roof MITSUBISHI L200 2017 Owner's Manual (in English)
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2017, Model line: L200, Model: MITSUBISHI L200 2017Pages: 426, PDF Size: 14.12 MB
Page 82 of 426
The front airbags and driver’s
knee airbag MAY NOT DE- PLOY when…
With certain types of frontal collisions, thevehicle’s body structure is designed to absorb
the shock to help protect the occupants from harm. (The vehicle body’s front area may de-form significantly as it absorbs the impact.) Under such circumstances, the front airbags and driver’s knee airbag may not deploy irre-
spective of the deformation and damage to the vehicle body.
Examples of some typical conditions are shown in the illustration.
1- Collision with a utility pole, tree or other
narrow object
2- Vehicle slides under the rear body of a
truck
3- Oblique frontal impacts
Because the front airbags and driver’s knee
airbag do not protect the occupant in all types
of frontal collisions, be sure to always prop- erly wear your seat belts.
The front airbags and driver’s knee airbag ARE NOT DE-SIGNED TO DEPLOY when…
The front airbags and driver’s knee airbag are
not designed to deploy in conditions where they cannot typically provide protection to
the occupant.
Such conditions are shown in the illustration.
1- Rear end collisions
2- Side collisions
3- Vehicle rolls onto its side or roof
Because the front airbags and driver’s knee
airbag do not protect the occupant in all types of collisions, be sure to always properly wearyour seat belts.
The front airbags and driver’s knee airbag MAY DEPLOY
when…
The front airbags and driver’s knee airbag
may deploy if the bottom of the vehicle suf- fers a moderate-to-severe impact (undercar- riage damage).
Examples of some typical conditions are shown in the illustration.
1- Collision with an elevated median/island
or kerb
2- Vehicle travels over a deep hole/pothole
3- Vehicle drives down a steep slope and
hits the ground
Supplemental restraint system (SRS)-airbag*
4-30OKTE17E1Seat and seat belts4
Page 84 of 426
The side airbag is designed to inflate only onthe side of the vehicle that is impacted, evenwith no passenger in the front seat.
The label shown here is attached to the seat- backs with a side airbag.
Curtain airbag system*
E00409101989
The curtain airbags are contained in the front
pillars and roof side rail. The curtain airbag is
designed to inflate only on the side of the ve- hicle that is impacted, even with no passen- ger in the front seat or rear seat.
Also, when the airbag control unit detects a
rollover of the vehicle, the curtain airbags
will deploy. (if so equipped)
Deployment of side airbags and
curtain airbags*
E00407702669
The side airbags and curtain
airbags ARE DESIGNED TO
DEPLOY when...
The side airbags and curtain airbags are de- signed to deploy when the vehicle suffers a
moderate-to-severe side impact to the middle of the passenger compartment.
The typical condition is shown in the illustra- tion.
1. Moderate to severe impact to the middle
of the vehicle body’s side structure
2. When the vehicle detects a rollover of
the vehicle (curtain airbag only)*
Supplemental restraint system (SRS)-airbag*
4-32OKTE17E1Seat and seat belts4
Page 85 of 426
The seat belts in your vehicle are your pri-mary means of protection in a collision. The SRS side airbags and curtain airbags are de-
signed to provide additional protection. Therefore, for your safety and the safety of all occupants, be sure to always properly
wear your seat belts.
The side airbags and curtain airbags MAY NOT DEPLOY
when...
With certain types of side collisions, the ve- hicle’s body structure is designed to absorbthe shock to help protect the occupants fromharm. (The vehicle body’s side area may de-form significantly as it absorbs the impact.) Under such circumstances, the side airbags
and curtain airbags may not deploy irrespec- tive of the deformation and damage to the ve-
hicle body. Examples of some typical condi- tions are shown in the illustration.
1. Side impacts in an area away from the
passenger compartment
2. Motorcycle or other similar small vehi-
cle collides with the side of vehicle
3. Collision with a utility pole, tree or other
narrow object
4. Oblique side impacts
5. Vehicle rolls onto its side or roof
Because the side airbags and curtain airbags do not protect the occupant in all types of side collisions, be sure to always properlywear your seat belts.
The side airbags and curtain
airbags ARE NOT DESIGNED TO DEPLOY when...
