battery MITSUBISHI iMiEV 2016 1.G Owner's Manual

Regular charging (charging method with rated AC 120 V outlet)
3
NOTE
 When the main drive lithium-ion battery warming system operates while the remoteclimate control is operating, the remote cli-mate control stops. When the main drive lith- ium-ion battery warming system stops, the remote climate cont
rol operates again.
BK0220401US.book 22 ページ ２０１５年６月３日　水曜日　午前７時４２分

EV charging cable 3-24 General information/Charging
3
: Illuminates : Blinking : Not illuminatedPOWER
FAULT
CHARGING
Operating condition
Every time the charging cable plug (C) is connected
to an outlet, all indicator lights illuminate
for 1/2 second, then go out. After initial processing is comple
ted, when the regular charge c
onnector is not connected to the
regular charge port, or the regular charge connec
tor is connected to the regular charge port but
charging is not being performed. While the main drive lithium-i
on battery is being charged
When the ground cable is disconnected Check the grounding of the outlet being used. If
the outlet is properly gr
ounded, contact a certi-
fied i-MiEV dealer. When charging is completed.
POWER
FAULT
CHARGING
Abnormal operating conditi
on and corrective action
When an electric leakage occurs or the EV charging cable malfunctions. Stop use immediately and contac
t a certified i-MiEV dealer.
When the EV chargi
ng cable malfunctions.
Stop use immediately and contac
t a certified i-MiEV dealer.
If the control box indicator light
does not illuminate after connect
ing the charging cable plug to
the outlet, check the circuit breaker for the outlet.
If the breaker has tripped, the circuit may not
be suitable for use with EV charging cable. Y
ou should have a licensed
electrician inspect and
repair the electrical circuit. If the breaker is
not tripped, stop using the EV charging cable and
contact a certifie
d i-MiEV dealer.
BK0220401US.book 24 ページ ２０１５年６月３日　水曜日　午前７時４２分

EV charging cable
General information/Charging 3-25
3
N01202901041
FCC Notice: This equi
pment has been tested
and found to comply with the limits for aClass B digital device,
pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable prot
ection against harmful
interference in a residential installation. This equipment generates, uses and can radi- ate radio frequency energy and, if notinstalled and used in accordance with the instructions, may caus
e harmful interference
to radio communications.However, there is no guarantee that interfer- ence will not occur in a particular installation. If this equipment does
cause harmful interfer-
ence to radio or tele
vision reception, which
can be determined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by
one or more of the
following measures:
WA R N I N G Improper use of the
EV charging cable
can result in a fire, property damage, andserious injury or death.Carefully read instructions regarding “Precautions during
charging the main
drive lithium-ion battery” on page 3-15and on “Regular charging (charging method with rated AC 120 V outlet)” on page 3-16 and describe
d in this section
and follow them. Always use an outlet protected by a ground-fault circuit interrupter, rated for 15A or more, and that
is connected to a
dedicated branch circuit. Never use an extension cable or conver- sion adapter. When using a non-wate
rproof outlet, take
care to avoid contact
with rainwater dur-
ing charging. Never connect or disconnect the plug with a wet hand. Make sure that the plug is inserted all the way into the socket before use. Continued charging with a plug not completely inserted or pulled
halfway out of the
socket may result in a risk of overheating or fire. If the indictors show the EV charging cable malfunctions as described below, stop using the EV charging cable and con-tact a certified i-MiEV dealer. Never disassemble the EV charging cable or attempt to open
the control box.
NOTE
All indicators are illuminated momentarily for confirming operation when the chargingcable plug is inserted into an outlet. Afterthat, the POWER indi
cator is continuously
illuminated and the CH
ARGING indicator is
continuously blinking.  The CHARGING indicator will start to blink when charging is completed. The POWERindicator is continuous
ly illuminated while
charging cable plug is in
serted into an outlet.
Handling and storing the con- trol box
CAUTION Use the method shown below to help secure the control box and to prevent the plug from being pulled halfway out of the socket duringcharging.NOTE
 Use hook (A) and a rope (B) that can support the weight of the EV charging cable, 8.8 lbs (4 kg) as shown in the figure below.
 Make sure that the rope has no damage before use.NOTE
A B
BK0220401US.book 25 ページ ２０１５年６月３日　水曜日　午前７時４２分

