keyless MITSUBISHI LANCER EVOLUTION VI 1999 Workshop Manual

42-1
BODY
CONTENTS
GENERAL 2. . . . . . . . . . . . . . . . . . . . . . . . . .
OUTLINE OF CHANGE 2. . . . . . . . . . . . . . . . . .
KEYLESS ENTRY SYSTEM 2. . . . . . . . . .
SPECIAL TOOL 2. . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 2. . . . . . . . . . . . . . . . . . . .
KEYLESS ENTRY SYSTEM 7. . . . . . . . . . . . . .
TRANSMITTER 7. . . . . . . . . . . . . . . . . . . . . . . . . .
SUNROOF 9. . . . . . . . . . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS 9. . . . . . . . . . . . . .
SEALANT 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 9. . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE 13. . . . . . . . . . . . . . . .
Water Test 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sunroof Fit Adjustment 13. . . . . . . . . . . . . . . . . . .
SUNROOF 14. . . . . . . . . . . . . . . . . . . . . . . . . . . .

BODY – General / Keyless Entry System42-2
GENERAL
OUTLINE OF CHANGE

The descriptions of the troubleshooting using on MUT-II tester have been incorporated.
KEYLESS ENTRY SYSTEM
SPECIAL TOOL
ToolNumberNameUse
MB991502MUT-II sub assemblyRecording secret codes
TROUBLESHOOTING
INSPECTION CHART FOR TROUBLE SYMPTOMS
Trouble symptomInspection procedure No.Reference page
None of the doors can be locked or unlocked using the transmitter.142-2
All of the doors can be locked and unlocked using the transmitter,
but the room lamp does not flash or illuminate. (However, the room
lamp operates normally when the doors are opened and closed.)242-4
Secret codes cannot be registered.342-4
INSPECTION PROCEDURE FOR TROUBLE SYMPTOMS
INSPECTION PROCEDURE 1
None of the doors can be locked or unlocked using the
transmitter.
Probable cause
The cause may be a malfunction of the transmitter, a malfunction of the receiver
or the lock and unlock signals are not being input to the ETACS-ECU.
Malfunction of transmitter

Malfunction of receiver

Malfunction of ETACS-ECU

Malfunction of wiring harness or connector

Malfunction of key reminder switch

Malfunction of door switch
NG
To next page
OK
Replace the transmitter battery. (Refer to P.42-7.)
Ye s
Has the secret code been registered properly? *NGRe-register the secret code. (Refer to P.42-8.)
Can the doors be locked and unlocked by the driver’s-side door
key cylinder and lock knob?NoCheck the centre door lock system.
NOTE
*: This should be done if a transmitter or receiver has been replaced, and if a secret code has not
been registered properly.

BODY – Keyless Entry System42-3
NG
Repair
NG
Check the harness wire, and repair if necessary.

Between receiver and earth
NG
Repair
OK
Replace the ETACS-
ECU.
NG
Repair
OK
Replace the transmitter.NGReplace the receiver.
NG
Check the harness wire.

Between key reminder switch and receiver

Between key reminder switch and earthNG
Repair
OK
Check trouble symptoms.
OK
Check the following connectors:
B-50, B-84, D-01NG
Repair
OK
Key reminder switch continuity check (Refer to GROUP 54 – Ignition
Switch.)NG
Replace
NG
Check the harness wire.

Between receiver and door switchNG
Repair
OK
Check trouble symptoms.
OK
Check the following connectors:
D-01, D-03, D-06, D-17, F-12, F-26NG
Repair
NG
Check the harness wire.

Between ETACS-ECU and receiver
OK
Door switch continuity checkNG
Replace
OK
Check trouble symptoms.
OK
Measure at the receiver connector D-01.

Disconnect the connector, and measure at harness side.

Voltage between 12 and body earth

Voltage between 14 and body earth
OK:System voltageNGCheck the connectors:
B-77, D-01
OK
Check trouble symptoms.
OK
Measure at the receiver connector D-01.

Disconnect the connector, and measure at the harness side.

Continuity between 20 and body earth
OK:ContinuityNGCheck the following connectors:
B-50, D-01
NG
Repair
NG
Check the harness wire, and repair if necessary.

Between ignition switch and receiver

Between fusible link No.1 and receiver
OK
Check trouble symptoms.
Measure at the receiver connector D-01.

Disconnect the connector, and measure at the harness side.

Voltage between 9 and body earth

Voltage between 10 and body earth
OK:System voltageNGCheck the following connectors:
B-49, B-73, B-75, B-76
From previous page

BODY – Keyless Entry System42-4
INSPECTION PROCEDURE 2
All of the doors can be locked and unlocked using the
transmitter, but the room lamp does not flash or
illuminate. (However, the room lamp operates normally
when the doors are opened and closed.)
Probable cause
If the room lamp operates normally when the doors are opened and closed, the cause
of the problem may be a malfunction of the receiver or a malfunction of the harness
between the room lamp the receiver.
Malfunction of receiver

Malfunction of connector or wiring harness
NG
Repair
NG
Check the harness wire between room lamp and receiver, and
repair if necessary.
OK
Replace the receiver.
OK
Check trouble symptoms.
Measure at the receiver connector D-01.

