alarm MITSUBISHI LANCER 2010 8.G User Guide
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2010, Model line: LANCER, Model: MITSUBISHI LANCER 2010 8.GPages: 670, PDF Size: 25.18 MB
Page 155 of 670
3-64 Features and controls
3
At this time, the theft-alarm indicator (A) on the audio
panel flashes for confirmation.
4. The system has entered the armed stage after about 20
seconds, when the theft-alarm indicator (A) flashing
becomes slower.
The theft-alarm indicator (A) continues to flash while the
system is in the armed stage.
NOTEThe system will be disarmed if, while the theft-alarm indi-
cator (A) is illuminated, all doors are unlocked by remote
control transmitter, the F.A.S.T.-key.
The system will be disarmed if, while the theft-alarm indi-
cator is illuminated, the ignition switch is turned to “ON”
or “ACC”.
The system will not be armed if a door or a trunk lid is not
completely closed. If this happens, rearm the system as
described above.
The driver should not arm the system until first confirm-
ing that all passengers have left the vehicle. If the driver
arms the system with passenger(s) in the vehicle, the
alarm may be activated when the passenger(s) open the
door.
BK0102103US.book 64 ページ 2009年10月26日 月曜日 午後1時38分
Page 156 of 670
Features and controls
3-65
3
Alarm stageWhile the vehicle is parked and the system is armed, the alarm
will be activated if one of the doors or a trunk lid is opened
without the remote control transmitter or the F.A.S.T.-key.Type of alarmWhen the alarm is activated:
1. The headlights blink on and off for 3 minutes.
After 3 minutes the headlights automatically shut off.
2. The horn will sound intermittently for 3 minutes.
NOTEThe alarm will continue to operate for 3 minutes. At the
end of that period, the alarm will automatically shut off to
save battery power. The system will then be rearmed until
the proper disarming step is taken.
While the alarm is operating, it is displayed on the infor-
mation screen in the multi-information display.
Ty p e 1
Ty p e 2Alarm deactivationThe alarm can be deactivated in the following ways.
By using the remote control transmitter or the F.A.S.T.-
key to lock or unlock the door.
Turn the ignition switch to the “ON” or the “ACC” posi-
tion.
Horn sounds!
Headlights blink on and off!
BK0102103US.book 65 ページ 2009年10月26日 月曜日 午後1時38分
Page 157 of 670
3-66 Features and controls
3
Disarmed stageThe system will be disarmed when either of the following steps
are taken:
1. All doors are unlocked by the remote control transmitter,
the F.A.S.T.-key.NOTEIf the UNLOCK button is pressed when all doors are
closed and no door is opened within approximately 30
seconds, re-arming will automatically occur.
2. The ignition switch is turned to the “ACC” or “ON” posi-
tion.NOTEOnce the system has been disarmed, it cannot be rearmed
except by repeating the arming procedure.
Testing the theft-alarm systemUse the following procedure to test the system:
1. Lower the driver’s window.
2. Arm the system as explained in “Armed stage”.
3. Make sure that the theft-alarm indicator comes on and
flashes within approximately 20 seconds.
4. Wait a few seconds and then unlock the driver’s side door
by using the inside door lock knob and opening the door.
5. Check to be sure that the horn sounds intermittently and
the headlights blink on and off when the doors is opened.
6. Disarm the system by unlocking all doors by the remote
control transmitter, the F.A.S.T.-key.
Disarm...by remote control transmitter or F.A.S.T.-keyBK0102103US.book 66 ページ 2009年10月26日 月曜日 午後1時38分
Page 223 of 670
3-132 Features and controls
3
Power brakes
N00517600377
Your vehicle is equipped with power brakes for more braking
force with minimal brake pedal effort.
Your brakes are designed to operate at full capacity, even if the
power assist is lost.
If the power assist is lost, the effort needed to press the brake
pedal is greater.
If you should loose the power assist for some reason, the
brakes will still work.
If the power brake unit or either of the two brake hydraulic sys-
tems stops working properly, the rest of the brake system will
still work, but the vehicle will not slow down as quickly.
You will know this has happened if you find you need to
depress the brake pedal down further, or harder when slowing
down or stopping, or if the brake warning light and the warning
display in the multi-information display come on.
Brake pad wear alarm
N00532500087
The disc brakes have an alarm that makes a metallic squeal
when the brake pads have worn down enough to need service.
If you hear this sound, have the brake pads replaced at an
authorized Mitsubishi Motors dealer or a repair facility of your
choice.
WARNING
!Never coast downhill with the engine OFF. Keep the
engine running whenever your vehicle is in motion.
If you turn off the engine while driving, the power
brake booster will stop working and your brakes
will not work as well.If the power assist is lost or if either brake hydraulic
system stops working properly, take your vehicle to
an authorized Mitsubishi Motors dealer or a repair
facility of your choice immediately.
WARNING
!Driving with worn brake pads will make it harder to
stop, and can cause an accident.
