window MITSUBISHI L200 2017 Owner's Manual (in English)

Instruments and Controls (Driver’s area)E085001018111. Shift paddles* p. 6-312. Instruments p. 5-02
3. Headlamp washer switch* p. 5-26 Wiper and washer switch p. 5-23
4. Active stability control (ASC) OFF switch p. 6-60
5. Fuel tank filler door release lever* p. 2-02
6. Bonnet release lever p. 10-04
7. Electric window control switch* p. 3-22
8. Lock switch* p. 3-22
9. Headlamp leveling switch p. 5-19
10. Lane departure warning (LDW) switch* p. 6-76
11. Outside rear-view mirrors switch* p. 6-09
12. Ignition switch* p. 6-13 Engine switch* p. 6-14
13. Combination headlamps and dipper switch p. 5-17 Turn-signals lever p. 5-20
Front fog lamp switch* p. 5-22
Rear fog lamp switch p. 5-22
Instruments and Controls (Driver’s area)
1-02OKTE17E1Overview/Quick guide1

Instruments and ControlsE085001018241. Audio* p. 7-39Digital clock* p. 7-102
DISPLAY AUDIO*, MITSUBISHI Multi-Communication Sys-
tem*, Smartphone Link Display Audio*
Refer to the separate owner’s manual
2. Centre ventilators p. 7-02
3. Heater*/Air conditioning* p. 7-04
4. Front passenger’s airbag indicator p. 4-25, 4-27
5. Supplemental restraint system (SRS) - airbag (for front passen- ger’s seat) p. 4-25, 4-28
6. Side ventilators p. 7-02
7. Glove box p. 7-105
8. Cigarette lighter p. 7-101
9. USB input terminal* p. 7-96 HDMI terminal* p. 7-99
10. Key slot* p. 6-20
11. Centre console under tray p. 7-105, 7-106
12. Gearshift lever* p. 6-27 Selector lever* p. 6-28
13. Parking brake lever p. 6-05
14. Cup holder p. 7-107
15. Floor console box p. 7-105, 7-106 Accessory socket p. 7-102
16. Easy select 4WD* p. 6-35 Super Select 4WD II* p. 6-40
17. Auto Stop & Go (AS&G) OFF switch* p. 6-23
18. Rear differential lock switch* p. 6-45
19. Heated seat switch* p. 4-03
20. Hazard warning flasher switch p. 5-21
21. Supplemental restraint system (SRS) - airbag (for driver’s seat) p. 4-24, 4-28
Horn switch p. 5-28
22. Bluetooth ®
2.0 interface* p. 7-76
23. Audio remote control switches* p. 7-28
24. Cruise control switch* p. 6-64
25. Rear window demister switch p. 5-27
Instruments and Controls
1-03OKTE17E1Overview/Quick guide1

1. Front passenger’s airbag indicator* p. 4-25, 4-27
2. Steering wheel height and reach adjustment lever p. 6-07
3. Audio remote control switches* p. 7-28, 7-51
4. Cruise control switch* p. 6-64
5. Supplemental restraint system (SRS) - airbag (for driver’s seat) p. 4-24, 4-28
Horn switch p. 5-28
6. Bluetooth ®
2.0 interface* p. 7-76
7. Hazard warning flasher switch p. 5-21
8. Cigarette lighter p. 7-101
9. USB input terminal* p. 7-96 HDMI terminal* p. 7-99
10. Auto Stop & Go (AS&G) OFF switch* p. 6-23
11. Parking brake lever p. 6-05
12. Floor console box p. 7-105, 7-106 Accessory socket p. 7-102
13. Cup holder p. 7-107
14. Easy select 4WD* p. 6-35 Super Select 4WD II* p. 6-40
15. Gearshift lever* p. 6-27 Selector lever* p. 6-28
16. Centre console under tray p. 7-105, 7-106
17. Key slot* p. 6-20
18. Rear differential lock switch* p. 6-45
19. Heated seat switch* p. 4-03
20. Fuses p. 10-17
21. Glove box p. 7-105
22. Side ventilators p. 7-02
23. Supplemental restraint system (SRS) - airbag (for front passen- ger’s seat) p. 4-25, 4-28
24. Heater*/Air conditioning* p. 7-04
25. Centre ventilators p. 7-02
26. Rear window demister switch p. 5-27
Instruments and Controls
1-04OKTE17E1Overview/Quick guide1

Refer to “Steering wheel height and reach
adjustment” on page 6-07.
5-Wiper and washer switch Except for vehicles equipped with rain
sensor MIST- Misting function
The wipers will operate
once.
OFF- Off INT- Intermittent (Speed sensi- tive)
LO- Slow HI- Fast Vehicles with rain sensor
MIST- Misting function
The
wipers will operate
once.
OFF- Off
AUTO- Auto-wiper control Rain sensor
The

wipers will automati-
cally operate depending on
the degree of wetness on
the windscreen.
LO- Slow HI- Fast
The
washer fluid will be sprayed onto the
windscreen by pulling the lever towards you.
Refer to “Wiper and washer switch” on page 5-23. 6-Electric window control* Press the switch down for opening the win-
dow, and pull the switch for closing. 1. Driver’s door window
2.

