Evo 7 workshop manual MITSUBISHI LANCER EVOLUTION VI 1999 User Guide
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1999, Model line: LANCER EVOLUTION VI, Model: MITSUBISHI LANCER EVOLUTION VI 1999Pages: 558, PDF Size: 9.73 MB
Page 141 of 558
MPI – Troubleshooting13-29
INSPECTION PROCEDURE 12
When the engine is hot, it stalls at idling. (Die out)
Probable cause
In such cases as the above, the cause is probably that ignition system, air/fuel mixture,
idle speed control (ISC) or compression pressure is defective.
In addition, if the engine suddenly stalls, the cause may also be a defective connector
contact.Malfunction of the ignition system
Malfunction of air-fuel ratio control system
Malfunction of the ISC servo system
Drawing air into intake system
Improper connector contact
Backflow of secondary air to the intake system
Were the battery terminals disconnected recently?Ye sAfter warming-up, let the engine run at idling for about 10 minutes.
No
MUT-II Diagnosis code
Are diagnosis codes displayed?Ye sRefer to P.13-8, INSPECTION CHART FOR DIAGNOSIS CODES.
No
Check the ISC servo for operation sound.NGCheck the ISC servo system.
(Refer to P.13-44, INSPECTION PROCEDURE 33.)
OK
Check the injector for operation sound.NGCheck the injector system. (Refer to P.13-15, INSPECTION PRO-
CEDURE FOR DIAGNOSIS CODE 41.)
OK
Does the engine stall right after the accelerator pedal is released?Ye sClean the throttle valve
area.Adjust the fixed SAS.
(Refer to P.13-30.)*
No
Does the engine stall easily again?NoWhile carrying out an intermittent malfunction simulation test (Refer
to GROUP 00 – Points to Note for Intermittent Malfunctions.), check
for sudden changes in the signals shown below.
Crank angle sensor signal
Injector drive signal
Fuel pump drive signal
Air flow sensor signalSecondary ignition signal
Engine-ECU power supply
voltage
Ye s
MUT-II: Engine stalling inspection when the engine is warm and
idling. (Refer to P.13-50, INSPECTION PROCEDURE 42.)
OK
Check the ignition timing.
(Refer to GROUP 11 – ENGINE ADJUSTMENTS.)*NGCheck that the crank angle sensor and the timing belt cover are
installed properly.
OK
Check the following items.
Check the ignition coil, spark plugs, spark plug cables.
Check the secondary air supply system. (Ensure that there is no backflow of secondary air into the intake system.)
Check if the injectors are clogged.
Check the compression pressure.
Check if foreign materials (water, alcohol, etc.) got into fuel.
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).
Page 143 of 558
MPI – Troubleshooting13-31
INSPECTION PROCEDURE 15
Hesitation, sag or stumble
Probable cause
In cases such as the above, the cause is probably that ignition system, air/fuel mixture
or compression pressure is defective.Malfunction of the ignition system
Malfunction of air-fuel ratio control system
Malfunction of the fuel supply system
Poor compression
Malfunction of the turbocharger system
Malfunction of the secondary air supply system
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13-8, INSPECTION CHART FOR DIAGNOSIS CODES.
No
Check the injectors for operation sound.NGCheck the injector system. (Refer to P.13-15, INSPECTION PRO-
CEDURE FOR DIAGNOSIS CODE 41.)
OK
Check the ignition timing.
(Refer to GROUP 11 – Engine Adjustments.)*NGCheck that the crank angle sensor and the timing belt cover are
installed properly.
OK
MUT-II: Check if hesitation, sag, stumble or poor acceleration
occurs. (Refer to P.13-51, INSPECTION PROCEDURE 43.)
OK
Check the fuel pressure. (Refer to P.13-30.)*
OK
Check the following items.
Check the ignition coil, spark plugs, spark plug cables.
Check the turbocharger boost pressure.
Check the boost pressure control system.
Check the turbocharger turbine wheel for smooth rotation.
Check the compression pressure.
Check the fuel filter or fuel line for clogging.
Check the secondary air supply system.
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).
