transmission MITSUBISHI LANCER EVOLUTION VIII 2004 Owner's Guide

MANUAL TRANSMISSION TROUBLESHOOTING2220
The ACD mode injector lamp does not come on when the ignition
switch is ON (engine stopped)Assumed cause of concern
ACD mode indicator lamp circuit or 4WDECU malfunctions are possible.• Harness, connector malfunction
• ACD mode indicator lamp ASSY malfunction
• 4WDECU malfunction
Measurement at C106, combi. meter connector.
• Undo connector, take measurement on harness side
• Ignition switch ON
OK:battery voltage
Measurement at C37 4WDECU connector
• Undo connector, take measurement on harness side
• Ignition switch ON
• Earth 40, 51, 52 to body earth
OK:indicator lamp on
Connector check:C37
NG > repair
Fault confirmation Replace 4WDECU
Connector check:C106, C212, C210
NG > repair
Fault confirmation
Check harness between ignition switch – ACD mode
indicator lamp ASSY
• Check power supply wire to see if broken or
damaged
•NG > repair
Check ACD mode indicator lamp ASSY
NG > replace
Connector check:C37, C133, C106
NG > repair
Fault confirmation
Check harness between ACD mode indicator lamp
ASSY 4WDECU
• Check output wire to see if broken or damaged
When C37 4WDECU connector is undone, do all
ACD mode indicator lamps all go out?
Replace 4WDECU
Check connector:C37, C133, C106
NG > repair
Fault confirmation Check harness between ACD mode indicator ASSY
4WDECU
• Check output wire for earthing, shorting
NG > repair
Replace ACD mode indicator ASSY
Checking procedure 3
Checking procedure 4
Even after engine starts, at least 2 ACD mode indicator lamps
remain litAssumed cause of concern
ACD mode indicator lamp output circuit malfunction is possible.•Harness, connector malfunction
• 4WDECU malfunction
• ACD mode indicator lamp ASSY malfunction
Remarks
This phenomenon is limited to when communication with MUTII/III is possible (4WDECU power supply normal), and diagnosis
code is normal/correct.
OK
NG
NG
NO
OK
OK
NG
NG
OK
OK
OK
NG
YESOK
NG
OK

Related documentation
Cautionary Note regarding servicing of vehicles fitted with SRS airbags and/or seatbelts with
pre-tensioner systems.
Warnings:
1. Incorrect inspection or servicing of a component part of the SRS airbag system or seatbelt pre-tensioner system, or
a part relating to these systems, may cause accidental operation (deployment) of the SRS airbag or seatbelt pre-
tensioners, or may cause these systems to be disabled, leading in either case the risk of serious injury.
2. If parts may be affected by heat during painting operations, then those parts must be removed in advance. This
applies to the SRS-ECU, airbag modules (driver’s sear and front passenger’s seat), clock springs, front impact
sensors, side impact sensors, and pre-tensioner seatbelts.
• 93ºC or above : SRS-ECU, airbag modules (driver’s sear and front passenger’s seat), clock springs, front impact
sensors, side impact sensors
• 90ºC or above : Pre-tensioner seatbelts
3. The component parts of the SRS airbag system or seatbelt pre-tensioner system, and parts relating to these
systems, must always be inspected and serviced by a Mitsubishi dealer.
4. Service personnel must read the relevant service manuals (particularly, Section 52B – SRS Airbags) carefully and
thoroughly, before inspecting or servicing the component parts of the SRS airbag system or seatbelt pre-tensioner
system, and parts relating to these systems.
Title of Document No. Date of
IssueTitle of Document No. Date of
Issue
Body Manuals (Service Manual)
• Mirage, Lancer (supplement)
• Lancer Cedia
• Lancer Cedia (supplement)
• Lancer Evolution VII
(supplement)
• Lancer Cedia (supplement)
• Lancer (supplement)
• Lancer Evolution VIII MR
(supplement)1036F52
1036K50
1036K51
1036K52
1036K53
1036K54
1036K55Aug 1996
May 2000
July 2000
May 2001
Oct 2001
Feb 2003
Feb 2004
Electrical Wiring Diagrams
Service Manual
• Lancer Evolution VIII 1036K77 Jan 2003
New Vehicle Manuals
• Mirage, Lancer
• Mirage, Lancer
• Mirage, Lancer
• Mirage, Lancer
• Mirage
• Mirage, Lancer
• Lancer
• Lancer
• Lancer Cedia
• Lancer Cedia
• Lancer Evolution VII
• Lancer Cedia
• Lancer Cedia
• Lancer Evolution VII
• Lancer Cedia
• Lancer Evolution VIII
• Lancer
• Lancer
• Lancer Evolution VIII MR1036F30
1036F31
1036F32
1036F33
1036F34
1036F35
1036F36
1036F37
1036K30
1036K31
1036K32
1036K33
1036K34
1036K35
1036K36
1036K37
1036K38
1036K39
1036K40Oct 1995
Jan 1996
Aug 1996
Jul 1997
Jan 1998
Oct 1998
Jan 1999
Dec 1999
May 2000
July 2000
Jan 2001
May 2001
Oct 2001
Jan 2002
May 2002
Jan 2003
Feb 2003
Dec 2003
Feb 2004Engine Service Manual
• 4G6 Engine
• 4G6 Engine (supplement)1039G46
1039G63Jan 2001
Jan 2003
Service Manuals
• Lancer Cedia
• Lancer Cedia (supplement)
• Lancer Evolution VII
(supplement)
• Lancer Cedia (supplement)
• Lancer Cedia (supplement)
• Lancer Evolution VII
(supplement)
• Lancer Cedia (supplement)
• Lancer Evolution VIII
(supplement)
• Lancer (supplement)
• Lancer (supplement)
• Lancer Evolution VIII MR
(supplement)1036K00
1036K01
1036K02
1036K03
1036K04
1036K05
1036K06
1036K07
1036K08
1036K09
1036K10May 2000
July 2000
Jan 2001
May 2001
Oct 2001
Jan 2002
May 2002
Jan 2003
Feb 2003
Dec 2003
Feb 2004Transmission Service Manual
• W5M51 Manual Transmission
• W5M51 Manual Transmission
(supplement)
• W6MAA Manual Transmission1039M17
1039M22
1039M23Jan 2001
Jan 2003
Jan 2003

