fuel MITSUBISHI LANCER EVOLUTION IX 2005 Workshop Manual

LANCER
EVOLUTION IX
FOREWORD
This manual contains details of the main changes to the
2005 model Lancer Evolution IX. Only differences to the
current Lancer Evolution VIII MR are included, so please use
this manual in conjunction with the related manuals as listed
on the following page.
Please read this manual carefully so that servicing can be
done correctly and quickly, and vehicle performance
maintained.
This manual is based on the current (March 2005) model.
Please bear in mind that vehicle specifications may change
and that future models may not be the same.
Please note that all the units shown in this manual follow the
internationally recognized SI unit system, and that the used
previously are not shown alongside the SI units.
(Nevertheless, please take care because units in reference
documents may be shown in the units which were previously
used). March 2005
MITSUBISHI MOTOR CORPORATION

CONTENTS
General ........................................................
Engine .........................................................
Fuel ..............................................................
Engine Cooling ...........................................
Intake and Exhaust ....................................
Engine Electrical ........................................
Rear axle .....................................................
Wheels and tyres ........................................
Front suspension ...............................................Body
Body.......................................................................
Exterior ........................................................
Interior and SRS Airbag .............................N
Chassis Electrical.........................................
This manual is printed on recycled paper
00
11
13
14
15
16
27
31
33
42
51
52
54
Any opinions, requests or questions concerning this manual,
should be written on the ‘Servicing Comments Form’ at the
end of the manual, and sent to us by fax.

ENGINE – CAMSHAFT, VALVE STEM SEAL, CYLINDER HEAD GASKET11-14



O 
Fitting the O-ring/oil feeder control valve
Caution
1. Do not re-use O-rings.
2. When fitting O-rings, first wind some non-adhesive tape
(seal tape etc) around the oil channel of the oil feeder
control valve, in order to prevent damage to the O-ring.
If the O-ring touches the oil it could start an oil leak.
1. Apply engine oil to the O-ring on the oil feeder control valve.
2. Fit the oil feeder control valve to the cylinder head.
3. Tighten the mounting bolts for the oil feeder control valve to the
specified torque.
Tightening torque: 11 ± 1 N•m
Cylinder head gasket
Removal and fitting
Jobs to be completed before removal and after fitting
•Measures to prevent fuel leaking.
•Check for fuel dripping.
•Removal and refitting of the strut tower bar.
•Removal and refitting of the valence. (Ref Section 51: Front bumper)
•Check the tension of the drive belt.
•Adjustment of the axle letter cable.
•Draining and replacing the engine oil.
•Draining and replacing the coolant.
•Removal and refitting of the air cleaner.
•Removal and refitting of air pipe C.
•Removal and refitting of the battery and the battery tray.
•Removal and refitting of the centre cover. (Ref P11-5)
•Removal and refitting of the axle letter cable.
•Removal and refitting of the radiator.
•Removal and refitting of the front exhaust pipe.
•Removal and refitting of the timing belt. (Ref P11-20)
Tape

ENGINE – CYLINDER HEAD GASKET
11-15
Removal procedure
1. Ignition coil connector
2. O
2sensor connector
3. Oil feeder control valve connector
4. Crank angle sensor connector
5. Manifold absolute pressure sensor
connector
6. Fuel pressure solenoid valve connector
7. Knock sensor connector
8. Purge control solenoid valve connector
9. Throttle position sensor connector
10. Injector connector
11.Exhaust camshaft position sensor
connector12. Inlet camshaft position sensor
connector
13. Water temperature gauge unit
connector
14. Joint control harness and transmission
harness
15. Water temperature sensor connector
16. Secondary air control solenoid valve
connector
17. Vacuum tank, solenoid valve, vacuum
pipe and hose assembly
18. Brake booster vacuum hose connection
19. Oil level gauge and guide assembly
20. O-ring
21. Purge hose connection
(engine oil)