Regular charging (using 240 V Electric Vehicle Supply Equipment)
3
 Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.  Consult the dealer or an experienced radio/TV technician for help.
ICES Notice: This Class B digital apparatus complies with Canadian ICES-003.
N01203000013
1. Gently wipe outside surface of the EV charging cable with ga
uze or a similar soft
cloth soaked with a mild soap and watersolution. 2. Wipe off all detergent with a soft cloth dipped in fresh water and thoroughlywrung out. 3. Wipe all moisture off and dry in a shaded, well-ventilated area.
N01216101028
You can charge your vehicle through the reg-ular charge port using 240V Electric VehicleSupply Equipment (EVS
E) compatible with
i-MiEV. Carefully read instructions on “Precautionsduring charging the main drive lithium-ion battery” on page 3-15,
described in this sec-
tion.For connecting/disconne
cting the charging
connector to/from the vehicle, follow instruc-
tions for the regular charging (charging method with rated AC
120V outlet) on page
3-16. Also follow inst
ructions provided with
the 240V EVSE.
Cleaning the EV charging cable
WA R N I N G Before cleaning, be sure to remove the charging cable plug from the socket andthe regular charging plug from the vehi- cle. Do not connect or disconnect the plug with a wet hand. Doing so can cause anelectric shock.
 Never expose the metal terminal of the regular charge connector or the chargingcable plug to water or neutral detergent.Water or detergent entering into the plugs can cause a fire or
an electric shock.
CAUTIONNever use benzine, petrol, organic solvents, acid, or alkaline solvents to clean the charg- ing cable. Doing so c
ould cause deformation,
discolour, or malfunction. Also, these sub- stances may be present
in various cleaners,
so check carefully before use.
Regular charging (using 240 V Electric Vehicle Supply Equipment)
WA R N I N G
WA R N I N G Individuals using an
electro-medical
apparatus such as
implantable pacemak-
ers and implantable
cardiovascular-defi-
brillators should check with the manufacturer of the apparatus to confirm the effect of the electromagnetic wavesfrom charging. The el
ectromagnetic waves
may affect the operat
ions of the electro-
medical apparatus. If you use an electr
o-medical apparatus,
such as an implantable cardiac pacemakeror an implantable ca
rdiovascular defibril-
lator, observe the fo
llowing precautions
before charging;• Keep your electro-medical apparatusaway from the charge connector, EVcharging cable, control box and regular charging station.• While regular charging;· Do not stay inside the vehicle. · Do not go inside the
vehicle, for exam-
ple to remove or place an item in the passenger compartment.· Do not open the liftgate, for example to remove or place an item in the cargo area.
BK0220401US.book 26 ページ ２０１５年６月３日　水曜日　午前７時４２分

Quick charging (charging method with quick charger)
General information/Charging 3-27
3
N01203301039
Your vehicle is equipped with a quick charge port. The quick charge port is compatible with most CHAdeMO
* connectors on charg-
ing stations. * : CHAdeMO is a standard for quick charg- ing of electric vehicl
e originally started in
Japan, and the contents
have become an inter-
national standard. Char
ging stations using
this standard are UL certified and safe to usein the US. Improper charging can result in a fire, prop- erty damage, and serious injury or death.Carefully read and follow instructions on “Precautions during charging the main drive
lithium-ion battery”
on page 3-15, instruc-
tions described in th
is section and also
instructions for the quick charger you use.
CAUTION Be sure to use a 240V EVSE compatible with i-MiEV. Use of a non-compatible 240VEVSE may not charge the main drive lith-ium-ion battery correctl
y or may damage the
main drive lithium-ion battery.NOTE
 The 240V EVSE compatible with i-MiEV is available separately. Contact a certified i-MiEV dealer.
Quick charging (charging method with quick charger)
WA R N I N G Be sure to use a qu
ick charger compatible
with i-MiEV. Use of a non-compatiblequick charger may cause a fire or mal- function. For the quick charger compatible with i-MiEV, consult an certified i-MiEV dealer. For operation of a qu
ick charger, follow
instructions for each quick charger. If you use an electr
o-medical apparatus,
such as implantable cardiac pacemaker or an implantable cardi
ovascular defibrilla-
tor, follow the pr
ecautions described
below. Quick chargi
ng may affect the
operation of electric medical devices.• Do not perform quick charging and keepaway from a quick charger. Electromag- netic waves produced
by a quick charger
may affect the operat
ion of your electric-
medical apparatus. • If you have accide
ntally approached a
quick charger, walk
away from the quick
charger immediately.• If quick charging is
necessary, ask some-
one for help.• While quick charging;
· Do not stay inside the vehicle. · Do not go inside the vehicle, for exam- ple to remove or pl
ace an item in the
passenger compartment. · Do not open the liftgate, for example to remove or place an item in the cargoarea.
 Never connect or disc
onnect the charger
with a wet hand. Never pull the cable to disconnect the charger. During charging, the
cooling fans under
the hood may automa
tically be operated
even if the electric motor switch is in the “LOCK” position. Ke
ep your hands away
from the cooling fan during charging. As the quick charge connector is heavier in comparison to th
e regular charge con-
nector, allowing it to drop could cause damage to the vehicl
e or charge connector
or personal injury.CAUTION If the charge connector
cannot easily be con-
nected to the quick charge port, do not forcethe connection. Forei
gn material may be in
the charge connector or quick charge port, or the charging device may not be compatiblewith your vehicle. C
ontact a certified i-
MiEV dealer.WA R N I N G
BK0220401US.book 27 ページ ２０１５年６月３日　水曜日　午前７時４２分