Front passenger’s door window
3. Rear left door window (Double cab)
4. Rear right door window (Double cab)
5. Lock switch
Lock switch
If you press the switch (5), the passenger’s switches cannot be operated. To cancel, press
it once again.
Refer to “Electric window control*” on
page 3-21.
Quick guide
1-18
OKTE17E1
Overview/Quick guide 1 Driver’s switch
L
HD Driver’s switch
RHD

WARNINGlKeep the doors and windows closed while
refueling the vehicle. If they were open,fuel vapour could get into the cabin.
l If the fuel cap must be replaced, use only
a MITSUBISHI MOTORS genuine part.
Fuel tank capacity
75 litres
Refueling
1. Before filling with fuel, stop the engine.
2. The fuel tank filler is located on the rear
left side of your vehicle.
Open the fuel tank filler door with the
release lever located below the instru- ment panel. (Only vehicles for Type 1,
2)
3. [Vehicles for Type 1, 2] Open the fuel tank filler tube by slowly
turning the fuel cap anticlockwise.1- Remove
2- Close

[Vehicles for Type 3]
Open the cover (1). Insert the key in the
fuel cap (2) and unlock it.
Turn the fuel cap and remove it.
Filling the fuel tank
2-03OKTE17E1General information2 Type 1 Type 2 Type 1 Type 2 Type 3

Keys.................................................................................................... 3-02Key number tag................................................................................... 3-02
Electronic immobilizer (Anti-theft starting system)........................... 3-03
Keyless entry system*.........................................................................3-03
Keyless operation system*.................................................................. 3-07
Doors................................................................................................... 3-15
Central door locks............................................................................... 3-17
Dead Lock System*............................................................................ 3-18
“Child-protection” rear doors (Double cab)........................................3-20
Rear gate............................................................................................. 3-20
Manual window control*.................................................................... 3-21
Electric window control*.................................................................... 3-21Locking and unlocking
OKTE17E13

NOTElIf the keyless operation key battery is wear-
ing out or there are strong electromagnetic
waves or noise present, the operating range
may become smaller and operation may be-
come unstable.Operating range for locking
and unlocking the doors
E00306201568
The operating range is approximately 70 cm from the driver’s or front passenger’s door
lock/unlock switch.
*: Forward direction: Operating rangeNOTEl Locking and unlocking operates only when
you press a door switch that detects the key-
less operation key.
l Operation may not be possible if you are too
close to the front door, door window.
l Even if the keyless operation key is within
70 cm of the driver’s or front passenger’s
door lock/unlock switch, if the key is near to the ground or high up, the system may not operate.
l If the keyless operation key is within the op-
erating range, even someone not carrying the key can lock and unlock the doors by press-ing the driver’s or front passenger’s door
lock/unlock switch.Operating range for starting the
engine and changing the opera-tion mode
E00306301338
The operating range is the interior of the ve-
hicle.
*:Forward direction:Operating rangeNOTEl Even if it is within the operating range, if the
keyless operation key is in a small item
holder such as the glove box, on top of the instrument panel, door pocket or in the lug-gage compartment, it may be impossible to
start the engine and change the operation
mode.
Keyless operation system*
3-09OKTE17E1Locking and unlocking3