ENGINE – CYLINDER HEAD GASKET11-16
22. Alternator bracket connection
23. Inlet manifold stay
24. Eye bolt
25. Gasket
26. Eye bolt
27. Gasket
28. Oil feeder control valve pipe
29. Filter
30. Oil pipe joint
31. Gasket
32. Oil return pipe gasket
33. Oil return pipe
34. Oil return pipe gasket35. Oil return pipe gasket
36. Exhaust fitting bracket
•Water outlet fitting and thermostat case
assembly (Refer to Section 14: Water hose
pipe)
37. Water hose connection
38. Heater hose connection
39. Fuel return hose connection
40. Fuel high pressure hose connection
41. O-ring
42. Cylinder head bolt
43. Cylinder head assembly
44. Cylinder head gasket
(when
cool)
(engine oil)
(engine oil)



E 




D 




C 



C 
 
A






B 



A 

ENGINE – CYLINDER HEAD GASKET11-18
3. Use the special wrench for cylinder head bolts (MB991654) to
(loosely) tighten the bolts in the following order.
(1) In the order shown in the diagram, tighten the bolts to
78 ± 2 N•m.
(2) In reverse order to that shown in the diagram, completely loosen
the bolts.
(3) In the order shown in the diagram, tighten the bolts to
20 ± 2 N•m.
(4) Make a paint mark on the top of the cylinder head bolt, and on
the cylinder head, and tighten them to 90° as shown in the
diagram.
(5) Tighten the bolts to 90° as shown in the diagram, and check that
the paint mark on the top of the cylinder head bolt and the paint
mark on the cylinder head are in line.
Caution
1) If a bolt is tightened to an angle of less than 90° it has not
been tightened sufficiently.
2) If the angle of tightening exceeds the regulation level,
remove the bolt and start again from procedure number (1).



C 
Fitting the O-ring/fuel high pressure hose
1. Apply a little fresh engine oil to the O-ring.
Caution
Ensure that engine oil does not get inside the delivery pipe.
2. Without damaging the O-ring, twist the fuel high pressure hose
to fit it to the delivery pipe, making sure that it is twisted
smoothly.
3. If the hose cannot be twisted smoothly, there is a possibility that
it may be biting into the O-ring, so remove the fuel high pressure
hose, and check for any damage to the O-ring. If the O-ring is
undamaged, reinsert it into the delivery pipe and check once
more whether the hose can be turned smoothly.
4. Tighten the mounting bolts for the fuel high pressure hose to the
specified torque.
Tightening torque: 5.0 ± 1.0 N•m.
Front of engine
Procedure number (4)Procedure number (5)
paint markpaint mark

ENGINE – TIMING BELT, TIMING BELT B, ENGINE ASSY11-28
5. Using the special wrench for the tensioner pulley socket
(MD998767) or a torque wrench, apply tension torque (3.5 N·m)
to the timing belt in the direction shown in the diagram, and
tighten the mounting bolt for the tensioner pulley to the specified
torque.
Tightening torque: 48 ± 5 N·m
Caution
When tightening the installed bolt, take care that the
tensioner pulley does not turn around with it. If the pulley
does turn around with the bolt, the tension of the belt will
become too strong.
6. Remove the wire or pin which had been inserted when the auto-
tensioner was fitted.
7. Remove by hand the special adjusting bolt (MD998738) which
had been fitted in step 1.
8. Turn the crankshaft two complete turns in a clockwise direction,
and leave it for about 15 minutes.
9. Reinsert the wire or pin which had been removed in step 6, and
check that it can be easily pulled out again.
If the wire or pin can be easily pulled out the tension of the
timing belt is just right, so the wire or pin should be removed
completely. At this point check that the auto-tensioner rod is not
projecting more than the amount specified.
Specified projection (A): 3.8 ~ 4.5 mm
10. If the wire or pin cannot be easily pulled out, repeat steps 1 to 8
until the tension of the timing belt is just right.
11.Recheck that the timing marks on all of the sprockets are in line.
Caution
If the crankshaft bolt is turned in an anti-clockwise
direction, the tightening torque of the crankshaft bolt must
be checked, and if it is loose, it must be retightened.
ENGINE ASSY
Removal and fitting
Jobs to be completed before removal and after fitting
•Measures to prevent fuel leaking.
•Check for fuel dripping.
•Removal and refitting of the bonnet.
•Removal and refitting of the strut tower bar.
•Removal and refitting of the valence. (Ref Section 51: Front bumper)
•Checking the tension of the drive belt.
•Adjustment of the axle letter cable.
•Draining and replacing the engine oil.
•Draining and replacing the coolant.
•Removal and refitting of the air cleaner.
•Removal and refitting of air pipe C.
•Removal and refitting of the battery and the battery tray.
•Removal and refitting of the centre cover. (Ref P11-5)
•Removal and refitting of the axle letter cable.
•Removal and refitting of the radiator.
•Removal and refitting of the front exhaust pipe.

