitsubishi
mark facing you. If the Mitsubishi mark is not facing you
when you open the remote control transmitter case, the
buttons may come out.
CAUTION
!Changes or modifications not expressly approved by
the manufacturer for compliance could void the
user’s authority to operate the equipment.
BK0121200US.book 10 ページ 2010年4月14日 水曜日 午前11時24分
Page 212 of 424
Features and controls
3-123
3 Digital clock
(if so equipped)
N00525100209
When the ignition switch is in the “ACC” or “ON” position,
the time is displayed.How each button works:Set the time by pressing the various buttons as described
below.
NOTEIf the battery cables are disconnected or the battery
becomes discharged, the clock will have to be reset.
H (HOUR)- Press and hold the “H” button until the correct
hour appears.
M (MINUTE)- Press and hold the “M” button until the correct
minute appears.
BK0121200US.book 123 ページ 2010年4月14日 水曜日 午前11時24分
Page 213 of 424
3-124 Features and controls
3HomeLink® Wireless Control System
(if so
equipped)N00554300027
HomeLink® Wireless Control System is a registered trademark
of Johnson Controls Inc..
HomeLink® provides a convenient way to consolidate the
functions of up to three individual hand-held transmitters into
one built-in device.
HomeLink® will operate most radio frequency devices such as
garage doors, gates, home and office lighting, entry door locks
and security systems.NOTEYour vehicle’s engine should be turned off while program-
ming HomeLink®.HomeLink® is powered by your vehicle’s battery. No sep-
arate batteries are required. If the vehicle’s battery is dis-
charged or is disconnected, HomeLink® will retain all
programming.
Once HomeLink® is programmed, retain the original
transmitter for future programming procedures (for exam-
ple, new vehicle purchases). Upon sale of the vehicle, the
programmed HomeLink® buttons should be erased for
security purposes.
WA R N I N G
!Do not use HomeLink® with any garage door
opener that lacks safety stop and reverse features as
required by U.S. Federal Regulations. A garage door
opener which cannot detect an object in the path of
a closing garage door and then automatically stop
and reverse, does not meet current U.S. Federal
Regulations. Using a garage door opener without
these features increases the risk of serious injury or
death.During programming, your garage door or gate may
open or close. Make sure that people and objects are
clear of the garage door or gate that you are pro-
gramming.
BK0121200US.book 124 ページ 2010年4月14日 水曜日 午前11時24分
Page 214 of 424
Features and controls
3-125
3
Programming HomeLink®To program HomeLink® to operate a garage door, gate, or
entry door opener, home or office lighting, you need to be at
the same location as the device. NOTESome garage door openers manufactured after 1996 have
“rolling code protection”. To program a garage door
opener equipped with “rolling code protection”; you will
need to access the garage door opener motor to press the
motor’s learn buttons. For convenience, use a ladder and
another person to assist you.
1. Unplug the device during the “cycling” process to prevent
possible damage to the garage door opener components.2. Press and hold the 2 outer HomeLink® buttons (A) (to
clear the memory) until the indicator light (B) blinks
slowly (after 20 seconds). Release both buttons.
3. Position the end of the hand-held transmitter 1 to 3 inches
(25 to 75 mm) away from HomeLink® surface.
4. Using both hands, simultaneously press and hold both
HomeLink® button (C) you want to program and the
hand-held transmitter button (D). Do not release the but-
tons until step 5 has been completed.
5. Hold down both buttons until the indicator light on
HomeLink® flashes, changing from a “slow blink” to a
“rapidly flashing blink”. This could take up to 90 seconds.
When the indicator light flashes rapidly, both buttons may
be released. The rapidly flashing light indicates successful
programming. Press and hold Homelink® button and
observe the indicator light.
BK0121200US.book 125 ページ 2010年4月14日 水曜日 午前11時24分
Page 215 of 424
3-126 Features and controls
3
6. If the indicator light on HomeLink® blinks rapidly for 2
seconds and then turns solid, HomeLink® has picked up a
“rolling code” garage door opener signal. Now continue
with the next steps to train HomeLink® to complete the
programming.
7. Press and release the “smart” or “learn” program button
located on the garage door opener’s motor to activate the
“training mode”. This button is usually located near the
antenna wire that hangs down from the motor. If the wire
originates from under a light lens, you will need to
remove the lens to access the program button.NOTEOnce you have pressed and released the program button
on the garage door opener’s motor and the “training light”
is on, you have 30 seconds in which to perform step 8.