GENERAL INFORMATION - VEHICLE IDENTIFICATION0-2
Model
codeClass
code2004
codeGrade Engine model Transmission
modelFuel
supply
system
GH-CT9A SNDFZ!
RS W5M51
(4WD, 5M/T)
SJDFZ!
RS
SJGFZ!
GSR4G63 (2000
DOHC 16-valve
intercooler turbo)
W6MAA
(4WD, 6M/T)MPI
Connector
CodeName Page Details of Change
BEngine transmission p.1-2• Due to changes in the engine control system, the
name of the wastegate solenoid valve (B-30) has
been changed to “wastegate solenoid valve 1”, and
an additional wastegate solenoid valve 2 (B-32) has
been added.
• The 4WD-ECU (C-37, 38) has been moved from
the instrument panel harness to the control harness.
• With the removal of the DVD-MMCS, the following
connectors have been removed.

• Multi-centre display (C-11, 12)

• Navigation unit (C-47)
The immobiliser ECU (C-54) has also been removed,
due to changes in the engine immobiliser system.
CInstrument panel p.1-4
• With the removal of the DVD-MMCS, the following
connectors have been removed.

• Audio unit (C-102)

• Hazard switch (C-105)
FBoot interior p.1-6• Spare connector (F-28) added.
Changed part Page Details of change
ECU p.2-2• With changes in the engine immobiliser system, the
installation position of the immobiliser ECU has been
changed.
Solenoid valve p.2-2• With the addition of the wastegate solenoid valve 2, a
new installation point has been provided.
VEHICLE IDENTIFICATION
M3000000100845
Note:


denotes a continued model
IMPLEMENTATION CODE
M3000001000584
GH-CT9A ; CT9A-0300001 ~
DETAILS OF CHANGES
Wiring diagrams
M3000003000159
Component installation positions
M3000004000141

1-1
SECTION 1
WIRING DIAGRAMS
CONTENTS
Engine transmission ..............................1-2 Instrument panel .....................................1-4
Boot interior ............................................1-6

WIRING DIAGRAMS - ENGINE TRANSMISSION1-2
ENGINE TRANSMISSION
M3010000400494
B-01 (1-black) Engine oil pressure switch
B-02 (1) Alternator
B-03 (4-grey) Alternator
B-04 (1) Starter
B-05 (1-black) Starter
B-06 (4-black) Throttle position sensorB-07 (2-black) Purge control solenoid valve
B-08 (7-black) Airflow sensor
B-12 (5-grey) Windscreen wiper motor
B-13X (1) Engine speed detection connector
B-14X (5) Starter relay
B-17X (4) Ignition coil relay
Connector
symbol -
B
-01
∫
-32
AC311230AB
Control harness
Battery harness

WIRING DIAGRAMS - ENGINE TRANSMISSION1-3
B-19X (4) Engine control relay
B-20X (4) A/C compressor relay
B-21 (10-black) Junction between control harness and
battery harness
B-25 (4-black) O
2sensor
B-26 (2-black) Indicator 4
B-27 (2-black) Indicator 3
B-28 (2-black) Indicator 2
B-29 (2-black) Indicator 1(2-grey) Wastegate solenoid valve 1
B-31 (6-black) Junction between control harness and
transmission harness
(2-grey) Wastegate solenoid valve 2
Note : Boxed connector numbers indicate
connectors with changed names, or new,
additional connectors.
B-32
B-32
Earth cable
Transmission harness
AC311231AB