ENGINE – ENGINE ASSY
11-29
Removal procedure
1. Ignition coil connector
2. O
2sensor connector
3. Oil feeder control valve connector
4. Crank angle sensor connector
5. Manifold absolute pressure sensor
connector
6. Fuel pressure solenoid valve connector
7. Knock sensor connector
8. Purge control solenoid valve connector
9. Throttle position connector
10. Injector connector11.Exhaust cam position sensor connector
12. Inlet cam position sensor connector
13. Water temperature gauge unit connector
14. Joint control harness and transmission
harness
15. Water temperature sensor connector
16. Alternator connector and terminal
17. Secondary air control solenoid valve
connector
18. Engine oil pressure switch connector
19. Drive belt
 
A

ENGINE – ENGINE ASSY11-30
Caution
Parts marked * should be temporarily tightened, and then tightened properly when the full weight of the engine is
being supported by the chassis.
20. Vacuum tank, solenoid valve, vacuum
pipe and hose ASSY
21. Brake booster vacuum hose connection
22. Purge hose connection
23. Power steering oil pressure switch
connector
24. Heat protector
25. Power steering oil pump
26. A/C compressor connector

27. A/C compressor A/C>28. Heater hose connection
29. Fuel return hose connection
30. Fuel high pressure hose connection
31. O-ring
•Transfer ASSY, transmission ASSY
32. Engine mount bracket & stopper ASSY
33. Engine ASSY
 
B


 
B






D 



D 
 
C






C 
 
D






B 
 
E






A 
(engine oil)

ENGINE – ENGINE ASSY11-34
 
D


Fitting the O-ring and the fuel high pressure hose
1. Apply a little fresh engine oil to the O-ring.
Caution
Ensure that no engine oil gets inside the deliver pipe.
2. Without damaging the O-ring, fit the fuel high pressure hose to
the delivery pipe by twisting it from left to right. Ensure that the
hose is twisted smoothly.
3. If the hose cannot be twisted smoothly, there is a possibility that
it may be biting into the O-ring, so remove the fuel high pressure
hose, and check for any damage to the O-ring. If the O-ring is
undamaged, reinsert it into the delivery pipe and check once
more whether the hose can be turned smoothly.
4. Tighten the mounting bolts for the fuel high pressure hose, to
the specified torque.
Tightening torque: 5.0 ± 1.0 N•m.

MPI – GENERAL
13A-1
SECTION 13A
MPI (Multi-point Fuel Injection)
CONTENTS
General ..................................................................... 2
Servicing standards .................................................3
Special tools ............................................................3
Troubleshooting ......................................................5Servicing the vehicle ............................................29
1. Adjusting specified revolutions when idling.....29
2. MPI system components layout diagram ........29
3. Checking the air temperature sensor..............29
4. Checking the oil feeder control valve..............30
GENERAL
Servicing guidelines have been changed because of the changes listed below.
•Avariable valve timing control system (V.V.T.) has been adopted. Because of this, an oil feeder control valve and an intake
cam position sensor have been added.
•Amanifold absolute pressure (MAP) sensor has been added.
•An air temperature sensor has been added.