The side airbags and curtain airbags are notdesigned to deploy in conditions where they
cannot usually provide protection to the oc- cupant. Typical conditions are shown in the
illustration.
1. Head-on collisions
2. Rear end collisions
3. Pitch end over end*
Supplemental restraint system (SRS)-airbag*
4-33OKTE17E1Seat and seat belts4
Page 86 of 426
Because the side airbags and curtain airbags do not protect the occupant in all types of collisions, be sure to always properly wearyour seat belts.WARNINGl The side airbags and curtain airbags are
designed to supplement the driver and
passenger seat belts in certain side im- pacts. Seat belts should always be wornproperly, and the driver and passenger
should sit well back and upright without
leaning against the window or door.
l The side airbag and curtain airbag inflate
with great force. The driver and passen-
ger should not put their arms out of the window, and should not lean against the
door, in order to reduce the risk of serious or possible fatal injury from the deploying
side airbag and curtain airbag.WARNINGl Do not allow any rear seat occupant to
hold onto the seatback of either front seat,
in order to reduce risk of injury from the
deploying side airbag. Special care should
be taken with children.
l Do not place any objects near or in front
of the seatback of either front seat. They could interfere with proper side airbag in-
flation, and also could cause injury if thrown free by side airbag deployment.
l Do not place stickers, labels or additional
trim on the seatback of either front seat. They could interfere with proper side air-bag inflation.
l Do not install seat covers on seats with
side airbags.
Do not re-cover seats that have side air-
bags. This could interfere with proper side airbag inflation.
l Do not attach a microphone (A) or any
other device or object around the part
where the curtain airbags (B) activate
such as on the windscreen, side door glass, front and rear pillars and roof side or as- sist grips. When the curtain airbags in-
flate, the microphone or other device or object will be hurled with great force orthe curtain airbags may not activate cor-
rectly, resulting in death or serious injury.WARNINGl Do not put a hanger or any heavy or poin-
ted object on the coat hook. If the curtain
airbag was activated, any such item could
be propelled away with great force and could prevent the curtain airbag from in-
flating correctly. Hang clothes directly on the coat hook (without using a hanger).
Make sure there are no heavy or sharp objects in the pockets of clothes that you
hang on the coat hook.
l Do not allow a child to lean against or
close to the front door even if the child is
seated in a child restraint system.
The child’s head should also not lean against or be close to the area where the
side airbag and curtain airbag are loca-
ted. It is dangerous if the side airbag and curtain airbag inflate.
Failure to follow all of these instructions
could lead to serious or fatal injury to the
child.
Supplemental restraint system (SRS)-airbag*
4-34OKTE17E1Seat and seat belts4
Page 118 of 426
Economical drivingE00600102318
For economical driving, there are some tech- nical requirements that have to be met. Theprerequisite for low fuel consumption is a
properly adjusted engine. In order to achieve longer life of the vehicle and the most eco- nomical operation, we recommend you tohave the vehicle checked at regular intervals in accordance with the service standards.
Fuel economy and generation of exhaust gas
and noise are highly influenced by personal
driving habits as well as the particular operat- ing conditions. The following points shouldbe observed in order to minimize wear of
brakes, tyres and engine as well as to reduce
environmental pollution.
Starting the engine
Avoid sudden acceleration and sudden starts,
as they will increase fuel consumption.
Shifting
Shift only at an appropriate speed and engine speed. Always use the highest shift position
possible.
The transfer shift lever or the drive mode-se-
lector should be set to “2H” when driving 4WD vehicles on normal roads and express
ways to obtain best possible fuel economy.
City traffic
Frequent starting and stopping increases the
average fuel consumption. Use roads with smooth traffic flow whenever possible. When driving on congested roads, avoid use of a
low shift position at high engine speeds.
Idling
The vehicle consumes fuel even during idling. Avoid extended idling whenever pos-
sible.
Speed
At higher vehicle speed, more fuel is con-
sumed. Avoid driving at full speed. Even a slight release of the accelerator pedal willsave a significant amount of fuel.
Tyre inflation pressure
Check the tyre inflation pressures at regularintervals. Low tyre inflation pressure increa-ses road resistance and fuel consumption. In
addition, low tyre pressures adversely affect tyre wear and driving stability.
