check oil MITSUBISHI LANCER EVOLUTION VIII 2004 Workshop Manual

ENGINE (4G6) – GENERAL, BASE ENGINE (6 M/T)19
1. O2 sensor2. Air flow sensor3. Air intake sensor4. Throttle position
sensor
5. Cam position sensor6. Crack angle sensor7. Atmospheric pressure
sensor
8. Water temperature
sensor
9. Knock sensor•Power supply
• Ignition switch IG
•Ignition switch ST
•Vehicle speed sensor
• A/C switch
1. Injector2. ISC servo (stepper
motor)
3. Fuel pressure control
solenoid valve
4. No.1 wastegate solenoid
valve
5. No.2 wastegate solenoid
valve
6. Purge control solenoid
valve
7. Secondary air control
solenoid valve•Engine control relay
•Fuel pump relay 2, 3
•A/C relay
•Ignition coil
• Fan controller
Engine ECU
6. Purge control
solenoid valveCanister
7. Secondary air
control solenoid valveFrom fuel tank
Secondary
air valveBypass
valve
1. O2sensor
3. Fuel pressure
control solenoid valve
4. Throttle
position
sensor
7. Atmospheric pressure
sensor
3. Air intake
sensor2. Air flow sensor
4. No.1
wastegate
solenoid valve
5. No.2 wastegate
solenoid valve
Only operates on 6M/TWastegate actuatorFuel pressure
regulator
1. Injector5.Cam position sensor8.Water temperature sensor
9.Knock sensor
Crack angle sensor
Catalytic converter Air
intakeCheck
valve
2. ISC servo
Vacuum
tank
From fuel
pump To fuel
tank
Control system diagram

MPI General13A2
General
Service information issued contains the changes noted below. Other service details remain unchanged.
• Change from one to two wastegate solenoid valves. However, the No.2 wastegate solenoid valve on the 5 M/T is not
functional.
• Diagnosis code No. P1500 changed to P0622. <6M/T>
MPI system diagram
1.O2 sensor2. Air flow sensor3. Air intake sensor4. Throttle position
sensor
5. Cam position sensor6. Crack angle sensor7.Barometric pressure
sensor
8. Water temperature
sensor
9. Knock sensor•Power supply
• Ignition switch IG
• Ignition switch ST
•Vehicle speed sensor
• A/C switch
• A/C load signal
•Power steering fluid
pressure switch
•Alternator FR signal
•Intercooler water spray
switch (auto)
•Intercooler water spray
switch (manual)
1.Injector2. ISC servo (stepper
motor)
3.Fuel pressure control
solenoid valve
4.No.1 wastegate solenoid
valve
5. No.2 wastegate solenoid
valve
6. Purge control solenoid
valve
7. Secondary air control
solenoid valve•Engine control relay
•Fuel pump relay 2, 3
• A/C relay
•Ignition coil
• Fan controller
• Condenser fan relay (HI)
•Condenser fan relay
(LOW)
•Engine warning lamp
•Diagnosis output
• Alternator G terminal
•Intercooler water spray
relay
•Intercooler water spray
lamp
Engine ECU
6.Purge control
solenoid valveCanister
7.Secondary air
control solenoid valveFrom fuel tank
Secondary
air valveBypass
valve
1. O2sensor
3.Fuel pressure
control solenoid valve
4.Throttle
position
sensor
7. Barometric pressure
sensor
3. Air intake
sensor2. Air flow sensor
4. No.1
wastegate
solenoid valve
5.No.2 wastegate
solenoid valve
Only operates on 6M/TWastegate actuatorFuel pressure
regulator
1. Injector5.Cam position sensor8.Water temperature sensor
9.Knock sensor
Crack angle sensor
Catalytic converter Air
intakeCheck
valve
2.ISC servo
Vacuum
tank
From fuel
pump To fuel
tank

MANUAL TRANSMISSION TROUBLESHOOTING2218
Code No.74 Proportional valve systemAssumed cause of concern
In cases where the proportional valve control circuit
is shorting, code No.74 is output.• Proportional valve malfunction
• Harness, connector malfunction
Remarks*2: refer to ’011 Lancer Evolution VII Service Manual (No.1036K02)
MUTII/III Service data
• No.11 Proportional valve current
OK:P.2232 Refer to (Service Data List)*2
OK > Intermittent malfunction
Measurement at F25 proportional valve
connector
• Undo connector, take measurement on proportional
valve side
• Resistance between 2 3
OK:4.7Ωor less
Measurement at F25 proportional valve
connector
• Undo connector, take measurement on harness side
• Resistance between 2 – body earth
OK:2Ω or less
Connector check:F25, F22
NG > repair
Check harness between proportional valve
body earth
•Check earth wire to see if broken or damaged
NG > repair Replace hydraulic unit
Connector check:F25, F22, C30, C133, C38
NG > repair
Check harness between 4WDECU and Proportional
valve
•Check output wire to see if broken, shorting, or
damaged
NG > repair
MUTII/III Service data
• No.11 Proportional valve current
OK:refer to P.2232 (Service Data List)*2
NG: replace 4WD ECU
OK > Intermittent malfunction
Code No.81 Electric pump relay systemAssumed cause of concern
Output when the circuit on the pump relay coil side is broken
or shorting.• Electric pump relay malfunction
• Harness, connector malfunction
• 4WDECU malfunction
Remarks*2: refer to ’011 Lancer Evolution VII Service Manual (No.1036K02)
MUTII/III actuator test
• No.04 Electric pump operation
OK:the electric pump operating sound is audible
OK > Intermittent malfunction
Check electric pump relay (refer P.2253)
*2
Measurement at B127 electric pump relay connector
• Undo connector, take measurement on harness side
• Resistance between 1 – body earth
OK:2Ωor less
Connector check:B127
NG > repair
Check harness between electric pump relay body earth
•Check earth wire to see if broken or damaged
NG > repair Replace electric pump relay
Connector check:B127, C38
NG > repair
Check harness between 4WDECU and electric pump relay
•Check power supply wire to see if broken, shorting,
or damaged
NG > repair
MUTII/III Actuator test
• No.04 Electric pump operation
OK:the electric pump operating sound is audible
NG:replace 4WD ECU
OK > NG
OK
OK
OK
OK
OK
NG
OK
OK
NG
NG
OK
OK
OK
NG
OK