parking brake MITSUBISHI LANCER EVOLUTION IV 1998 Workshop Manual

00
11
12
13
14
15
16
17
21
22
26
27
32
33
34
35
36
37
42
51
54
General . . . . . . . . . . . . . . . . . . . . . . . .
Engine . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Lubrication . . . . . . . . . . . . .
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Cooling . . . . . . . . . . . . . . . . .
Intake and Exhaust . . . . . . . . . . . .
Engine Electrical . . . . . . . . . . . . . . .
Engine and Emission Control . . . .
Clutch . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Transmission . . . . . . . . . . .
Front Axle . . . . . . . . . . . . . . . . . . . . . .
Rear Axle . . . . . . . . . . . . . . . . . . . . . .
Power Plant Mount . . . . . . . . . . . . . .
Front Suspension . . . . . . . . . . . . . . .
Rear Suspension . . . . . . . . . . . . . . .
Service Brakes . . . . . . . . . . . . . . . . .
Parking Brakes . . . . . . . . . . . . . . . . .
Steering . . . . . . . . . . . . . . . . . . . . . . . .
Body . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exterior . . . . . . . . . . . . . . . . . . . . . . . .
Chassis Electrical . . . . . . . . . . . . . .
Electrical Wiring . . . . . . . . . . . . . . . .
WORKSHOP MANUAL
FOREWORD
This Workshop Manual contains procedures for
service mechanics, including removal, disassembly,
inspection, adjustment, reassembly and
installation. Figures taken from registration
documents are given in metric units only. All other
figures are given in SI units with metric units in
brackets. Use the following manuals in combination
with this manual as required.
TECHNICAL INFORMATION MANUAL
N9806CNCP9
All information, illustrations and product
descriptions contained in this manual are current
as at the time of publication. We, however, reserve
the right to make changes at any time without prior
notice or obligation.
July 1998
EVOLUTION-IV
EVOLUTION-V

REAR AXLE – On-vehicle Service 27-27
ON-VEHICLE SERVICE

1. REAR AXLE TOTAL BACKLASH CHECK
If the drive system roars or the vehicle vibrates, use the
following procedure to measure total backlash in the rear
axle. Based on the measurement taken, determine whether
the differential carrier assembly needs to be removed or not.
(1) Place the shift lever in the neutral position and operate
the parking brake.
(2) Turn the propeller shaft fully clockwise and make an
alignment mark on the companion flange dust cover and
gear carrier.
(3) Turn the propeller shaft fully counterclockwise and
measure the deviation between the alignment marks.
Limit: 5 mm
(4) If the backlash exceeds the limit, replace the differential
carrier assembly.
2. GEAR OIL LEVEL CHECK
2-1 DIFFERENTIAL
(1) Remove the filler plug.
(2) Check that the gear oil level is within the specified range
from the bottom end of the filler plug hole.
Standard value (A): 6 mm
(3) If the gear oil level exceeds the standard value, add the
specified gear oil up to the bottom end of the filler plug
hole.
Specified gear oil:
MITSUBISHI GENUINE DIA QUEEN SUPER
HYPOID GEAR OIL (GL-5)
NOTE
10
C or more: #90, less than 10
C: #80
(4) Fit the filler plug and tighten it to the specified torque.
Alignment marks
Filler plug
49 Nm
{5.0 kgf
m}
Gear oil
Upper
limit
Lower
limit

REAR AXLE – On-vehicle Service 27-31
7. SPEED SENSOR OUTPUT VOLTAGE
MEASUREMENT ABS>
(1) Lift up the vehicle and release the parking brake.
(2) Disconnect the AYC-ECU harness connector and take
measurements on the harness side connector.
Caution
Insert the probe from the harness side with the double
lock of the connector unlocked. Inserting it to the
terminal side could result in poor contact.
(3) Turn the wheel to be tested at about 1/2 to one
revolution/sec. and check for the output voltage using
a circuit tester (AC mV range) or oscilloscope.
Terminal nos.
Front LHFront RHRear LHRear RH
7698
20192221
Output voltage:
When circuit tester is used: 70 mV or more
When oscilloscope is used: 200 mVp-p or more
(4) If the output voltage is lower than the above value, it
is probably attributable to the following faults. Check or
replace the speed sensor as necessary.
Excessive clearance between the pole piece and rotor
of the speed sensor
Defective speed sensor
Waveform Check Using Oscilloscope
Check the harness and connector of the speed sensor for
connection. Then, use an oscilloscope to check for output
voltage waveform of each speed sensor as follows.
Start the engine and monitor the sensor by turning the wheel;
for a driving wheel, let it turn by shifting into the 1st gear
and for a driven wheel turn it manually at a constant speed.
NOTE
(1) Waveform may be observed by actually running the
vehicle.
(2) The output voltage is low when the wheel speed remains
low and builds up as the wheel speed increases.
AYC-ECU connector harness side
When turned manually
At idle (5 to 6 km/h)
1st gear