NOTElIf a keyless operation key is too close to the
door or door window, it may be possible to start the engine or change the operation
mode even when the key is outside the vehi- cle.To operate using the keyless
operation function
E00305802173
Locking the doors
When you are carrying the keyless operation
key, if you press the driver’s or front passen- ger’s door lock/unlock switch (A), within theoperating range, the doors are locked.
The turn-signal lamps will blink once.
Also refer to “Locking and unlocking: Doors,
Central door locks” on pages 3-15, and
3-17.
Unlocking the doors
When you are carrying the keyless operation
key, if you press the driver’s or front passen- ger’s door lock/unlock switch (A), within theoperating range, all the doors are unlocked.
If the room lamp switch is in the middle (•)
position at this time, the room lamp will turn
on for 15 seconds. The turn-signal lamps will blink twice.
If the driver’s or front passenger’s door lock/
unlock switch is pressed and any of the doors
is not opened within approximately 30 sec-
onds, relocking will automatically occur. Refer to “Locking and unlocking: Doors, Central door locks” on pages 3-15, and
3-17.
NOTEl For vehicles equipped with the mirror retrac-
tor switch, the outside rear-view mirrors au-
tomatically retract/extend when all the doors are locked/unlocked using the keyless opera-tion function. Refer to “Starting and driving:
Outside rear-view mirrors” on page 6-09.
l For vehicles equipped with the Dead Lock
System, pressing the driver’s or front pas-
senger’s door lock/unlock switch (A) two times in succession causes the Dead Lock
System to be set. (Refer to “Setting the sys-
tem” on page 3-19.)
l The keyless operation function does not op-
erate under the following conditions:NOTE• The keyless operation key is inside the
vehicle.
• A door is open or ajar.
• The operation mode is not in OFF.
l The time between unlocking and automatic
locking can be adjusted. Please consult a
MITSUBISHI MOTORS Authorized Serv-
ice Point.
Operation confirmation when locking and
unlocking
Operation can be confirmed as shown below. However, the room lamp will illuminate only if the room lamp switch is in the middle (•)position.
When locking:The turn-signal
lamps will blink
once.When unlocking:The room lamp illu-
minates for approxi-
mately 15 seconds,
the turn-signal lamps
blink twice.NOTEl Functions can be modified as stated below.
For further information, please contact a
Keyless operation system*
3-10OKTE17E1Locking and unlocking3

Warning activation
E00305902031
In order to prevent vehicle theft or the accidental operation of the keyless operation system, the lamp and buzzer are used to alert the driver.
LampBuzzerItemCauseNote (Solution)Blinks.Outer buzzer sounds
4 times. Inner buzzer
sounds.Keyless operation key
take-out monitoring systemWhen the vehicle is parked with the opera- tion mode in any mode other than OFF, if you close the door after opening any of the
doors and taking the keyless operation key out of the vehicle.
Outer buzzer sounds 4 times at this time.
And when a vehicle starts, inner buzzer
sounds once.l If you take the keyless opera-
tion key out of the vehiclethrough a window without
opening a door, this system does not operate.
l It is possible to change the set-
ting to make the system operate
if you take the keyless opera-
tion key out from the vehicle through a window without
opening a door. For further in- formation, please contact a MITSUBISHI MOTORS Au-
thorized Service Point.
l Even if you have the keyless
operation key within the engine start operating range, if the keyand vehicle ID codes cannot be
matched, for example due to the ambient environment or electromagnetic conditions, the
warning may be activated.
Keyless operation system*
3-12OKTE17E1Locking and unlocking3

Setting the system
E00305201314
1. Turn the ignition switch to the “LOCK”
position and then remove the key (vehi-
cles with keyless entry system), or put the operation mode in OFF (vehicles
with keyless operation system).
2. Get out of the vehicle. Close all of the
doors.
3. Press the LOCK switch (A) on the key,
the driver’s or front passenger’s door
lock/unlock switch (C) to lock all of the doors. The turn-signal lamps will blink
once.
4. Press the switch again within 2 seconds.
The turn-signal lamps will blink three times to show that the Dead Lock Sys- tem has been set.
NOTEl Pressing the LOCK switch (A) on the key
once while the Dead Lock System is set cau-ses the turn-signal lamps to blink three
times, so it is possible to confirm that the Dead Lock System is set.Cancelling the system
E00305301331
When the following operation is performed,
the doors will unlock and the Dead Lock Sys- tem will be simultaneously cancelled.
l The UNLOCK switch (B) on the key is
pressed.
l The driver’s or front passenger’s door
lock/unlock switch (C) is pressed while you are carrying the keyless operation
key.
NOTEl If a door is opened within 30 seconds of un-
locking, the doors are automatically relocked
and the Dead Lock System is simultaneously
set again.
l Even when it is not possible to use the key-
less entry system or keyless operation func-
tion to unlock the doors, it is possible to use the key to unlock the driver’s door. When
the key is used to unlock the driver’s door,
the Dead Lock System is cancelled for only the driver’s door. If you wish to subsequent- ly unlock all other doors, turn the ignition
switch to the “ON” or “ACC” position, or put the operation mode in on or ACC.
l It is possible to adjust the time between
pressing the UNLOCK switch (B) on the key or the driver’s or front passenger’s door
lock/unlock switch (C) and automatic lock- ing. For details, please contact aMITSUBISHI MOTORS Authorized Serv-
ice Point.
l It is possible to lock the doors and set the
Dead Lock System at the same time with a
single push of the LOCK switch (A) on the key, the driver’s or front passenger’s door
lock/unlock switch (C). For details, please
contact a MITSUBISHI MOTORS Author-
ized Service Point.Testing the system
E00305400159
Open all of the door windows, then set the
Dead Lock System.
(Refer to “Setting the system” on page 3-19.)
Dead Lock System*
3-19OKTE17E1Locking and unlocking3Keyless entry system Keyless operation system