oil level MITSUBISHI L200 2017 Owner's Manual (in English)
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2017, Model line: L200, Model: MITSUBISHI L200 2017Pages: 426, PDF Size: 14.12 MB
Page 100 of 426
Indication and warning lamps (multi information display)E005015040931. Front fog lamp indication lamp*® p. 5-13
2. Turn-signal indication lamps/Hazard warning indication lamps ® p. 5-13
3. High-beam indication lamp ® p. 5-13
4. Auto Stop & Go (AS&G) indication lamp* ® p. 6-23
5. Lane departure warning (LDW) standby indication lamp (green)* ® p. 6-76
Lane departure warning (LDW) lamp
(amber)* ® p. 6-76
6. Position lamp indication lamp* ® p. 5-147. Lane departure warning (LDW) system
ON indication lamp* ® p. 6-76
8. Rear fog lamp indication lamp ® p. 5-13
9. Cruise control indication lamp* ® p. 6-63
10. Diesel particulate filter (DPF) warning lamp ® p. 6-21
11. Diesel preheat indication lamp ® p. 5-14
12. Charge warning lamp ® p. 5-16
13. Check engine warning lamp ® p. 5-15
14. Fuel filter indication lamp ® p. 5-1415. A/T (automatic transmission) fluid tem-
perature warning lamp (vehicles with
A/T) ® p. 6-34
16. Oil pressure warning lamp ® p. 5-16
17. Auto Stop & Go (AS&G) OFF indica- tion lamp* ® p. 6-26
18. Washer fluid level warning lamp* ® p. 5-16
19. Multi-information display ® p. 5-02
20- For details, refer to “Warning activa- tion” on page 3-12 (if so equipped).
21. For details, refer to “Warning activa- tion” on page 3-12 (if so equipped).
22- Door ajar warning lamp ® p. 5-16
Indication and warning lamps (multi information display)
5-12OKTE17E1Instruments and controls5Type 1
Type 2
Page 104 of 426
CAUTIONlIf the lamp illuminates while the engine is
running, avoid driving at high speeds and have the system inspected by a
MITSUBISHI MOTORS Authorized Serv-
ice Point as soon as possible.
Accelerator pedal and brake pedal response may be negatively influenced under these
conditions.NOTEl The engine electronic control module ac-
commodating the onboard diagnostic system has various fault data (especially about the
exhaust emission) stored.
This data will be erased if a battery cable is
disconnected which will make a rapid diag- nosis difficult. Do not disconnect a battery
cable when the check engine warning lamp is ON.
Charge warning lamp
E00502702304
This lamp illuminates when the ignition switch is turnedto the “ON” position or the
operation mode is put in ON, and goes off after the engine
has started.
CAUTIONl If it illuminates while the engine is running,
there is a problem in the charging system.
Immediately park your vehicle in a safe place and we recommend you to have it
checked.Oil pressure warning lamp
E00502801816
This lamp illuminates when
the ignition switch is turnedto the “ON” position or the
operation mode is put in ON, and the lamp goes off after
the engine has started. If it il-
luminates while the engine is running, the oil
pressure is too low.
If the warning lamp illuminates while the en- gine is running, turn the engine off and have
it inspected.
CAUTIONl If this lamp illuminates when the engine oil
level is not low, have it inspected.
l This warning lamp does not indicate the
amount of oil in the crankcase. This must be determined by checking the oil level on the
dipstick, while the engine is switched off.
l If you continue driving with low engine oil
level or with this warning lamp illuminated,
engine seizure may occur.NOTEl The oil pressure warning lamp should not be
treated as an indication of the engine’s oil
level. The oil level must be checked using
the dipstick.Door ajar warning lamp
E00503302020
This lamp illuminates when
a door is either open or not
completely closed.
If the vehicle speed reaches approximately 8 km/h
(5 mph) with a door open or
incompletely closed, a buzzer sounds 4 times as a warning.
CAUTIONl Before moving your vehicle, check that the
warning lamp is OFF.Washer fluid level warning
lamp*
E00569300042
This lamp comes on when
the washer fluid is running low.
If the lamp comes on, re-
plenish the container with washer fluid.
Refer to “Washer fluid” on page 10-08.