BK0102103US.book 132 ページ 2009年10月26日 月曜日 午後1時38分
Page 284 of 670
Features and controls
3-193
3
3. Press and hold the multi-information meter switch (for
about 2 seconds or more) to switch in sequence from ON
(operation sound on) → OFF (operation sound off) → ON
(operation sound on).
The setting is changed to the selected condition.NOTEIf the battery is disconnected, the memory of the operation
sound setting is erased and is automatically set to “ON”
(operation sound on).
The operation sound setting only deactivates the operation
sound of the multi-information meter switch and rheostat
meter illumination button. The warning display and other
sounds cannot be deactivated.
Changing the amount of time until “REST
REMINDER” is displayed
N00557500062
The amount of time until the display appears can be changed.
1. Press and hold the multi-information meter switch (for
about 2 seconds or more) to switch from the setting mode
screen to the menu screen.
Refer to “Changing the function settings (With ignition
switch in the “ON” position)” on page 3-184.
2. Lightly press the multi-information meter switch to select
“ALARM” (rest time setting).Type 1
Type 2
BK0102103US.book 193 ページ 2009年10月26日 月曜日 午後1時38分
Page 285 of 670
3-194 Features and controls
3
3. Press and hold the multi-information meter switch (for
about 2 seconds or more) to display “ALARM” (rest time
setting).
4. Lightly press the multi-information meter switch to select
the amount of time until the display appears.
5. Press and hold the multi-information meter switch (for
about 2 seconds or more) to change the setting to the
selected time.NOTEIf the battery is disconnected, the memory of the unit set-
ting is erased and is automatically set to the “OFF”.
The drive time is reset when the ignition switch is in the
“OFF” position.
Changing the turn-signal sound (Type2)
N00563500012
It is possible to change the turn-signal sound.
1. Press and hold the multi-information meter switch for
about 2 seconds or more to switch from the setting mode
screen to the menu screen.
Refer to “Changing the function settings (With ignition
switch in the “ON” position)” on page 3-184.
2. Lightly press the multi-information meter switch to select
. (changing the turn-signal sound)
3. Press and hold the multi-information meter switch for
about 2 seconds or more to switch in sequence from 1
(turn-signal sound 1) → 2 (turn-signal sound 2) → 1
(turn-signal sound 1).
The setting changes to the selected turn-signal sound.
Type 1 Type 2BK0102103US.book 194 ページ 2009年10月26日 月曜日 午後1時38分
Page 291 of 670
3-200 Features and controls
3
Warning display list (With ignition switch in the “OFF” position)
N00558000110
Screen type 1
Screen type 2
Cause
Do this (Reference)
You have forgotten to remove the
key from the ignition switch.Remove the key.
Refer to “Key reminder system” on
page 3-54.
You have forgotten to turn off the
lights.Refer to “Light auto-cutout function
(headlights and other lights)” on
page 3-220.
The theft-alarm is operating.Refer to “Theft-alarm system” on
page 3-63.
Immobilizer is registered.Refer to “Electronic immobilizer
(Anti-theft starting system)” on
page 3-5, 3-42.
BK0102103US.book 200 ページ 2009年10月26日 月曜日 午後1時38分
Page 663 of 670
Alphabetical index
6Rear turn signal lights
Bulb capacity 7-56
Replacement 7-80
Rear window defogger switch 3-235
Rearview mirror
Inside 3-77
Outside 3-79
Refrigerant (air conditioning) 9-11
Replacement of light bulbs 7-56
Replacing tires and wheels 7-34
Reporting Safety Defects 8-3
Roof antenna 5-122
,5-123
S
Safe driving techniques 4-4
Seat 2-2
Arm rest 2-9
Front seats 2-3
Heated seats 2-7
Rear seats 2-8
Seats and restraint systems 2-3
Seat belt 2-14
Adjustable seat belt shoulder anchor 2-20
Child restraint 2-24
Driver’s seat belt reminder/warning 2-18
Force limiter 2-23
Front passenger seat belt warning light 2-19
Maintenance and inspection 2-34
Pre-tensioner 2-22Seat belt extender 2-21
Seat belt instructions 2-15
Seat belt use during pregnancy 2-21
Service brake 3-131
Service precautions 7-2
Snow tires 7-37
Spark plugs 7-41
Starting
At extremely cold ambient temperature 3-87
Flooded engine 3-33
,3-41
,3-88
Normal conditions 3-86
Steering
Power steering fluid 7-22
,9-11
Tilt lock lever 3-76
Wheel lock 3-30
,3-84
Steering wheel audio remote control switch 5-112
Storage spaces 3-277
Front console boxes 3-280
Sun visors 3-268
Supplemental Restraint System 2-35
How the Supplement Restraint System works 2-39
Servicing 2-58
Warning light/display 2-43
T
Tank capacity 1-5
,9-11
Theft-alarm system 3-63
Tire pressure monitoring system 3-152
Warning light/display 3-153
BK0102103US.book 6 ページ 2009年10月26日 月曜日 午後1時38分