Quick charging (charging method with quick charger) 3-28 General information/Charging
3
1. Fully apply the parking brake and move the selector lever to the “P” (PARK) posi- tion.2. Stop the electric devices such as lamps, air conditioning, etc.
and turn the electric
motor switch to the “LOCK” position.3. Pull the quick charging lid opener (A) at the bottom left of the driver’s seat to open the quick charging lid (B) at the left rearside of the vehicle.
4. Remove key and lock the vehicle. 5. Press the tab (C) to open the inner lid (D).
NOTE
 Repeatedly performi
ng only quick charging
can reduce the battery capacity. Regularcharging is recommended unless quickcharging is necessary.  Before using a publicly available quick char- ger, confirm that the charger is suitable for your vehicle.  Make sure to lock the doors to prevent theft, etc. during charging.  Do not turn the electric motor switch to the “ON” position during
quick charging; doing
so will stop quick charging.  When using a quick charger, make sure that the time available is
enough so that the quick
charging can be finished in the time avail- able. If the power supply of the quick charger isshut off during quick ch
arging, it could lead
to a vehicle failure.
A
B
E
D
C
WA R N I N G Do not touch the metal terminal of the quick charge port (E) and the quickcharge connector.Doing so could cause an electric shock and/or malfunction.CAUTION Be sure to insert the quick charge connector straight into the quick charge port all the wayto the base. Failure to do so may result in the main drive lithium-ion battery not charging or causedamage to the charging equipment. Do not leave the inner lid open for any sig- nificant period of ti
me without the charge
connector inserted.
Foreign material, if
allowed to enter the quick charge port, candamage the quick charge port and/or prevent charging.NOTE
 There is a hole on the quick charge port for water drainage. If this
hole is blocked and
water gets trapped in the quick charge port,do not charge. Contac
t a certified i-MiEV
dealer.
BK0220401US.book 28 ページ ２０１５年６月３日　水曜日　午前７時４２分

Quick charging (charging method with quick charger)
General information/Charging 3-29
3
6. Insert the quick charge connector com- pletely into the quick charge port to begin charging.For connecting and di
sconnecting, follow
the instruction manual for each quick charger. 7. Make sure that the charging indicator on the instrument cluster is illuminated.
If the charging indicator is not illumi- nated, charging has not started.Refer to the quick charger user manual.
8. Charging is complete when the charging indicator turns off. Disconnect the quick charge connectoraccording to the manual of the quick char- ger.
 If the quick charge port becomes frozen, use a hair dryer to defrost and dry it beforecharging. Forcing the charging connectorinto the quick charge port while it is frozen can damage the quick charge port, and it may prevent charging.WA R N I N G Be sure to insert the charge connector completely into the quick charge port.If the charge connector is only partially inserted and the connector latch is not locked, the electric motor switch could beturned to the “START” position and the vehicle could start moving NOTE
NOTE
 When the quick charging plug is connected to the charging connection, the charging indicator will blink.
Once charging has
started, the charging i
ndicator will illumi-
nate.
 The charge level for the main drive lithium- ion battery can be checked with the energylevel gauge (F) on the
instrument cluster.
Refer to “Energy leve
l gauge” on page 5-41.
 You may hear operating sounds from the main drive lithium-ion battery cooling sys-tem, such as sounds from the cooling fan and air conditioning comp
ressor, during quick
charging. This is normal.  Since the main driv
e lithium-ion battery
cooling system uses cool air from the airconditioning system,
the air conditioning
will automatically be operated. After quick charging, you may find dehu-midified water from
the air conditioning sys-
tem under the vehicle.
This is normal.
NOTE
F
BK0220401US.book 29 ページ ２０１５年６月３日　水曜日　午前７時４２分