Cargo loads
Do not drive with unnecessary articles in the
luggage compartment. Especially during city
driving where frequent starting and stopping is necessary, the increased weight of the ve-
hicle will greatly affect fuel consumption. Al- so avoid driving with unnecessary luggage or carriers, etc., on the roof; the increased air re- sistance will increase fuel consumption.
Cold engine starting
Starting of a cold engine consumes more fuel. Unnecessary fuel consumption is alsocaused by keeping a hot engine running. Af-
ter the engine is started, commence driving as soon as possible.
Cooler or air conditioning
The use of the air conditioner will increase the fuel consumption.
Driving, alcohol and drugs
E00600200070
Driving after drinking alcohol is one of the
most frequent causes of accidents.
Economical driving
6-02OKTE17E1Starting and driving6
Page 167 of 426
WARNINGlGo straight up. Do not try to traverse
across a steep slope.
l If you begin to lose traction, ease off the
accelerator pedal and gently turn the
steering wheel alternatively left and right to regain adequate traction again.NOTEl Choose as smooth a slope as possible with
few stones or other obstacles.
l Before attempting to drive up the slope,
walk up it to confirm that the vehicle canhandle the grade.
Descending sharp grades
Set the drive mode-selector to “4L” position
(Easy select 4WD), “4LLc” position (Super
select 4WD II), use the engine brake (down- shifting) and descend slowly.
WARNINGl Avoid snaking down a sharp grade. De-
scend the grade as straight as possible.NOTEl When descending a sharp grade, if the
brakes are applied suddenly because of an
obstacle encountered, control of the vehicle
could be lost. Before descending the slope,
walk down it and confirm the path.
l Before descending a grade, it is necessary to
choose the appropriate gear. Avoid changing
gears or depressing the clutch while de- scending the grade.
l MITSUBISHI
MOTORS is not responsible
to the operator for any damage or injury caused or liability incurred by improper and
negligent operation of a vehicle. All techni- ques of vehicle operation described herein depend on the skill and experience of the op-
erator and other participating parties and any
deviation from the recommended operation instructions above is at their own risk.
Turning sharp corners
When turning a sharp corner in “4H” or “4L”
position (Easy select 4WD), “4HLc” or “4LLc” position (Super select 4WD II) at low
speed, a slight difference in steering may be experienced similar to as if the brakes wereapplied. This is called tight corner braking
and results from each of the 4 tyres being at a different distance from the corner.
Crossing a stream
4-wheel drive vehicles are not necessarily
waterproof. If the electrical circuits become
wet, further operation of the vehicle will be impossible; therefore, avoid crossing streams
unless absolutely necessary. If crossing a
stream is unavoidable, use the following pro- cedure: 1. Check depths of a stream and geographi-
cal features before attempting to cross a
stream and ford the stream where the water is as shallow as practicable.
2. Set the drive mode-selector to “4L” po-
sition (Easy select 4WD), “4LLc” posi-
tion (Super select 4WD II).
3. Drive slowly at a speed of approximate-
ly 5 km/h (3 mph) to avoid splashing too
much water.
CAUTIONl Never cross a stream where the water is
deep.
Do not change gears while crossing the stream.
Frequent crossing of streams can adversely affect the life span of the vehicle; we recom-mend you to take the necessary measures toprepare, inspect, and repair the vehicle.
4-wheel drive operation*
6-51OKTE17E1Starting and driving6
Page 277 of 426
AntennaE00710500022Pillar antenna*
E00710701151
When listening to the radio, fully extend theantenna.
NOTEl Be sure to retract the pillar antenna in the
following cases:
• When entering a place with low clear-
ance.
• When using an automatic car wash.
• When placing a car cover over the vehi-
cle.Roof antenna*
E00710901209
When listening to the radio, raise the antenna
up until you hear it click.
To remove
Turn the pole (A) anticlockwise.
To install
Screw the pole (A) clockwise into the base (B) until it is securely retained.
NOTEl Be sure to remove the roof antenna in the
following cases:
• When using an automatic car wash.
• When placing a car cover over the vehi-
cle.
• When driving into a structure that has a
low ceiling.
