engine oil MITSUBISHI LANCER EVOLUTION IV 1998 Workshop Manual

MITSUBISHI LANCER EVOLUTION IV 1998 Workshop Manual LANCER EVOLUTION IV 1998 MITSUBISHI MITSUBISHI https://www.carmanualsonline.info/img/19/57322/w960_57322-0.png MITSUBISHI LANCER EVOLUTION IV 1998 Workshop Manual

Page 7 of 396

MITSUBISHI LANCER EVOLUTION IV 1998  Workshop Manual 11-1
ENGINE
CONTENTS
SERVICE SPECIFICATIONS 2. . . . . . . . . . . . . . 
SEALANTS 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
SPECIAL TOOLS 2 . . . . . . . . . . . . . . . . . . .

Page 8 of 396

MITSUBISHI LANCER EVOLUTION IV 1998  Workshop Manual ENGINE – Service Specifications / Sealants / Special Tools11-2
SERVICE SPECIFICATIONS
ItemsStandard valueLimit
Basic ignition timing5 BTDC ± 3–
Ignition timing (at idle)Approx. 5 BTDC–
Idle

Page 9 of 396

MITSUBISHI LANCER EVOLUTION IV 1998  Workshop Manual ENGINE – Special Tools11-3
Tool UseName Number
MD998719Crankshaft pulley
holder pinHolding the crankshaft pulley
Holding the camshaft sprocket
MD998715Pulley holder pin
MD998713Camshaft oil seal
i

Page 11 of 396

MITSUBISHI LANCER EVOLUTION IV 1998  Workshop Manual ENGINE – Engine Adjustments11-5
2. AUTO TENSIONER CHECK
(1) Stop the engine from the idle speed and check that the
belt rests within the auto tensioner pulley width.
(2) Remove the drive belt.
(For

Page 13 of 396

MITSUBISHI LANCER EVOLUTION IV 1998  Workshop Manual ENGINE – Engine Adjustments11-7
4. LASH ADJUSTER REPLACEMENT
Refer to (4) of the preceding paragraph.
5. IGNITION TIMING CHECK
Check that ignition timing is at the standard value.
Standard value: ap

Page 14 of 396

MITSUBISHI LANCER EVOLUTION IV 1998  Workshop Manual ENGINE – Engine Adjustments11-8
(5) Set compression gauge to one of the spark plug holes.
(6) Crank the engine with the throttle valve fully open and
measure the compression pressure.
Standard value

Page 16 of 396

MITSUBISHI LANCER EVOLUTION IV 1998  Workshop Manual ENGINE – Camshaft and Camshaft Oil Seal11-10
CAMSHAFT AND CAMSHAFT OIL SEAL
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
(1) Engine Coolant Draining and Refilling
(2) Air Hos

Page 17 of 396

MITSUBISHI LANCER EVOLUTION IV 1998  Workshop Manual ENGINE – Camshaft and Camshaft Oil Seal11-11
Grease  and adhesive application points
Timing belt side
Semi-drying  sealant: THREEBOND 1207D
Lip 10 mm
10 mm10 mm
Semi-drying  sealant: 
THREEBOND 1207

Page 18 of 396

MITSUBISHI LANCER EVOLUTION IV 1998  Workshop Manual ENGINE – Camshaft and Camshaft Oil Seal11-12
BCAM CAP / REAR CAP / FRONT CAM CAP
INSTALLATION
(1) Locate the camshaft dowel pins as illustrated.
(2) Temporarily tighten cam cap in two to three ste

Page 19 of 396

MITSUBISHI LANCER EVOLUTION IV 1998  Workshop Manual ENGINE – Oil Pan11-13
OIL PAN
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
(1) Under Cover Removal and Installation
(2) Front Exhaust Pipe Removal and Installation 
(Refer to
Page:   1-10 11-20 21-30 31-40 41-50 ... 60 next >