Charging troubleshooting guide
General information/Charging 3-31
3
N01202301032
Charging troubleshooting guide
Symptom
Possible cause
Possible solution
Charging cannot be started. The elec
tric motor switch is in the
ON position.
Before charging, place the electric motor switch in the “LOCK” position.
The main drive lithium-ion battery is already fully charged.
Charging cannot be performed if the
main drive lithium-ion battery is
already fully charged. Charging automa
tically turns off if the main drive
lithium-ion battery is fully charged.
The temperature of the main drive lithium-ion battery is too high or too low to charge.
Confirm the main drive lithium-ion battery temperature. Refer to “Cautions and actions to deal
with intense heat” on page 3-8 and
“Cautions and actions to deal with intense cold” on page 3-10.
The 12V starter battery is discharged. The main drive lith
ium-ion battery can be charge
d if the vehicle electrical
systems cannot be turned on. If the batte
ry is discharged, charge or jump
start the 12V starter battery. Refer
to “Jump-starting” on page 8-2.
The vehicle or the charging cable has a malfunction.
The vehicle or the charging cable ma
y have a malfunction. Confirm if the
warning light on the meter is illuminated. Confirm if the indicator on the charger is indicating a malfunction. If
a warning is displayed, stop charg-
ing and contact a cer
tified i-MiEV dealer.
The fuse has blown. Confirm if the fuse of the in
terior lights (dome lights) in the fuse block in
the passenger compartment located in front of the driver’s seat has blown. Refer to “Fuses” on page 9-18.
BK0220401US.book 31 ページ ２０１５年６月３日　水曜日　午前７時４２分

Charging troubleshooting guide
General information/Charging 3-33
3
Regular charging is discon- tinued.
There is no power coming from the outlet.
There may have been a el
ectrical power failure,
or the breaker may have
failed.Charging will resume when
the power source is reset.
The EV charging cable has been dis- connected.
Check that the EV charging ca
ble has not been disconnected.
The button on the regular charge con- nector has been pressed.
If the charge connector button is pre
ssed for a long period of time, charg-
ing will be stopped. Start
the charging procedure again.
The temperature of the main drive lithium-ion battery is too hot or too cold to charge.
Confirm the main drive lithium-ion battery temperature. Refer to “Cautions and actions to deal
with intense heat” on page 3-8 and
“Cautions and actions to deal with intense cold” on page 3-10.
Charging is stopped by the regular charge timer.
Charging will stop depending on the
timer function setting of the regular
charge device. If you need to charge
the main drive lithium-ion battery
more, start the charging procedure again.
Quick charging cannot be started.
The charge connector is not con- nected correctly and/or not locked.
Check that the charge connector is
connected correctly and that it is
locked.
The self-diagnostic function of the quick charge device returns a nega- tive result.
There is a possibility that the vehicl
e has a malfunction. Stop charging and
contact a certified i-MiEV dealer.
The power switch of the quick char- ger is off.
Check the power switch of the quick charger. Consult an administrator or
a maker of the quick charger.
Quick charge is discontin- ued.
Charging is stopped by the quick charge timer.
Charging will stop depending on the
timer function setti
ng of the quick
charge device.If you need
to charge the main drive lithium-ion battery
more, start the charging procedure again.
Charging stops at 80% capacity. Cha
rging is designed to stop when th
e main drive lithium-ion battery
capacity reaches 80%. If you need to
charge the main drive lithium-ion
battery more than 80%, start
the charging procedure again.
The power supply for the quick char- ger is off.
Check whether the power supply for the quick charger is off. Consult an administrator or
a maker of the quick charger.
Symptom
Possible cause
Possible solution
BK0220401US.book 33 ページ ２０１５年６月３日　水曜日　午前７時４２分

High-Voltage components 3-34 General information/Charging
3
N01205700027
High voltage components and wiring cables are located as shown in the figure below.
The charging indicator is continuously blinking even if the quick charge connec- tor is not connected into the quick charge port when you start the electric motor unit after quick charging.
Quick charging has not finished nor- mally.
Perform quick charging ag
ain and finish it normally
or contact a certified
i-MiEV dealer.
EV (Electric Vehicle) sys- tem does not start after quick charging.
The vehicle has a malfunction. Cont
act a certified i-MiEV dealer.
If you need to push the vehicle, turn the electric motor switch to the “ON”
lector lever to the
“N”(NEUTRAL) position.
Symptom
Possible cause
Possible solution
High-Voltage components
WA R N I N GThe EV (Electric Vehicle) system uses high voltage up to DC 330 volt. The system can be hot during and after starting and when the vehicle is shut off. Be careful of boththe high voltage and
the high temperature.
Follow the warning labels that are attached to the vehicle.
 Never touch, disassemble, remove or replace high-voltage parts, exposed elec-trical components, cables or connectors. Failure to follow this instruction can result in severe burns or electric shockcausing serious injury
or death. High-volt-
age cables are colore
d orange. The vehicle
high voltage system has no user service-able parts. Take your
vehicle to a Certified
i-MiEV dealer for any necessary mainte- nance. Always assume the high voltage battery and associated components are energizedand fully charged.WA R N I N G
1- Regular charge port 2- MCU 3- Main drive lithium-ion battery 4- Heater5- Air conditioner compressor 6- High voltage connector 7- Service plug8- Electric motor (Electric motor unit) 9- On board charger/DC-DC converter
BK0220401US.book 34 ページ ２０１５年６月３日　水曜日　午前７時４２分