Warning lamps
5-16OKTE17E1Instruments and controls5
Page 143 of 426
Manual transmission*E00602002005
The shift pattern is shown on the gearshift lever knob. To start off, depress the clutch
pedal all the way down and shift into 1 st
or
“R” (Reverse) position. Then gradually re- lease the clutch pedal while depressing the
accelerator pedal.CAUTIONl Do not put the gearshift lever into the re-
verse position while the vehicle is moving forward. Doing so could damage the trans-mission.
l Do not rest your foot on the clutch pedal
while driving as this will cause premature clutch wear or damage.
l Do not coast in the “N” (Neutral) position.
l Do not use the gearshift lever as a hand rest,
because this can result in premature wear of the transmission shift forks.
l Quick or slight clutch engagement made
while the engine is running at high speed
will cause damage to the clutch and trans-
mission because the tractive force is very great.NOTEl During cold weather, shifting may be diffi-
cult until the transmission lubricant has
warmed up. This is normal and not harmful
to the transmission.
l If it is hard to shift into 1 st
, depress the
clutch pedal again; the shift will then be eas-
ier to make.
l In case of hot weather condition or long time
cruising with high speed, a speed limitation
function may work to restrict the oil temper-
ature rising of the manual transmission. Af- ter the oil temperature drops to the appropri-
ate level, the speed limitation function is cancelled.
l The gearshift indicator shows recommended
gearshift points for fuel-efficient driving. It
shows a
when an upshift is recommen-
ded.
Moving the gearshift lever to
the “R” (Reverse) position
E00615401211
Depress and hold the gearshift lever to the
“R” (Reverse) position.
CAUTIONl Do not depress the gearshift lever when
moving it to any position other than the “R”
(Reverse) position. If you always depress the gearshift lever when moving it, you could unintentionally move the gearshift lever tothe “R” (Reverse) position and cause an ac-
cident and/or a transmission fault.Possible driving speed
E00610802884
Avoid shifting down at high speed, as this
may cause excessive engine speed (the tach-
ometer needle into the red zone) and damage the engine.
Manual transmission*
6-27OKTE17E1Starting and driving6
Page 168 of 426
CAUTIONlAfter crossing a stream, apply the brakes to
be sure they are functioning properly. If the
brakes are wet and not functioning properly,
dry them out by driving slowly while lightly
depressing the brake pedal.
Inspect each part of the vehicle carefully.Inspection and maintenance
following rough roadoperation E00606701566
After operating the vehicle in rough road
conditions, be sure to perform the following inspection and maintenance procedures:
l Check that the vehicle has not been dam-
aged by rocks, gravel, etc.
l Carefully wash the vehicle with water.
Drive the vehicle slowly while lightly
depressing the brake pedal in order to dry out the brakes. If the brakes still do
not function properly, we recommend you to have the brakes checked as soon
as possible.
l Remove the insects, dried grass, etc.
clogging the radiator core and A/T oil
cooler.
l After crossing a stream, be sure to have
the following items inspected at aMITSUBISHI MOTORS Authorized
Service Point and take the necessary
measures. • Check the brake system and, if neces-
sary, have it serviced.
• Check the engine, transmission, trans-
fer, and differential oil or grease level
and turbidity. If the oil or grease is milky, it indicates water contamina-
tion. Replace it with new oil or grease.
• Grease the propeller shaft.
• Check the inside of the vehicle. If in-
gress of water is found, dry the carpet etc.
• Inspect the headlamps. If the head-
lamp bulb is flooded with water, have the headlamp drained off.Cautions on handling of 4-
wheel drive vehicles E00606802102
Tyres and wheels
Since the driving torque can be applied to the
4 wheels, the performance of the vehicle when operating in 4-wheel drive is greatly af- fected by the condition of the tyres.
Pay close attention to the tyres.
l Install specified tyres on all wheels. Re-
fer to “Tyres and wheels” on page
11-16.
l Be sure to the appropriate tyre inflation
pressure according to no cargo or cargo.
Refer to “Tyre inflation pressures” on
page 10-12.
l Be sure to fit all 4 tyres and wheels of
the same size and type.
When replacement of any of the tyres or wheels is necessary, replace all of them.
l All tyres should be rotated whenever the
wear difference between the front and
rear tyres is recognizable.
Good vehicle performance cannot be expec- ted if there is a difference in wear between tyres. Refer to “Tyre rotation” on page 10-13.
l Check the tyre inflation pressure regular-
ly.CAUTIONl Always use tyres of the same size, same
type, and same brand, and which have no wear differences. Using the tyres which dif-fer in size, type, brands or the degree of
wear or the inappropriate tyre inflation pres-
sure, will increase the differential oil tem- perature and may be impossible to shift the transfer, resulting in possible damage to thedriving system. Further, the drive train willbe subjected to excessive loading, possibly
leading to oil leakage, component seizure, or
other serious faults.
Inspection and maintenance following rough road operation
6-52OKTE17E1Starting and driving6
Page 323 of 426
4.Check the coolant level in the reserve
tank (B).
5. Add coolant to the radiator and/or re-
serve tank if necessary (refer to the
“Maintenance” section).
