diagram MITSUBISHI LANCER EVOLUTION IX 2005 User Guide

ENGINE – TIMING BELT, TIMING BELT B11-26



F 
Fitting the timing belt
1. Check that all the timing marks for the camshaft sprocket, the
crankshaft sprocket and the oil pump sprocket are aligned.
2. After the timing marks for the oil pump sprocket have been
aligned, remove the plug from the cylinder block and insert a
posidrive (+) with a diameter of 8 mm into the plug hole. Check
that more than 60 mm of the shaft of the screwdriver can be
inserted. If the screwdriver strikes the balancer shaft and can
only be inserted to a depth of 20 ~ 25 mm, turn the sprocket one
complete turn, realign the timing marks, and check that more
than 60 mm of the screwdriver can be inserted. Do not remove
the screwdriver until the timing belt has been fitted.
3. Install the timing belt in accordance with the following guidelines
so that the side that is under tension does not get slack.
(1) Fit the timing belt around the crankshaft sprocket first, then
the oil pump sprocket and then fit it around the idler pulley.
(2) Fit the timing belt around the camshaft sprocket (exhaust
side) and hold it in place with a paper clip at the position
shown in the diagram.
timing marks
camshaft
sprocket (inlet
side)
timing
marks
crankshaft
sprocket
camshaft
sprocket
(exhaust
side)
timing
marks
oil pump
sprocket
plug
more than
60 mm
screwdriver
balancer shaft
camshaft
sprocket (inlet
side)
tensioner pulley
crankshaft
sprocket
camshaft
sprocket
(exhaust side)
idler
pulley
oil pump
sprocket
paper
clip

ENGINE – TIMING BELT, TIMING BELT B
11-27
(3) Use a wrench to align the timing marks on the rocker cover and
the camshaft sprocket, and whilst doing so, fit the timing belt
around the camshaft sprocket (inlet side) and hold it in place
with a paper clip at the position shown in the diagram.
(4) Fit the timing belt around the tensioner pulley.
(5) Remove the two paper clips.
Caution
After the timing belt has been installed, apply some force in
an anti-clockwise direction to the camshaft sprocket and
check once more that all the timing marks are in the correct
position when the side of the belt under tension is taught.
4. Using the special wrench for the tensioner pulley socket
(MD998767), tense the timing belt by turning the tensioner
pulley in the direction shown in the diagram, and temporarily
tighten the mounting bolt for the tensioner pulley.
5. Check that all the timing marks are aligned.
6. Remove the screwdriver, and replace the plug.
7. Adjust the tension of the timing belt.



G 
Adjusting the tension of the timing belt
1. Remove the rubber plug from the rear cover of the timing belt
and put the special adjusting bolt (MD998738) in position.
Slowly twist the adjusting bolt a little at a time, so that the wire
or pin inserted when fitting the auto-tensioner, only moves a
little.
Caution
There is a possibility that the wire or pin inserted in the
auto-tensioner may break if the adjusting bolt is twisted
with a spanner or a similar tool, so it must be twisted by
hand.
2. Turn the crankshaft a quarter turn in an anti-clockwise direction.
3. Turn the crankshaft in a clockwise direction, realign all the timing
marks and set the No.1 cylinder in the top dead centre position.
4. Loosen the mounting bolt for the tensioner pulley which had
been temporarily tightened.paper clips

ENGINE – TIMING BELT, TIMING BELT B, ENGINE ASSY11-28
5. Using the special wrench for the tensioner pulley socket
(MD998767) or a torque wrench, apply tension torque (3.5 N·m)
to the timing belt in the direction shown in the diagram, and
tighten the mounting bolt for the tensioner pulley to the specified
torque.
Tightening torque: 48 ± 5 N·m
Caution
When tightening the installed bolt, take care that the
tensioner pulley does not turn around with it. If the pulley
does turn around with the bolt, the tension of the belt will
become too strong.
6. Remove the wire or pin which had been inserted when the auto-
tensioner was fitted.
7. Remove by hand the special adjusting bolt (MD998738) which
had been fitted in step 1.
8. Turn the crankshaft two complete turns in a clockwise direction,
and leave it for about 15 minutes.
9. Reinsert the wire or pin which had been removed in step 6, and
check that it can be easily pulled out again.
If the wire or pin can be easily pulled out the tension of the
timing belt is just right, so the wire or pin should be removed
completely. At this point check that the auto-tensioner rod is not
projecting more than the amount specified.
Specified projection (A): 3.8 ~ 4.5 mm
10. If the wire or pin cannot be easily pulled out, repeat steps 1 to 8
until the tension of the timing belt is just right.
11.Recheck that the timing marks on all of the sprockets are in line.
Caution
If the crankshaft bolt is turned in an anti-clockwise
direction, the tightening torque of the crankshaft bolt must
be checked, and if it is loose, it must be retightened.
ENGINE ASSY
Removal and fitting
Jobs to be completed before removal and after fitting
•Measures to prevent fuel leaking.
•Check for fuel dripping.
•Removal and refitting of the bonnet.
•Removal and refitting of the strut tower bar.
•Removal and refitting of the valence. (Ref Section 51: Front bumper)
•Checking the tension of the drive belt.
•Adjustment of the axle letter cable.
•Draining and replacing the engine oil.
•Draining and replacing the coolant.
•Removal and refitting of the air cleaner.
•Removal and refitting of air pipe C.
•Removal and refitting of the battery and the battery tray.
•Removal and refitting of the centre cover. (Ref P11-5)
•Removal and refitting of the axle letter cable.
•Removal and refitting of the radiator.
•Removal and refitting of the front exhaust pipe.