INSPECTION PROCEDURE 16
The feeling of impact or vibration when accelerating
Probable cause
In cases such as the above, the cause is probably that there is an ignition leak
accompanying the increase in the spark plug demand voltage during acceleration.Malfunction of the ignition system
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13-8, INSPECTION CHART FOR DIAGNOSIS CODES.
No
Check the following items.
Check the ignition coil, spark plugs, spark plug cables.
Check for occurrence of ignition leak.
Page 144 of 558
MPI – Troubleshooting13-32
INSPECTION PROCEDURE 17
The feeling of impact or vibration when decelerating
Probable cause
Malfunction of the ISC servo system is suspected.Malfunction of the ISC servo system
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13-8, INSPECTION CHART FOR DIAGNOSIS CODES.
No
Check the ISC servo for operation sound.NGCheck the ISC servo system.
(Refer to P.13-44, INSPECTION PROCEDURE 33.)
OK
MUT-II Data list
14 Throttle position sensor (Refer to P.13-57.)NGCheck the throttle position sensor system. (Refer to P.13-9, IN-
SPECTION PROCEDURE FOR DIAGNOSIS CODE 14.)
OK
MUT-II Data list
26 Idle position switch (Refer to P.13-58.)NGCheck the idle position switch system.
(Refer to P.13-38, INSPECTION PROCEDURE 26.)
OK
Clean the throttle valve area.
INSPECTION PROCEDURE 18
Poor acceleration
Probable cause
Defective ignition system, abnormal air-fuel ratio, poor compression pressure, etc.
are suspected.Malfunction of the ignition system
Malfunction of air-fuel ratio control system
Malfunction of the fuel supply system
Poor compression pressure
Clogged exhaust system
Malfunction of the turbocharger system
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13-8, INSPECTION CHART FOR DIAGNOSIS CODES.
No
Check the injectors for operation sound.NGCheck the injector system. (Refer to P.13-15, INSPECTION PRO-
CEDURE FOR DIAGNOSIS CODE 41.)
OK
Check the ignition timing.
(Refer to GROUP 11 – Engine Adjustments.)*NGCheck that the crank angle sensor and the timing belt cover are
installed properly.
OK
MUT-II: Check if hesitation, sag, stumble or poor acceleration occur.
(Refer to P.13-51, INSPECTION PROCEDURE 43.)
OK
Check the fuel pressure. (Refer to P.13-30.)*
OK
Check the following items.
Check the ignition coil, spark plugs, spark plug cables.
Check the turbocharger boost pressure.
Check the boost pressure control system.
Check the turbocharger turbine wheel for smooth rotation.
Check the compression pressure.
Check the fuel filter or fuel line for clogging.
Broken air intake hose
Clogged air cleaner
Clogged exhaust system
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).
Page 145 of 558
MPI – Troubleshooting13-33
INSPECTION PROCEDURE 19
Surge
Probable cause
Defective ignition system, abnormal air-fuel ratio, etc. are suspected.Malfunction of the ignition system
Malfunction of air-fuel ratio control system
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13-8, INSPECTION CHART FOR DIAGNOSIS CODES.
No
Check the injectors for operation sound.NGCheck the injector system. (Refer to P.13-15, INSPECTION PRO-
CEDURE FOR DIAGNOSIS CODE 41.)
OK
Check the ignition timing.
(Refer to GROUP 11 – Engine Adjustments.)*NGCheck that the crank angle sensor and the timing belt cover are
installed properly.
OK
MUT-II: Check if surge occurs.
(Refer to P.13-52, INSPECTION PROCEDURE 44.)
OK
Check the fuel pressure. (Refer to P.13-30.)*
OK
Check the following items.
Check the ignition coil, spark plugs, spark plug cables.
Check the waste gate actuator.
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).
INSPECTION PROCEDURE 20
Knocking
Probable cause
In cases as the above, the cause is probably that the detonation control is defective
or the heat value of the spark plug is inappropriate.Defective detonation sensor
Inappropriate heat value of the spark plug
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13-8, INSPECTION CHART FOR DIAGNOSIS CODES.
No
Does knocking occur when driving with the sensor disconnected?
At this time, use the MUT-II to check if the timing is retarded
compared to when the detonation sensor connector is con-
nected.NoCheck the detonation sensor system. (Refer to P.13-15, INSPEC-
TION PROCEDURE FOR DIAGNOSIS CODE 31.)