WARNINGl Make sure that the engine has cooled
down before removing the radiator cap (C), because hot steam or boiling water
otherwise will gush from the filler port and may scald you.CAUTIONl Do not add coolant while the engine is hot.
Suddenly adding cold coolant could damage the engine. Wait for the engine to cool
down, then add coolant a little at a time.6. Examine the radiator hoses for coolant
leakage and the drive belt for looseness
or damage.
If there is anything wrong with the cool-
ing system or drive belt, we recommend
you to have it checked and repaired.Bleeding the fuel system
E00800701423
The fuel system should be bled to remove air
as described below if the fuel supply is ex- hausted during travel.
Pump the hand pump (A) at the top of the fuel filter until the hand pump becomes stiff.Then try again to start the engine.
If the engine does not start, repeat the process
above.
CAUTIONl Do not smoke or have any other open flame
near the vehicle while bleeding the fuel sys-
tem.
l Be sure to carefully clean away any spilt fuel
which could ignite and cause a fire.Removal of water from the
fuel filter E00800801525
If the fuel filter indication lamp in the instru-ment panel illuminates during driving, it indi-
cates that water has accumulated in the fuel filter. If this occurs, remove the water as de-
scribed below. 1. Loosen the drain plug (A) of the fuel fil-
ter.
Bleeding the fuel system
8-11OKTE17E1For emergencies8FULLLOW
Page 351 of 426
1. Engine coolant reservoir
2. Brake fluid reservoir
3. Clutch fluid reservoir*
4. Engine oil cap
5. Engine oil level gauge
6. Power steering fluid reservoir
7. Washer fluid reservoir
8. BatteryCatalytic converter
E01000202596
The exhaust gas scavenging devices usedwith the catalytic converter are extremely ef- ficient for the reduction of noxious gases.
The catalytic converter is installed in the ex- haust system.
It is important to keep the engine properly
tuned to ensure proper catalyst operation and prevent possible catalyst damage.WARNINGl As with any vehicle, do not park or oper-
ate this vehicle in areas where combusti- ble materials such as dry grass or leaves
can come in contact with a hot exhaust
since a fire could occur.NOTEl Use fuel of the type recommended in
“Fuel
selection” on page 2-02.
Catalytic converter
10-03OKTE17E1Maintenance10RHD
LHD
Page 353 of 426
CAUTIONlBe careful that hands or fingers are not trap-
ped when closing the bonnet.
l Before driving, make sure that the bonnet is
securely locked. An incompletely locked bonnet can suddenly open while driving.
This can be extremely dangerous.NOTEl If this does not close the bonnet, release it
from a slightly higher position.
l Do not press down firmly on the bonnet as
doing so could damage it.Engine oil
E01000404693
To check and refill engine oil
A:Minimum level
B:Maximum level
C:Oil replacement indication mark
The engine oil used has a significant effect on the engine’s performance, service life and
startability. Be sure to use oil of the recom- mended quality and appropriate viscosity.
All engines consume a certain amount of oil during normal operation. Therefore, it is im-portant to check the oil level at regular inter-
vals or before starting a long trip. 1. Park the car on a horizontal surface.
2. Switch off the engine.
3. Wait a few minutes.
4. Remove the dipstick and wipe it with a
clean cloth.
5. Reinsert the dipstick as far as it goes.
6. Remove the dipstick and read the oil lev- el, which should always be within therange indicated.
7. If the oil level is below the specified
limit, remove the cap located on the cyl- inder head cover and add enough oil to
raise the level to within the specified
range. Do not overfill to avoid engine damage. Be sure to use the specified en-
gine oil and do not mix various types of
oil.
8. After adding oil, close the cap securely.
9. Confirm the oil level by repeating step 4
to 6.NOTEl Check or refill the oil according to the fol-
lowing manner.
• When the oil level is checked in step 6
above, check it on a low side of the dip-
stick because it is different in appearance
of oil level in the two sides of the dip-
stick.
• On vehicles without diesel particulate fil-
ter (DPF), the oil level should be within the range (A) to (B) on the dipstick.
• On vehicles with DPF, the oil level should
be within the range (A) to (C) (oil re-
placement indication mark) on the dip-
stick.
If the oil level is beyond the oil replace-
ment indication mark (C), replace the oil as soon as possible.
Then, the oil should be refilled to the maximum level (B).
Engine oil
10-05OKTE17E1Maintenance10
Page 354 of 426
NOTE•On vehicles with DPF, the engine oil will
increase due to a little fuel getting mixed
in the engine oil when the DPF regener- ates to burn away the PM (particulate
matter). However, it does not indicate a
malfunction.
• The engine oil level will be increased due
to an amount of the fuel being mixed in
the engine oil when the DPF regenerates
to burn away the PM (particulate matter). It does not indicate a malfunction.
