turn signal MITSUBISHI LANCER SPORTBACK 2010 8.G MMCS Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2010, Model line: LANCER SPORTBACK, Model: MITSUBISHI LANCER SPORTBACK 2010 8.GPages: 161, PDF Size: 14.22 MB
Page 66 of 161
Disk Handling 6-5
Audio
Correct Disk Handling
Handling Precautions If the disk signal surface is contaminated with
fingerprints or other dirt, the disk may become
unreadable. When holding a disk, do not touch the
signal surface. Gently pinch both edges of the disk,
or hold by the center hole and one edge.
Do not af x paper or stickers to the disk, or scratch
the disk.
Do not force a disk into the disk slot while another
disk is already inserted. This may scratch or damage
the disks.Maintenance Periodically clean the disk signal surface. To clean,
use a soft cloth to wipe gently from inside to outside,
without rotating the disk.
Check that there is no residue in the center hole
and around the circumference of new disks. Using
a disk with residue may cause malfunction, so use a
ballpoint pen, etc., to clean away the residue.Storage Precautions When not in use, make sure to return disks to their
cases and store out of direct sunlight.
If not using for a long time, make sure to remove
from the device.Disk Playback Environment Using disks in cold ambient temperatures
immediately after turning on the vehicle heater may
cause malfunction due to condensation (water
droplets) forming on the optical parts of the device,
or on the disk. In such cases, remove the disk and
wait a while before use.
Do not use 8-cm CD adapters. This may cause
malfunction.
Copyright Unauthorized copying, distribution, public
performance, or rental of disks is prohibited by law.
This product uses copyright protection technology,
and Macrovision and other copyright holders are
protected by the patent laws of the United States
and other intellectual property rights.
Use of this copyright protection technology requires
authorization from Macrovision. Further, without
special authorization from Macrovision, use is
restricted to the home and other private appreciation.
Page 148 of 161
Equipment 10-7
Settings
Equipment
Set the vehicle equipment.
1 Press the [SET] key, touch
[Equipment]
eng_a018
The equipment screen is displayed. 2 Touch the name of the equipment
group
eng_a237
3 Touch the item name
eng_a239
4 Touch the condition
eng_a240
5 Touch [Back]
The equipment settings are completed.
Equipment Items that Can Be Set
Refer to the section titled “Features and
Controls” in the vehicle owner’s manual for
details on setting these items.
Keyless Entry System Turn Signal Lights Answerback
Horn Answerback Sounds at Keyless Entry Lock
Duration of Horn Answerback SoundsF.A.S.T.*-key (Keyless Operation System)*:Free-hand Advanced Security Transmitter
Turn Signal Lights Answerback
Horn Answerback Sounds at keyless Entry Lock
Duration of Horn Answerback Sounds
Door Entry and Engine Start Function
Keyless Operation Answerback Beep Sounds
Time for Remote Unlock Inactivated after LockingNOTE Either “Keyless Entry System” or “Keyless Operation
System” will be displayed, depending on the equipment.
Wipers Windshield Wipers Intermittent Operation
Wipers Linked to Washer
Rear Wiper Intermittent Interval
Rear Wiper Continuous OperationExterior Lights/Interior Lights Headlight Auto-cutout Function
Interior Light Auto-cutout Time
Duration Dome Light Remains On after Door is
ClosedTheft Alarm Panic AlarmTurn Signal Operation in Key Position
Lane-change Signals (Flash Three Times with 1
Touch)Power Door Locks Automatic Relocking after Unlocked by Remote
Unlock Operation
Automatic Unlock when Transmission Shifted to ParkOthers Auto Cut of ACC Power