Disconnect the connector, and measure at the harness side.

Voltage between 11 and body earth
OK:System voltageNGCheck the following connectors:
B-80, D-01
INSPECTION PROCEDURE 3
Secret codes cannot be registered.
Probable cause
The cause may be a malfunction of the diagnosis connector, a malfunction of the
power supply or earth circuit of the receiver, a malfunction of the earth circuit or
a malfunction of the diagnosis output circuit.
Malfunction of receiver

Malfunction of MUT-II

Malfunction of connector or wiring harness
NG
Repair
NG
Check the harness wire, and repair if necessary.

Between receiver and diagnosis connector
NG
Repair
NG
Check the harness wire, and repair if necessary.

Between fusible link No.1 and diagnosis connector
OK
Check trouble symptoms.NGCheck the harness wire, and repair if necessary.

Between diagnosis connector and earth
Ye s
To next page
NG
Check the following
connectors:
B-22, B-50NG
Repair
OK
Measure at the diagnosis
connector B-22.

Continuity between 4
and body earth

Continuity between 5
and body earth
OK:ContinuityOKReplace MUT-II.
OK
Check trouble symptoms.
No
Measure at the diagnosis
connector B-22

Voltage between 16
and body earth
OK:System voltageNGCheck the following connectors:
B-22, B-49, B-75
OK
Can the MUT-II communicate with other systems?
OK
Check trouble symptoms.
Measure at the diagnosis connector B-22 and the receiver connector
D-01.

Disconnect the connector, and measure at harness side.

Continuity between following terminals:
OK:Continuity
7 – 1 NGCheck the following connectors:
B-22, D-01

BODY – Keyless Entry System42-5
NG
Repair
NG
Check the harness wire, and repair if necessary.

Between fusible link No.1 and receiver

Between ignition switch and receiver
NG
Repair
NG
Check the harness wire, and repair if necessary.

Between receiver and earth
OK
Replace the receiver.
OK
Check trouble symptoms.
OK
Measure at the receiver connector D-01.

Disconnect the connector, and measure at the harness side.

Between 20 and body earth
OK:ContinuityNGCheck the following connectors:
B-50, D-01
OK
Check trouble symptoms.
Measure at the receiver connector D-01.

Disconnect the connector, and measure at the harness side.

Voltage between 9 and body earth

Voltage between 10 and body earth
OK:System voltageNGCheck the following connectors:
B-49, B-75, D-01
From previous page
INSPECTION OF RECEIVER TERMINAL VOLTAGE
TerminalSignal nameConditionsTerminal voltage
2Door switchOne or more doors are open (Door switch: ON)0 V
All doors are closed (Door switch: OFF)System voltage
6Door lock actuator
switch (driver’s side)
LOCK5 V and pulse output*
switch (driver’s side)
UNLOCK0 V
7Diagnosis changeover
input
When MUT-II is connected0 V
input
When MUT-II is disconnectedSystem voltage
8Key reminder switchOFF (When ignition key is inserted)5 V and pulse output*
ON (When ignition key is removed)0 V
9Ignition switchIgnition switch: ACC or ONSystem voltage
Ignition switch: OFF0 V
10Receiver power supplyAt all timesSystem voltage
11Room lamp outputOne or more door are open (Door switch: ON)0 V
All doors are closed (Door switch: OFF)System voltage

BODY – Keyless Entry System42-6
TerminalSignal nameConditionsTerminal voltage
12Door lock outputWhen activated0 V
When not activatedSystem voltage
14Door unlock outputWhen activated0 V
When not activatedSystem voltage
20EarthAt all times0 V
NOTE
Values marked with * should be measured using an oscilloscope. (The value will alternate between 0
V and 0.03 V if a circuit tester is used.)

BODY – Keyless Entry System42-7
KEYLESS ENTRY SYSTEM
REMOVAL AND INSTALLATION
1
2
Keyless entry receiver removal
steps

Front seat assembly (driver’s side)
1. Keyless entry receiverETACS-ECU removal
2. ETACS-ECU
TRANSMITTER
DISASSEMBLY AND REASSEMBLY
Post-assembly Operation

Transmitter operation check
1
2
34
Disassembly steps
1. Screw
2. TapeA3. Battery
4. Master key assembly

BODY – Keyless Entry System42-8
ASSEMBLY SERVICE POINTS
ABATTERY INSTALLATION
Install a new battery with (+) side upward.
Battery required for replacement:
Lithium battery CR1216
SECRET CODE REGISTRATION METHOD
Each individual secret code is registered inside
the transmitter, and so it is necessary to register
these codes with the EEPROM inside the receiver
in the following cases.