ENGINE – ENGINE ASSY
11-33



B 
Fitting the engine mount bracket & stopper ASSY
1. Support the engine oil pan component with the garage jack
through the engine block, and fit the engine mount bracket &
stopper ASSY whilst checking the position of the engine. Fix the
engine mount stopper so that the arrow points in the direction
shown in the diagram.
2. Support the engine ASSY with a garage jack.
3. Remove the chain block.
4. In the same way as when it was removed, hold the engine
ASSY with the special tool.
(1) (MZ203830 or MZ203831)>
Install the special mechanical engine hanger (MZ203830
or MZ203831).
(2)
Fit the following parts to the base hanger.
• Slide bracket (HI)
• Foot (standard) (MB991932)
• Joint (90) (MB991930)
Install the special engine hanger (MB991928)



C 
Fitting the transfer ASSY and the transmission ASSY
1. Fit the transfer ASSY and the transmission ASSY.
2. Remove the radiator support upper insulator mounting bolts from
the chassis (2 places).engine sideengine side
engine mount stopper
rear of chassis> front of chassis>
MZ203830 or MZ203831
slide bracket (HI)
front of
chassis
joint (90)
(MB991930)
foot (standard) (MB991932)
slide bracket (HI)

MPI – GENERAL
13A-1
SECTION 13A
MPI (Multi-point Fuel Injection)
CONTENTS
General ..................................................................... 2
Servicing standards .................................................3
Special tools ............................................................3
Troubleshooting ......................................................5Servicing the vehicle ............................................29
1. Adjusting specified revolutions when idling.....29
2. MPI system components layout diagram ........29
3. Checking the air temperature sensor..............29
4. Checking the oil feeder control valve..............30
GENERAL
Servicing guidelines have been changed because of the changes listed below.
•Avariable valve timing control system (V.V.T.) has been adopted. Because of this, an oil feeder control valve and an intake
cam position sensor have been added.
•Amanifold absolute pressure (MAP) sensor has been added.
•An air temperature sensor has been added.

MPI – GENERAL13A-2
MPI system diagram
Engine ECU
H1. O
2 sensor
H2. Air flow sensor
H3. Intake air temp.
sensor
H4. Throttle position
sensor
H5. Intake Cam position
sensor
H6. Exhaust Cam
position sensor
H7. Crank angle
sensor
H8. Atmospheric
pressure sensor
H9. Water temp.
sensor
H10. Knock sensor
H11. Manifold absolute
pressure (MAP)
sensor
H12. Air temp. sensor• Power supply
• Ignition switch IG
• Ignition switch ST
• Vehicle speed
sensor
• A/C switch
• A/C load signal
• Power steering
fluid pressure switch
• Alternator FR signal
• Inter-cooler water spray
switch (auto)
•Inter-cooler water spray
switch (manual)I1. Injector
I2. ISC servo (Stepper
motor)
I3. Fuel pressure
control solenoid valve
I4. No. 1 Waste gate
solenoid valve
I5. No. 2 Waste gate
solenoid valve
I6. Purge control
solenoid valve
I7. Secondary air
control solenoid valve
I8. Oil feeder control
valve• Engine control relay
• Fuel pump relay 2,3
(ON/OFF)
• Fuel pump relay (HI/LO
switch)
• A/C relay
• Ignition coil
• Fan controller
• Condenser fan relay (HI)
• Condenser fan relay
(LO)
• Engine warning light
• Diagnosis output
terminal
• Alternator G terminal
• Inter-cooler water spray
relay
•Inter-cooler water spray
lamp
• O
2sensor heater
ÈÈ
I 6. Purge control
solenoid valve
I 7. Secondary
air control
solenoid valveCheck
valve
Secondary air
valve
To fuel
tank
H 6. Exhaust cam
position sensor
H 8. Atmospheric
pressure sensor
H 2. Air flow sensor
Intake
Waste gate actuator
I 4. No.1 waste gate
solenoid valve H 3. Intake air
temperature
sensor
I 5. No.2 waste gate
solenoid valve
H 1. O
2sensor
H 5. Intake cam
position sensorCatalyst
H 7. Crank angle sensor
H 10. Knock sensor
H 9. Water temperature sensor
I 1. Injector From fuel
pump
Fuel pressure
regulatorI 8. Oil feeder control
valve I 3. Fuel pressure
control solenoid
valve
Vacuum
tank
I 2. ISC servoH 11. MAP sensor
H 12. Air temperature sensor
H 4. Throttle
position
sensor
From fuel tank
Canister
By-pass valve