Ye s
Check the following items.
Spark plugs
Check if foreign materials (water, alcohol, etc.) got into fuel.
INSPECTION PROCEDURE 21
Dieseling
Probable cause
Fuel leakage from injectors is suspected.Fuel leakage from injectors
Check the injectors for fuel leakage.
Page 146 of 558
MPI – Troubleshooting13-34
INSPECTION PROCEDURE 22
Too high CO and HC concentration when idling
Probable cause
Abnormal air-fuel ratio is suspected.Malfunction of the air-fuel ratio control system
Deteriorated catalyst
Check trouble symptom.
No
Check the ignition timing.
(Refer to GROUP 11 – Engine Adjustments.)*NGCheck that the crank angle sensor and the timing belt cover are
installed properly.
OK
MUT-II Data list
21 Engine coolant temperature sensor. (Refer to P.13-57.)NGCheck the engine coolant temperature sensor system.
(Refer to P.13-10, INSPECTION PROCEDURE FOR DIAGNOSIS
CODE 21.)
OK
MUT-II Data list
13 Intake air temperature sensor (Refer to P.13-56.)NGCheck the intake air temperature sensor system. (Refer to P.13-9,
INSPECTION PROCEDURE FOR DIAGNOSIS CODE 13.)
OK
MUT-II Data list
25 Barometric pressure sensor (Refer to P.13-58.)NGCheck the barometric pressure sensor system. (Refer to P.13-14,
INSPECTION PROCEDURE FOR DIAGNOSIS CODE 25.)
OK
MUT-II Data list
11 Oxygen sensor
OK:600–1,000 mV when racing suddenlyNGCheck the oxygen sensor system. (Refer to P.13-15, INSPECTION
PROCEDURE FOR DIAGNOSIS CODE 31.)
OK
MUT-II Data list
11 Oxygen sensor
OK:Repeat 0–400 mV and 600–1,000 mV alternately when
idling.OK
NG
Check the fuel pressure. (Refer to P.13-30.)*
OK
NG
Check the following items.
Check the injectors for operation sound.
Check the injectors for fuel leakage.
Check the ignition coil, spark plugs, spark plug cables.
Check the compression pressure.
Check the positive crankcase ventilation system.
Check the evaporative emission control system.
Check the trouble symptom.
NG
Replace the catalytic converter.
Replace the oxygen sensor.
MUT-II Self-Diag code
Are diagnosis codes displayed?Ye sRefer to P.13-8, INSPECTION CHART FOR DIAGNOSIS CODES.
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).
Page 148 of 558
MPI – Troubleshooting13-36
INSPECTION PROCEDURE 25
Fuel pump system
Probable cause
The engine-ECU turns the control relay ON when the engine is cranking or running,
and this supplies power to drive the fuel pump.Malfunction of the fuel pump relay
Malfunction of the fuel pump
Improper connector contact, open or short-circuited
harness wire
Malfunction of the engine-ECU
OK
Check the harness wire between resistor connector and fuel pump
drive terminal and between fuel pump relay No.2 connector and
fuel pump drive terminal, and repair if necessary.
OK
Check the resistor. (Refer to P.13-34.)*NG
Replace
OK
Measure at the resistor connector A-124.
Disconnect the connector.
Voltage between 1 and earth
MUT-II Actuator test: Fuel pump relay No.2 drive
OK:System voltageNGCheck the harness wire between fuel pump relay No.2 and resistor
connector, and repair if necessary.
OK
Measure at the engine-ECU connector B-60.
Connect the connector.
Voltage between 39 and earth
MUT-II Actuator test: Fuel pump drive
OK:System voltageNGCheck the harness wire between fuel pump relay No.2 and
engine-ECU connector, and repair if necessary. NG
Check the harness wire between fuel pump relay and fuel pump
relay No.2 connector, and repair if necessary.
OK
Measure at the fuel pump relay No.2 connector A-123.
Disconnect the connector.
Voltage between each of 3 and 5 and earth
MUT-II Actuator test: Fuel pump drive
OK:System voltage
OK
Check the fuel pump relay No.2. (Refer to P.13-68)NG
Replace
OK
Check the following connectors:
D-18, D-04, B-64, A-124, A-123, B-59, B-60NG
Repair
OK
Measure at the fuel pump relay connector B-28.