Antenna
7-75OKTE17E1For pleasant driving7 Type 1 Type 2 Type 1 Type 2
Page 346 of 426
CAUTION•Maintain a distance of approx. 70 cm
or
more between the vehicle body and the washing nozzle.
• When washing around the door glass,
hold the nozzle at a distance of more than
70 cm and at right angles to the glass sur- face.
l After washing the vehicle, drive the vehicle
slowly while lightly depressing the brake
pedal several times in order to dry out the
brakes.
Leaving the brakes wet could result in re- duced braking performance. Also, there is a
possibility that they could freeze up or be- come inoperative due to rust, rendering the vehicle unable to move.
l When using an automatic car wash, pay at-
tention to the following items, referring to the operation manual or consulting a car
wash operator. If the following procedure is not followed, it could result in damage to
your vehicle.
• The outside mirrors are retracted.
• If your vehicle is equipped with the pillar
antenna, it can be retracted.
• If your vehicle is equipped with the roof
antenna, it can be removed.
• The wiper arms are secured in place with
tape.
• If your vehicle has rain sensor wipers,
place the wiper switch lever in the “OFF” position to deactivate the rain sensor.During cold weather
Salt and other chemicals spread on the roads
in some areas in winter can have a harmful effect on the vehicle body. You should there-
fore wash the vehicle as often as possible in accordance with our care-instructions. It is
recommended to have a preservative applied
and the underfloor protection checked before and after the cold weather season.
After washing your vehicle, wipe off all wa- terdrops from the rubber parts around the
doors to prevent the doors from freezing.
Waxing
E00901001974
Waxing the vehicle will help prevent the ad-
herence of dust and road chemicals to the paintwork. Apply a wax solution after wash- ing the vehicle, or at least once every three
months to assist displacing of water.
Do not wax your vehicle in direct sunlight.
You should wax after the surfaces have
cooled.
For information on how to use wax refer to the instruction manual of the wax.
CAUTIONl Waxes containing high abrasive compounds
should not be used.Polishing
E00901101151
The vehicle should only be polished if the
paintwork has become stained or lost its lus- tre. Do not polish parts with a mat coating
and the plastic bumpers. Doing so could cause stains or damage the finish.
Cleaning plastic parts
E00901301876
Use a sponge or chamois leather.
If a car wax adheres on a grey or black rough surface of the bumper, moulding or lamps, the surface becomes white. In such a case,
wipe it off using lukewarm water and soft cloth or chamois leather.
CAUTIONl Do not use a scrubbing brush or other hard
tools as they may damage the plastic part surface.
l Do not bring the plastic parts into contact
with petrol, light oil, brake fluids, engine oils, greases, paint thinners and sulphuric
acid (battery electrolyte) which may crack, stain or discolour the plastic parts.
If they touch the plastic parts, wipe them off with soft cloth, chamois or the like and anaqueous solution of neutral detergent then
immediately rinse the affected parts with
water.
Cleaning the exterior of your vehicle
9-04OKTE17E1Vehicle care9
Page 366 of 426
3-Remove the glove box fastener (B), and
then remove the glove box.
Engine compartment
In the engine compartment, the fuse block is located as shown in the illustration.
1- Push the tab.
2- Remove the cover.
Fuse load capacity
E01007701838
The fuse capacity and the names of electrical
systems protected by the fuses are indicated
on the inside of the fuse lid (LHD vehicles), the back side of the glove box (RHD vehi-cles) and inside of the fuse block cover (in-
side of the engine compartment).