13A-29MPI – TROUBLESHOOTING, ON-VEHICLE SERVICING
•Example 2
Waveform characteristics
The waveform is displaced to the left or the right.
Cause of the problem
The timing belt is loose
There is an abnormality in the fuel pump camshaft
On-vehicle servicing
1. Adjusting standard engine revolutions
when idling
The standard engine revolutions when idling have been
changed. All other servicing requirements are the same as
before.
Standard engine revolutions when idling: 800 ± 50 r/min
NameCodeNameCode
Intake cam position sensorCOil feeder control valveA
Air temperature sensorBManifold absolute pressure sensorB
Exhaust cam position sensorC
2. Layout diagram for MPI system components
air temp. sensor side
connector
air temp.
sensor
3. Inspection of the air temperature sensor
(1) Disconnect the air temperature sensor connector.
(2) Measure the resistance across the terminals of the air
temperature sensor connector.
Standard values:
13~18 kΩ (when at -20 ºC)
5.1~6.9 kΩ (when at 0 ºC)
2.0~3.0 kΩ (when at 20 ºC)
0.9~1.5 kΩ (when at 40 ºC)
0.40~0.78 kΩ (when at 60 ºC)
0.23~0.42 kΩ (when at 80 ºC)

INTAKE & EXHAUST INTER-COOLER WATER SPRAY
15-3
Fitting guidelines



A 

Fitting the water spray hose ASSY and fixing tape (for securing the water spray hose ASSY)
1. After fitting the water spray hose, the three-way joint and the washer valve, affix pads, clips and tape at the positions
shown in the water spray hose diagram.
2. Fit the water spray hose ASSY to the front bumper using the water spray hose ASSY clip.
3. Affix tape as shown in the diagram, so that the water spray hose ASSY does not slip.
View of the inside of the front bumper
tape
three-way joint
pads
tape
washer
valve
clip
tapeclip
three-way joint
padclip
washer valve
tape
clip
tape
clipclip
water spray hose ASSY
water spray
nozzle brackets
tape

INTAKE & EXHAUST – SECONDARY AIR CONTROL SYSTEM, INLET MANIFOLD15-5
Fitting guidelines



A 
Fitting the gasket
Fit the gasket so that the protruding part points in the direction
shown in the diagram.
Inlet manifold
Removal and fitting
Jobs to be completed before removal and
after fitting
•Take measures to prevent fuel leaking (only
before removal)
•Removal and refitting of the valence (Ref
Section 15: Front bumper)
•Draining and refilling the coolant
•Removal and refitting of the air duct•Removal and refitting of the strut tower bar
•Removal and refitting of the throttle body
•Removal and refitting of the secondary air
control valve (Ref P15-4)
•Removal and refitting of the cross member bar
•Removal and refitting of the front exhaust pipe
protruding
part
(engine oil)
(engine oil)

INTAKE & EXHAUST – EXHAUST MANIFOLD15-10



B 
Fitting the air outlet fitting gasket
Fit the gasket so that the protruding part is in the position located in
the diagram.



C 
Fitting the oil return pipe gasket (oil pan side)
Fit so that the printed side of the gasket is on the oil pan side.



D 

Fitting the oil return pipe gasket (turbocharger side)
Fit so that the printed side of the gasket is on the turbocharger side.turbocharger
protruding part
view “A”
view “A”
print
print
gasket
gasket
3. Apply some fresh engine oil via the fitting hole for the oil feed
pipe in the turbocharger ASSY.