Use the help of a second person for convenience to assist
when performing this step.
8. Quickly within 30 seconds of pressing and releasing the
garage door opener program button, firmly press and
release HomeLink® button you’ve just programmed.
Press and release HomeLink® button up to three times to
complete the training.
9. To program the remaining HomeLink® buttons for addi-
tional door or gate openers, follow steps 2-8 only.NOTEDo not repeat step 1 unless you want to “clear” all previ-
ously programmed HomeLink® buttons.
If you have any questions or are having difficulty programming
your HomeLink® buttons, please refer to the HomeLink® web
site at: www.homelink.com or call 1-800-355-3515.
Programming HomeLink® for Canadian cus-
tomersPrior to 1992, D.O.C regulations required hand-held transmit-
ters to stop transmitting after 2 seconds. To program your
hand-held transmitter to HomeLink®, continue to press and
hold HomeLink® button (note steps 2 through 4 under “Pro-
gramming HomeLink®”) while you press and re-press
(“cycle”) your hand-held transmitter every 2 seconds until the
indicator light flashes rapidly (indicating successful program-
ming).Operating HomeLink® To operate, simply press the appropriate programmed
HomeLink® button. The red indicator light will illuminate
while the signal is being transmitted. Programming trouble diagnosisIf HomeLink® does not quickly learn the hand-held transmitter
information:
Replace the hand-held transmitter batteries with new bat-
teries.
Position the hand-held transmitter with its battery area
facing away from HomeLink® surface.
Press and hold both HomeLink® and hand-held transmit-
ter buttons without interruption.
Position the hand-held transmitter 2 to 5 inches (50 to 126
mm) away from HomeLink® surface. Hold the transmit-
ter in that position for up to 15 seconds. If HomeLink® is
not programmed within that time, try holding the trans-
mitter in another position with the indicator light in view
at all times.
BK0121200US.book 126 ページ 2010年4月14日 水曜日 午前11時24分
Page 216 of 424
Features and controls
3-127
3
If you continue to have programming difficulties, please con-
tact an authorized Mitsubishi Motors dealer or a repair facility
of your choice. Clearing the programmed informationTo clear all programming, press and hold the two outside but-
tons and release when the indicator light begins to flash
(approximately 20 seconds) individual buttons cannot be
cleared.Reprogramming a single HomeLink® buttonTo reprogram a HomeLink® button, complete the following.
1. Press and hold the desired HomeLink® button. Do not
release the button until step 4 has been completed.
2. When the indicator light begins to flash slowly (after 20
seconds), position the hand-held transmitter 2 to 5 inches
(50 to 127 mm) away from HomeLink® surface.
3. Press and hold the hand-held transmitter button.
4. HomeLink® indicator light will flash, first slowly and
then rapidly. When the indicator light begins to flash rap-
idly, release both buttons.
The new device can be activated by pushing HomeLink® but-
ton that was just programmed. This procedure will not affect
any other programmed HomeLink® buttons.If your vehicle is stolenIf your vehicle is stolen, you should change the codes of any
non-rolling code device that has been programmed into
HomeLink®. Consult the Owner’s Manual of each device or
call the manufacturer or dealer of those devices for additional
information. When your vehicle is recovered, you will need to
reprogram HomeLink® with your new transmitter information.
General informationYour HomeLink® system operates on a radio frequency sub-
ject to Federal Communications Commission (FCC) Rules
(For vehicles sold in U.S.A.) and Industry Canada Rules (For
vehicles sold in Canada). This device complies with Part 15 of
the FCC Rules and RSS- 210 of the Industry Canada Rules.
Operation is subject to the following two conditions.
This device may not cause interference.
This device must accept any interference received, includ-
ing interference that may cause undesired operation.
CAUTION
!Changes or modifications not expressly approved by
the manufacturer for compliance could void the
user’s authority to operate the equipment.
BK0121200US.book 127 ページ 2010年4月14日 水曜日 午前11時24分
Page 265 of 424
5-28 Comfort controls
5
Radio control panel and display
N00734900843
1- PWR (On-Off) switch
2- Memory select buttons
3- RADIO (AM/FM selection) button
4- SEEK (Up-seek) button
5- SEEK (Down-seek) button
6- SCAN button
7- TUNE/FOLDER switch
8- SCAN indicator
9- AM/FM (AM/FM1/FM2) indicator
10- Preset memory number display
11- ST (Stereo) indicator
12- Frequency display
BK0121200US.book 28 ページ 2010年4月14日 水曜日 午前11時24分