REAR AXLE – Rear Hub Assembly27-33
REAR HUB ASSEMBLY
REMOVAL AND INSTALLATION
12
3
4
56 7
8
Unit: Nm {kgf
m}
118 {12.0}
74 – 88
{7.5 – 9.0} 49 – 59
{5.0 – 6.0}196 – 255
{20.0 – 26.0}
Removal steps
A1. Caliper assembly
2. Brake disc
3. Shoe & lining assembly
(Refer to GROUP 36 – Parking
Brake.)
4. Clip
5. Parking brake cable connectionBA6. Drive shaft nut
C7. Rear hub assembly
8. Backing plate
Caution
Do not disassemble the rear hub assembly.
REMOVAL SERVICE POINTS
ACALIPER ASSEMBLY REMOVAL
Secure the removed caliper assembly with a wire so that
it will not fall.
BDRIVE SHAFT NUT REMOVAL
CREAR HUB ASSEMBLY REMOVAL
(1) Using the special tool, remove the drive shaft from the
rear hub assembly.
(2) Remove the mounting bolts and remove the rear hub
assembly from the knuckle.
MB990767
MB990244 (3) MB990767
MB990242MB991354

REAR AXLE – Drive Shaft27-36
DRIVE SHAFT
REMOVAL AND INSTALLATION
Pre-removal Operation
(1) Gear Oil Draining (Refer to P.27-28.)
(2) Center Exhaust Pipe Removal
(Refer to GROUP 15.)Post-installation Operation
(1) Checking Each Ball Joint Dust Cover for Cracks
and Damages by Pressing Dust Cover with Finger
(2) Center Exhaust Pipe Installation
(Refer to GROUP 15.)
(3) Gear Oil Filling (Refer to P.27-28.)
(4) Parking Brake Lever Stroke Check and Adjustment
(Refer to GROUP 36 – On-vehicle Service.)
(5) Wheel Alignment Check and Adjustment
(Refer to GROUP 34 – On-vehicle Service.)
1
2 3
4
56 7
89 10 11
Unit: Nm {kgf
m}
25 {2.6}
74 – 87 {7.5 – 8.9}
74 – 87
{7.5 – 8.9}*88 {9.0}* 49 – 59 {5.0 – 6.0}
196 – 255 {20.0 – 26.0}
Removal steps
1. Caliper assembly
(Refer to P.27-33.)
2. Brake disc
3. Shoe & lining assembly (Refer to
GROUP 36 – Parking Brake.)
4. Clip
5. Parking brake cable connection
AB6. Drive shaft nut
7. Rear speed sensor coupling

8. Trailing arm coupling
9. Lower arm coupling
10. Toe control arm coupling
BA11. Drive shaftCaution
(1) With the part marked with *, first temporarily
tighten it, then ground the vehicle and tighten
it to specification in unloaded condition.
(2) When removing the drive shaft from, and
reinstalling it to, a vehicle with AYC, use care
not to damage the rotor mounted on the BJ outer
race.

REAR SUSPENSION – Rear Suspension Assembly34-4
REAR SUSPENSION ASSEMBLY
REMOVAL AND INSTALLATION
Pre-removal Operation
(1) Center Exhaust Pipe Removal
(Refer to GROUP 15.)
(2) Trunk Room Side Trim Removal
(3) AYC Fluid Draining
(Refer to GROUP 27 – On-vehicle Service.)Post-installation Operation
(1) AYC Fluid Refilling and Bleeding
(Refer to GROUP 27 – On-vehicle Service.)
(2) Center Exhaust Pipe Installation
(Refer to GROUP 15.)
(3) AYC Operation Check
(4) Parking Brake Cable Stroke Check
(Refer to GROUP 36 – On-vehicle Service.)
(5) Wheel Alignment Check and Adjustment
(Refer to P.34-3.)
1
34
5
6
7 9 10
1112
1314
15 1617
Unit: Nm {kgf
m}
44 {4.5}
108 – 127 {11.0 – 13.0}
54 {5.5}
88 {9.0}
93 {9.5}*88 {9.0}
158 2
15
29 – 34
{3.0 – 3.5}
25 {2.6}34 {3.5}25 {2.5}
69
{7.0} Toe control bar
EVOLUTION-V RS
137 – 156 {14.0 – 16.0}*59 – 68 {6.0 – 7.0}*
Removal steps
1. Fuel filler cap
2. Bolt
3. Filler neck protector
4. Cap
5. Shock absorber mounting nut
A6. Brake caliper assembly
7. Rear speed sensor AYC>
8. Brake disc
9. Parking brake cable end (Refer to
GROUP 36.)
10. AYC fluid line connection with AYC>BB11. Propeller shaft connection
12. Upper arm mounting bolt
13. Trailing arm mounting bolt
14. Toe control arm mounting bolt
CA15. Crossmember mounting bolt
16. Differential support assembly
mounting bolt
17. Rear suspension assembly
Caution
The parts marked with * should be first temporarily
tightened, then torqued to specification with the
vehicle on the ground in unloaded condition.