In the following conditions, the engine oil level may increase easily. We recommendyou to have it checked frequently.
•frequent driving at uphill and down-
hill
• frequent driving at high altitudes
• frequent and extended idling
• frequent driving through a traffic
jam
l The engine oil will deteriorate rapidly if the
vehicle is subjected to severe conditions, re- quiring earlier oil replacement. Please refer
to the maintenance schedule.
l For handling of used engine oils, refer to
page 2-06.Selection of engine oil
l Select engine oil of the proper SAE vis-
cosity number according to the atmos-pheric temperature.
l Use engine oil conforming to the follow-
ing classification: • ACEA classification: “For service C1, C2, C3 or C4”
• JASO classification: “For service DL-1”
If those classifications are not available, con- tact a MITSUBISHI MOTORS Authorized
Service Point.
NOTEl Use of additives is not recommended since
they may reduce the effectiveness of addi-
tives already included in the engine oil. It may result in failure of the mechanical as-
sembly.Engine coolant
E01000503509
To check the coolant level
A transparent coolant reserve tank (A) is lo-cated in the engine compartment.
Engine coolant
10-06OKTE17E1Maintenance10
Page 403 of 426
Oil pressure warning lamp............................ 5-16
Overheating................................................... 8-09
Safety and disposal information for used engine oil............................................. 2-06
Specifications.............................................. 11-15
Entering or leaving the vehicle..........................2-04
ERA-GLONASS............................................... 8-02
Exterior and interior lamp operation............... 10-16
F
First-aid kit and warning triangleband for securing........................................... 7-109
Floor console box............................................ 7-106
Fluid Automatic transmission fluid...................... 11-18
Brake fluid........................................ 10-08,11-18
Clutch fluid....................................... 10-09,11-18
Engine coolant.................................. 10-06,11-18
Power steering fluid.......................... 10-09,11-18
Washer fluid..................................... 10-08,11-18
Front fog lamps
Bulb capacity.............................................. 10-22
Indication lamp............................................. 5-13
Replacement................................................ 10-27
Switch........................................................... 5-22
Front room lamp.............................................. 7-103
Bulb capacity.............................................. 10-23
Replacement................................................ 10-29
Front seats......................................................... 4-02
Front turn-signal lamps Bulb capacity.............................................. 10-22
Indication lamp............................................. 5-13
Replacement................................................ 10-25
Switch........................................................... 5-21
Frozen road warning..........................................5-06
Fuel consumption............................................ 11-17
Fuel remaining warning display........................ 5-07
Fuel Bleeding the fuel system............................... 8-11Filling the fuel tank....................................... 2-02Fuel filter indication lamp............................. 5-14
Fuel remaining display.................................. 5-07
Fuel remaining warning display....................5-07
Fuel selection................................................ 2-02
Modification/alterations to the electrical or fuel systems............................. 2-06
Removal of water from the fuel filter........... 8-11
Tank capacity................................................ 2-03
Fuses................................................................ 10-17
Fusible links.................................................... 10-17
G
General maintenance....................................... 10-16
General vehicle data........................................ 11-04
Genuine parts.....................................................2-06
Glove box........................................................ 7-105
Glove box lamp Bulb capacity.............................................. 10-23
Replacement................................................ 10-31
H
Hazard warning flasher switch.......................... 5-21
Hazard warning indication lamps......................5-13
HDMI terminal.................................................. 7-99
Head restraints................................................... 4-05
Headlamp levelling switch................................ 5-19
Headlamp washer switch...................................5-26
Headlamps Auto-cutout function..................................... 5-18Bulb capacity.............................................. 10-22
Daytime running lamps................................. 5-19 Dipper (High/Low beam change)................. 5-19
Headlamp flasher.......................................... 5-19
High-beam indication lamp...........................5-13
Lamp monitor buzzer.................................... 5-18
Replacement................................................ 10-24
Switch........................................................... 5-17
Heated mirror.................................................... 6-12
Switch........................................................... 5-27
Heated seats....................................................... 4-03
Heater........................................................ 7-04,7-09
High-mounted stop lamp Bulb capacity.............................................. 10-22
Hill start assist................................................... 6-55
Warning indicator......................................... 6-55
Hinges and latches lubrication........................ 10-16
Hooks Coat hook.................................................... 7-109Convenient hook......................................... 7-109
Horn switch....................................................... 5-28
I
If the vehicle breaks down................................ 8-07
Ignition switch................................................... 6-13
Indication and warning lamps........................... 5-12
Indication lamps........................................ 5-12,5-13
Inside rear-view mirror......................................6-08
Inspection and maintenance following rough road operation........................................ 6-52
Installation of accessories..................................2-04
Alphabetical index
12- 3
OKTE17E1Alphabetical index