dimensions MITSUBISHI LANCER EVOLUTION IV 1998 Workshop Manual

42-1
BODY
CONTENTS
HOOD 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FENDER 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRUNK LID 4. . . . . . . . . . . .
BODY CONSTRUCTION
(Difference between
EVOLUTION-IV and V) 5. . . . . . . . . . . . . . . . . . . TYPE A (PROJECTED DIMENSIONS) 7. . . . .
TYPE B (ACTUAL-MEASUREMENT
DIMENSIONS) 11. . . . . . . . . . . . . . . . . . . . . . . . . .

BODY – Body Construction (Difference between EVOLUTION-IV and V)42-5
BODY CONSTRUCTION
(Difference between EVOLUTION-IV and V)
EVOLUTION-V has a different rear suspension configuration from that of EVOLUTION-IV because of
adoption of reinforced suspension elements and wide tread tyres. For this reason, the configuration and
the dimensions of the following body sections are also different.
SIDE BODY
Side Structure
(1) The quarter panel has a cut-out provided at the inner section.
(2) The quarter inner extension front and the quarter inner extension rear is provided in the quarter
panel inner cut-out section.
Cut-out
Quarter panel inner


Quarter inner
extension front
Quarter inner
extension rear

BODY –
Body Dimension
42-7
BODY DIMENSION
TYPE A (PROJECTED DIMENSIONS)
The reference dimensions of the under body have been changed as follow. Those of the other body sections remain unchanged.
Unit: mm
913
10
1
8
79
32
950829714173157329
329
1,232810
703
544
940
216
1
23
7
810
9
4
216
1
indicates that the dimension and the measurement point are the same as
those for EVOLUTION-IV.
4
8383580
251
572911249329419671
1,211
60
245
230
UNDER BODY

BODY –
Body Dimension
42-9
Unit: mmSUSPENSION INSTALLATION DIMENSIONS
Center of vehicle
Center
of
vehicle
indicates that the dimension and
the measurement point are the
same as those for EVOLUTION-IV.
2122
6965
13
12
11
72
71
7069
2122
20
20
12
11
13
6523
2
852700810862829597930
290
270
572
132
401
523
623
230
240239
529
529
1,145
1,0931,1861,010
1136’
641
242
75
7891
3
4
1
60
6

BODY –
Body Dimension
42-11
TYPE B (ACTUAL-MEASUREMENT DIMENSIONS)
indicates that the dimension and the measurement point are the same as those for EVOLUTION-IV.
Unit: mmUNDER BODY
10
23
79
6
6
8
1
8
9
7
32
1
21
21
10
1,6351,028
1,231
1,3951,287
719
544933
962
1,232829714191
329
329
175950
900
871660
708
4
940810
4

BODY –
Body Dimension
42-13
SUSPENSION INSTALLATION DIMENSIONS
indicates that the dimension and the measurement point are the same as those for EVOLUTION-IV.
Unit : mm
2
21
2
13
1222
20
65
21
20
65
22
12
13
1,210
329
1,186862930597829700810
938
35211 7
842
826
1,069

EXTERIOR – Mark 51-16
2. brembo MARK
Application tape edge
Rear bumper lineTrunk lid opening line
3. EVOLUTION-V MARK (REAR)
Trunk lid opening line
Rear bumper line
(2) Installation procedure
1. Using unleaded gasoline, degrease the surface of the body on which the marks are mounted.
2. Peel off the release paper from the back side of the mark and affix the mark, ensuring the specified
dimensions are met.
Caution
(1) Perform the procedure in a dust-free place with an ambient temperature ranging from
20 to 38C.
(2) If the ambient temperature is below 20C, heat the mark and mounting position to 20
to 30C.
(3) Be sure to press each mark positively, as a low pressure results in the mark being
separated easily.