REAR SUSPENSION – Trailing Arm Assembly34-8
TRAILING ARM ASSEMBLY
REMOVAL AND INSTALLATION
Post-installation Operation
(1) Push the Dust Cover of the Trailing Arm Ball Joint
with a Finger to Check for Possible Cracks or
Damage.
(2) Wheel Alignment Check and Adjustment
(Refer to P.34-3.)
1
2 3
45
Unit: Nm {kgf
m}
74 – 87 {7.5 – 8.9}
137 – 156 {14.0 – 16.0}*
4
Removal steps
1. Parking brake cable bolt
A2. Trailing arm assembly to knuckle
coupling
3. Trailing arm assembly mounting
bolt
4. Stopper
5. Trailing arm assemblyCaution
The part marked with * should be first temporarily
tightened, then torqued to specification with the
vehicle on the ground in unloaded condition.
REMOVAL SERVICE POINT
ATRAILING ARM ASSEMBLY DISCONNECTION
FROM KNUCKLE
Caution
(1) Only loosen the nut, and not remove it from the ball
joint, and use the special tool.
(2) Hang the special tool with a string to prevent the
parts including the tool from falling apart.
MB990635,
MB991113 or
MB991406
NutString
Ball joint

BASIC BRAKE SYSTEM – On-vehicle Service35A-3
If the free play exceeds the standard value, it is probably
due to excessive play between the retaining ring bolt
and brake pedal arm.
Check for excessive clearance and replace faulty parts
as required.
4. Start the engine, depress the brake pedal with
approximately 490 N of force, and measure the clearance
between the brake pedal and the floorboard.
Standard value: 80 mm or more
If the clearance is outside the standard value, check for
air trapped in the brake line, clearance between the lining
and the drum and dragging in the parking brake.
Adjust and replace defective parts as required.
5. Turn back the carpet, etc.

36-1
PARKING
BRAKES
CONTENTS
SERVICE SPECIFICATIONS 2. . . . . . . . . . . . . .
LUBRICANTS 2. . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS 2. . . . . . . . . . . . . . . . . . . . . . . . ON-VEHICLE SERVICE 3. . . . . . . . . . . . . . . . . .
1. Parking Brake Lever Stroke Check and
Adjustment 3. . . . . . . . . . . . . . . . . . . . . . . . . . .
2. Lining Running-in 4. . . . . . . . . . . . . . . . . . . . . .
PARKING BRAKE CABLE 5. . . . . . . . . . . . . . .
PARKING BRAKE DRUM 7. . . . . . . . . . . . . . . .

PARKING BRAKE – Service Specifications / Lubricants / Special Tools36-2
The parking brake is designed as a drum-in-disc brake acting on the rear wheel. This brake is a little
different in construction between EVOLUTION-IV and EVOLUTION-V but much alike in the service procedure
of the parking brake section. In this group, therefore, the description is made only for EVOLUTION-IV.
SERVICE SPECIFICATIONS
ItemsStandard valueLimit
Parking brake lever stroke (operating force approx. 196 N {20 kgf})5 – 7 notches–
Brake lining thickness mm2.81.0
Brake drum I.D. mm168169
LUBRICANTS
ItemsSpecified lubricantQuantity
Backing plateCHUO YUKA AKB100As required
Shoe & lining assembly
Adjuster
SPECIAL TOOLS
ToolNumberNameUse
MB990767End yoke holderFixing of hub
MB990241
A: MB990242
B: MB990244Axle shaft puller
A: Puller shaft
B: Puller barRemoval of drive shaft
MB991354Puller body