NOTEl Spare fuses are provided in the fuse block of
the engine compartment. Always use a fuse
of the same capacity for replacement.Passenger compartment fuse lo-
cation table
E01007901944
No.Sym- bolElectrical sys- temCa-
pacity1Tail lamp (left)7.5 A2Cigarette lighter15 A3Ignition coil10 A4Starter motor7.5 A5Sunroof20 A6Accessory sock- et15 A7Tail lamp (right)7.5 A8Outside rear-view mirrors7.5 A9Engine control unit7.5 A10Control unit7.5 A11Rear fog lamp10 A12Central doorlock15 A13Room lamp15 A14Rear windowwiper15 A15Gauge10 A*: Fusible link
Fuses
10-18OKTE17E1Maintenance10
Page 401 of 426
4
4-wheel drive operation.....................................6-49A
Accessory (Installation).....................................2-04
Accessory socket............................................. 7-102
Active Stability & Traction Control (ASTC).... 6-59 ASC OFF switch........................................... 6-60
ASTC indication lamp.................................. 6-62
ASTC OFF indication lamp.......................... 6-62
Air conditioner
Automatic climate control air conditioner.... 7-09
Manual air conditioning................................ 7-04
Refrigerant (Air conditioning).................... 11-18
Air conditioning
Important operation tips for the airconditioning................................................. 7-17
Air purifier.........................................................7-17
Airbag................................................................ 4-24 Curtain airbag system................................... 4-32
Driver’s and front passenger’s air- bag system................................................... 4-28
Driver’s knee airbag system..........................4-29
Front passenger’s airbag indicator................ 4-27
Front passenger’s airbag ON-OFF switch.... 4-27
How the Supplemental Restraint System works...............................................4-25
Side airbag system........................................ 4-31
SRS servicing................................................ 4-35
SRS warning lamp........................................ 4-35
AM/FM radio.................................................... 7-18
Antenna............................................................. 7-75 Pillar antenna................................................ 7-75
Roof antenna................................................. 7-75
Anti-lock brake system (ABS).......................... 6-57
Warning lamp................................................6-57
Armrest (Double cab)........................................ 4-04
Ashtray............................................................ 7-101
Assist grip........................................................7-109
Audio AM/FM radio................................................ 7-18
Audio Files........................................... 7-20,7-43
Audio Quality and Volume Bal- ance Adjustment.................................. 7-36,7-67
Bluetooth® 2.0 interface............................... 7-76
CD player.............................................. 7-18,7-39
Display Indicator.................................. 7-35,7-66
Handling of Discs................................. 7-19,7-42
Important Points on Safety for the Customer............................................. 7-24,7-47
Link System.................................................. 7-76
Listen to an iPod................................... 7-31,7-57
Listen to Audio Files on a USB Device..................................................7-33,7-58
Listen to Bluetooth Audio............................. 7-64
Listen to CDs........................................ 7-29,7-55
Listen to DAB............................................... 7-53
Listen to MP3s.............................................. 7-55
Listen to MP3s/WMAs/AACs...................... 7-30
Listen to Radio......................................7-28,7-52
Listen to Traffic Messages............................ 7-54
LW/MW/FM radio........................................ 7-39
Operation Keys..................................... 7-25,7-48
Steering control switch and microphone.......7-77 Steering wheel audio remote con- trol switches.........................................7-28,7-51
System Settings............................................. 7-36 Time Setting......................................... 7-37,7-70
To play iPod/USB memory device tracks via voice operation............................ 7-61
Troubleshooting.................................... 7-38,7-72USB input terminal....................................... 7-96
Use AUX....................................................... 7-35
Auto Stop & Go (AS&G) system......................6-23
Auto Stop & Go (AS&G) OFF switch..........6-26
Auto Stop & Go indication lamp.................. 6-23
Auto Stop & Go OFF indication lamp.......... 6-26
Automatic transmission
AUX.............................................................. 7-35
Fluid............................................................ 11-18
Paddle shift....................................................6-31
Selector lever operation................................ 6-28
Selector lever position...................................6-31
Selector lever position display...................... 6-31
Sports mode.................................................. 6-31
Sports mode indicator................................... 6-33
Warning lamp................................................6-34
B
Battery............................................................. 10-10Charge warning lamp.................................... 5-16
Discharged battery (Emergency starting)..... 8-08
Specification............................................... 11-16
Bleeding the fuel system................................... 8-11
Bluetooth® 2.0 interface................................... 7-76
Bonnet............................................................. 10-04
Bottle holder.................................................... 7-108
Brake ABS warning lamp........................................ 6-57
Anti-lock brake............................................. 6-57
Brake assist system....................................... 6-56
Brake system................................................. 6-54
Brake warning lamp...................................... 5-15
Braking.......................................................... 6-53
Fluid.................................................. 10-08,11-18
Parking brake................................................ 6-05
Alphabetical index
12- 1
OKTE17E1Alphabetical index