Connect the connector.
Voltage between 1 and earth
MUT-II Actuator test: Fuel pump drive
OK:System voltageNGCheck the fuel pump drive control circuit.
(Refer to P.13-54, INSPECTION PROCEDURE 47.)
OK
Check the fuel pump relay. (Refer to P.13-68.)NG
Replace
Check the fuel pump operation by applying the system voltage
to the fuel pump drive terminal.NGCheck the fuel pump circuit.
(Refer to P.13-53, INSPECTION PROCEDURE 46.)
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).
Page 150 of 558
MPI – Troubleshooting13-38
INSPECTION PROCEDURE 26
Idle position switch system
Probable cause
The idle position switch inputs the condition of the accelerator pedal, i.e. whether
it is depressed or released (HIGH/LOW), to the engine-ECU.
The engine-ECU controls the idle speed control servo based on this input.Maladjustment of the accelerator cable
Maladjustment of the fixed SAS
Maladjustment of the idle position switch and throttle
position sensor
Improper connector contact, open or short-circuited
harness wire
Malfunction of the engine-ECU
Check the idle position switch. (Refer to P.13-30.)*NGReplace the throttle position sensor.
OK
Measure at the throttle position sensor connector A-16.
Disconnect the connector, and measure at the harness side.
Voltage between 3 and earth (Ignition switch: ON)
OK:4 V or higher
Continuity between 4 and earth
OK:ContinuityNGCheck the following
connector: B-62NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire between engine-ECU and throttle position
sensor connector.
OK
Replace the engine-ECU.
NG
Repair
OK
Check the following
connector: A-16NG
Repair
OK
Check trouble symptom.
NG
Replace the engine-ECU.
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).
INSPECTION PROCEDURE 27
Ignition switch-ST system
Probable cause
The ignition switch-ST inputs a HIGH signal to the engine-ECU while the engine is
cranking.
The engine-ECU controls fuel injection, etc. during starting based on this input.Malfunction of ignition switch
Improper connector contact, open or short-circuited
harness wire
Malfunction of the engine-ECU
Measure at the engine-ECU connector B-62.
Disconnect the connector, and measure at the harness side.
1. Voltage between 71 and earth (Ignition switch: START)
OK:8V
2. Continuity between 91 and earth
OK:Continuity1. NGCheck the following
connector: B-64NG
Repair
OK
Check trouble symptom.
NG
Check harness wire be-
tween the engine-ECU
and ignition switch con-
nector.NG
Repair
OK
Check the ignition switch.
2. NG
Check the harness wire between engine-ECU connector (terminal
No.91) and earth, and repair if necessary.
OK
Check the following
connector: B-62NG
Repair
OK
Check trouble symptom.
NG
Replace the engine-ECU.
Page 154 of 558
MPI – Troubleshooting13-42
INSPECTION PROCEDURE 31
Oxygen sensor system
Probable cause
When CO or HC concentration is too high, the malfunction of the parts shown at
right may be the cause.
The oxygen sensor detects the density of oxygen in exhaust gas and inputs it
to the engine-ECU after converting into a voltage signal.
The engine-ECU controls the fuel injection amount based on this signal such that
the stoichiometric air/fuel mixture ratio can be obtained.Malfunction of oxygen sensor
Improper connector contact, open or short-circuited
harness wire
Malfunction of engine-ECU
OK
Replace the engine-ECU.
Check the harness wire between
engine-ECU and oxygen sensor connector.NG
Repair
NG
OK
Check trouble symptom.
OK
Replace the engine-ECU.
NG
Check the harness wire between
engine-ECU and oxygen sensor connector.NG
Repair
OK
Check trouble symptom.
OK
Check the following connector: A-63NG
Repair
OK
Measure at the oxygen sensor connector A-63.
Disconnect the connector, and measure at the harness side.
Continuity between 2 and earth
OK:ContinuityNGCheck the following connector: B-62NG
Repair
Check the oxygen sensor. (Refer to P.13-32.)*NG
Replace
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).