When either the transmitter or receiver is
replaced;

If it appears that a problem is occurring because
of faulty registration of a code.
A maximum of two different codes can be stored
in the memory area of the EEPROM (two different
transmitters can be used). When the code for the
first transmitter is registered, the previously-regis-
tered codes for two transmitters are cleared.
Therefore, if you are using two transmitters or are
adding a second transmitter, the codes for both
transmitters must be registered at the same time.
Before beginning with the registration, check that
the doors lock normally when the key is used.
1. Connect the MUT-II to the diagnosis connector.
NOTE
This will connect terminal (1) of the diagnosis
connector to earth, and the system will be in
secret code registration standby mode.
Caution
Always turn the ignition switch to OFF before
connecting and disconnecting the MUT-II.
2. Close all the doors.
3. Turn the ignition switch to ACC and then back
to OFF.NOTE
The doors will lock and unlock once at this
time and the system will switch to registration
mode.
4. Press the transmitter switch, and then press
it two times within 10 seconds of the first press.
This will register the code.
5. After registration is completed, the doors will
be automatically locked and unlocked once.
6. If you are using two transmitters or have added
a second transmitter, the same registration
procedure should be carried out for the second
transmitter, and it should be carried out within
one minute after registration of the code for
the first transmitter has been completed. After
the second registration is completed, the doors
will be automatically locked and unlocked once.
7. Registration mode will be cancelled if one of
the following conditions is met.

When the secret codes for two transmitters
have been registered;

When 1 minute has passed after
registration mode started;

If the MUT-II is disconnected (the earth
connection is broken);

If the ignition switch is turned to ON;

If any of the doors are opened;
8. After registration is completed, carry out the
following to check if the keyless entry system
is operable properly.

Remove the ignition key.

Close all the doors.

C-2
STOP LAMP 51. . . . . . . . . . . . . . . . . . . . . . . . . .
BACK-UP LAMP 52. . . . . . . . . . . . . . . . . . . . . . .
METER AND GAUGE 54. . . . . . . . . . . . . . . . . .
FUEL WARNING LAMP 56. . . . . . . . . . . . . . . .
BRAKE WARNING LAMP 56. . . . . . . . . . . . . .
OIL PRESSURE WARNING LAMP 57. . . . . .
SEAT BELT WARNING LAMP 57. . . . . . . . . .
CENTRAL DOOR LOCKING SYSTEM 58. .
Without Keyless Entry System 58. . . . . . . . . . . .
With Keyless Entry System 60. . . . . . . . . . . . . . .
HEATER AND AIR CONDITIONER 64. . . . . .
FULL-AUTO AIR CONDITIONER 70. . . . . . . .
WINDSHIELD WIPER AND WASHER 78. .
With Intermittent Wiper 78. . . . . . . . . . . . . . . . . . .
REAR WIPER AND WASHER 79. . . . . . . . . .
DEFOGGER AND DOOR MIRROR
HEATER 80. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Without Full-Auto Air Conditioner 80. . . . . . . . . .
With Full-Auto Air Conditioner 82. . . . . . . . . . . . .
RADIO 84. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Spare Circuit 84. . . . . . . . . . . . . . . . . . . . . .
4 Speaker, 6 Speaker 86. . . . . . . . . . . . . . . . . . . .
KEY REMINDER BUZZER 89. . . . . . . . . . . . . .
ANTI-SKID BRAKING SYSTEM (ABS) 90. .
SUPPLEMENTAL RESTRAINT SYSTEM
(SRS) 96. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACTIVE YAW CONTROL SYSTEM (AYC) 98
INTERCOOLER AND RADIATOR WATER
SPRAY SYSTEM 104. . . . . . . . . . . . . . . . . . . . .

– Dash Panel WIRING HARNESS
CONFIGURATION DIAGRAMS
Connector
symbol
B
C-10
DASH PANEL
B-38 (2) Sunlight sensor automatic air conditioner>
B-39 (6) Air mix damper motor and potentiometer
tioner>
B-40 (3) Automatic compressor ECU

B-41 (8) A/C switch

B-42 (2) Blower switch illumination lamp with heater or manual air conditioner>
B-43 (6-B) Defogger switch manual air conditioner>B-44 (6) Body harness and roof harness combina-
tion
B-45 (2-B) Diode (for keyless entry system circuit)
B-46 (2) Spare connector for fog lamp switch

B-48 (14) J/C (2)
B-49 (14) J/C (3)
B-50 (14-L) J/C (4)
B-51 (21-Y) SRS-ECU
B-52 (16-B) Control harness and body harness
combination