Page 155 of 558
MPI – Troubleshooting13-43
INSPECTION PROCEDURE 31
Oxygen sensor system
Probable cause
When CO or HC concentration is too high, the malfunction of the parts shown at
right may be the cause.
The oxygen sensor detects the density of oxygen in exhaust gas and inputs it
to the engine-ECU after converting into a voltage signal.
The engine-ECU controls the fuel injection amount based on this signal such that
the stoichiometric air/fuel mixture ratio can be obtained.Malfunction of oxygen sensor
Improper connector contact, open or short-circuited
harness wire
Malfunction of engine-ECU
OK
Replace the engine-ECU.
NG
Check the harness wire between oxygen sensor, engine-ECU,
and repair if necessary.
OK
Check trouble symptom.
NG
Check the harness wire between oxygen sensor and engine-ECU,
and repair if necessary.
OK
Check trouble symptom.
OK
Check trouble symptom.NGCheck the harness wire between
engine-ECU and oxygen sensor.NG
Repair
OK
Check the following connector: B-61NG
Repair
OK
NG
Measure at the engine-ECU connector B-61.
Disconnect the connector, and measure at the harness side.
Voltage between 60 and earth
(Ignition switch: ON)
OK:System voltageCheck the following connector: A-63NG
Repair 1. NG
Check the harness wire between oxygen sensor and control relay,
and repair if necessary.
OK
2. NG
Measure at the oxygen sensor connector A-63.
Disconnect the connector, and measure at the harness side.
1. Voltage between 1 and earth
(Ignition switch: ON)
OK:System voltage
2. Continuity between 2 and earth
OK:Continuity
Check the following connector: B-62NG
Repair
Check the oxygen sensor. (Refer to P.13-32)*NG
Replace
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).
Page 157 of 558
MPI – Troubleshooting13-45
INSPECTION PROCEDURE 34
Fuel pressure control valve system
Probable cause
The fuel pressure control valve switches the pressure introduction into the fuel pressure
regulator between the intake manifold and atmosphere.Malfunction of solenoid valve
Improper connector contact, open or short-circuited
harness wire
Malfunction of engine-ECU
NGReplace the engine-ECU.
OK
Check trouble symptom.
NG
Check the harness wire between engine-ECU and solenoid valve
connector, and repair if necessary.
OK
Check trouble symptom.
OK
Check the following connector: B-59NG
Repair
OK
Measure at the engine-ECU connector B-59.
Disconnect the connector, and measure at the harness side.
Voltage between 3 and earth
(Ignition switch: ON)
OK:System voltageNGCheck the following connector: A-12NG
Repair NG
Check the harness wire between control relay and solenoid valve
connector, and repair if necessary.
OK
Measure at the fuel pressure control valve connector A-12.
Disconnect the connector, and measure at the harness side.
Voltage between 1 and earth
(Ignition switch: ON)
OK:System voltage
Check the fuel pressure control valve.NG
Replace
INSPECTION PROCEDURE 35
Waste gate solenoid valve
Probable cause
The waste gate solenoid valve controls the boost pressure introduced into the waste
gate actuator in the turbocharger.Malfunction of solenoid valve
Improper connector contact, open or short-circuited
harness wire
Malfunction of engine-ECU
NGReplace the engine-ECU.
OK
Check trouble symptom.
NG
Check the harness wire between engine-ECU and solenoid valve
connector, and repair if necessary.
OK
Check trouble symptom.
OK
Check the following connector: B-59NG
Repair
OK
Measure at the engine-ECU connector B-59.
Disconnect the connector, and measure at the harness side.
Voltage between 11 and earth
(Ignition switch: ON)
OK:System voltageNGCheck the following connector: A-23NG
Repair NG
Check the harness wire between control relay and solenoid valve
connector, and repair if necessary.
OK
Measure at the waste gate solenoid valve connector A-23.
Disconnect the connector, and measure at the harness side.
Voltage between 2 and earth
(Ignition switch: ON)
OK:System voltage
Check the waste gate solenoid valve.
(Refer to Group 15 – On-vehicle service.)*NG
Replace
NOTE
*: Refer to Workshop Manual for LANCER EVOLUTION-IV and EVOLUTION-V (Pub. No. S9806CNCP9).