coolant MITSUBISHI MONTERO 1991 Service Manual

\003
I - S YSTE M /C O M PO NEN T T E STS

1991 M it s u bis h i M onte ro
1991 ENGINE PERFORMANCE
System & Component Testing
Chrysler Motors: Ram-50
Mitsubishi: Montero, Pickup
INTRODUCTION
Before testing separate components or systems, perform
procedures in F - BASIC TESTING article in the ENGINE PERFORMANCE
Section. Since many computer controlled and monitored components set a
trouble code if they malfunction, also perform procedures in G - TESTS
W/CODES article in the ENGINE PERFORMANCE Section.
NOTE: Testing individual components does not isolate shorts or
opens. Perform all voltage tests with a Digital
Volt-Ohmmeter (DVOM) with a minimum 10-megohm input
impedance, unless stated otherwise in test procedure. Use
ohmmeter to isolate wiring harness shorts or opens.
COMPUTERIZED ENGINE CONTROLS
CONTROL UNIT
NOTE: To identify ECU power and ground circuits, see appropriate
L - WIRING DIAGRAMS article in the ENGINE PERFORMANCE
Section.
Ground Circuits
1) ECU is located near right kick panel. Turn ignition off.
Using an ohmmeter, check for continuity between ground and ECU
terminals No. 101 and 106. Resistance should be zero ohms. If
resistance is not zero ohms, repair open circuit between ECU connector
and ground.
2) Connect voltmeter negative lead to ground. Connect
positive lead to ECU ground terminals as in step 1). With vehicle
running, voltmeter should indicate less than one volt. If voltmeter
reading is greater than one volt, check for open, corrosion or loose
connection in ground circuit.
Power Circuits
ECU is located near right kick panel. Turn ignition on. Check
for battery voltage on ECU terminals No. 102 and 107. If battery
voltage is not present, check operation of MPI control relay. See
RELAYS under MOTORS, RELAYS & SOLENOIDS.
ENGINE SENSORS & SWITCHES
BAROMETRIC PRESSURE SENSOR
Sensor is a component part of airflow sensor assembly. See G
- TESTS W/CODES article in the ENGINE PERFORMANCE Section.
COOLANT TEMPERATURE SENSOR
1) Remove coolant temperature sensor located near thermostat
housing (2-wire connector). Place end of sensor in water with terminal\

connector portion of sensor slightly above water.
2) Gradually heat water and read resistance values across
terminal connectors. See COOLANT TEMPERATURE SENSOR RESISTANCE table.
If resistance is not within specification, replace sensor.
COOLANT TEMPERATURE SENSOR RESISTANCE TABLE









\









\









\









\









TemperatureF (C) Ohms
Montero & Pickup 3.0L
32 (0) ............................. 5900
68 (20) ............................ 2500
104 (40) ........................... 2700
176 (80) ............................ 300
All Others
32 (0) ............................. 5900
68 (20) ............................ 2500
104 (40) ........................... 1100
176 (80) ............................ 300









\









\









\









\









CRANK ANGLE SENSOR
See IGNITION SYSTEM.
DETONATION SENSOR
See IGNITION SYSTEM.
EGR TEMPERATURE SENSOR
California
See EXHAUST GAS RECIRCULATION (EGR) under EMISSION SYSTEMS &
SUB-SYSTEMS.
IDLE POSITION SWITCH
NOTE: Idle position switch is incorporated in idle speed control
motor assembly, motor position sensor or throttle position
sensor, depending upon vehicle application.
Pickup 2.4L & Ram-50 2.4L
1) Disconnect motor position sensor (MPS) connector. Connect\
ohmmeter lead between ground and MPS connector terminal No. 4. See
Fig. 2 .
2) With accelerator pedal pressed, no continuity should be
present. With accelerator pedal released, continuity should be
present. If switch continuity is not as specified, replace MPS.
Montero, Pickup 3.0L & Ram-50 3.0L
1) Disconnect throttle position sensor (TPS) connector.
Connect ohmmeter between TPS connector terminals No. 1 and 2. See
Fig. 6 .
2) With accelerator pedal pressed, no continuity should be
present. With accelerator pedal released, continuity should be
present. If idle switch continuity is not as specified, replace TPS.
INHIBITOR SWITCH
Automatic Transmission
Switch is mounted to automatic transaxle, near shift lever

specified range, replace MPS.
CAUTION: DO NOT apply more than 6 volts to ISC motor.
3) Operate ISC motor by connecting a 6-volt source directly
to appropriate terminals of ISC motor connector. For ISC motor
operation test procedures, see IDLE SPEED CONTROL (ISC) MOTOR
OPERATION TEST under IDLE CONTROL SYSTEM.
4) While operating ISC motor, measure resistance between MPS
connector terminals No. 3 and 5. Observe ohmmeter during ISC motor
operation. If MPS resistance does not vary within a 4000-6000 ohm
range or if resistance does not change smoothly, replace MPS (vehicles
equipped with separate MPS) or ISC motor assembly (vehicles equipped
with MPS incorporated in ISC).
OXYGEN SENSOR
1-Wire Or 2-Wire
1) On all models, warm engine until coolant temperature is
185-205
F (85-96C). Disconnect oxygen sensor connector. See Fig. 3 or
4.
2) Connect digital voltmeter between terminal No. 1 and
ground. Repeatedly race engine and observe oxygen sensor output
voltage. If output is not 0.6-1.0 volt, replace oxygen sensor.
Fig. 3: O2 Sensor Connector Terminal ID (1 Wire)
Courtesy of Mitsubishi Motor Sales of America.

Fig. 4: O2 Sensor Connector Terminal ID (2 Wire)
Courtesy of Mitsubishi Motor Sales of America.
4-Wire Heated
1) Warm engine until coolant temperature is 185-205
F (85-

right several times. Start engine, and turn steering wheel back and
forth to raise fluid temperature to approximately 122-140F (50-60C).
3) With engine idling, gradually close shutoff valve of
pressure gauge to increase hydraulic pressure. If idle speed does not
increase 200-250 RPM when fluid pressure reaches 213-284 psi (15-20
kg/cm
), replace power steering idle-up switch.
4) Gradually open shutoff valve. If engine speed does not
return to curb idle speed between 100-142 psi (7-10 kg/cm
), replace
power steering idle-up switch. Remove testing equipment. Bleed air
from system as in step 2).
IGNITION SYSTEM
NOTE: For basic ignition checks, see F - BASIC TESTING article in
ENGINE PERFORMANCE Section.
TIMING CONTROL SYSTEMS
Crank Angle Sensor
Crank angle sensor is located inside distributor on SOHC
engines and is attached to cylinder head on DOHC engines. If
malfunction occurs, Code 22 will set. For testing procedure, see
appropriate G - TESTS W/CODES article in the ENGINE PERFORMANCE
Section.
EMISSION SYSTEMS & SUB-SYSTEMS
EXHAUST GAS RECIRCULATION (EGR)
System Testing (Federal)
1) Disconnect Green-striped hose from throttle body, and
connect vacuum pump to hose end. Plug nipple where hose was connected
to throttle body. When engine is cold, 122
F (50C) or less, and at
idle, apply vacuum to disconnected hose. If idle does not change and
vacuum bleeds down, system is okay.
2) When engine is hot, 205
F (95C), and at idle, apply 1.8
in. Hg. If idle does not change and vacuum holds, system is okay.
Using a vacuum pump, apply 7.7 in. Hg. If idle becomes unstable or
engine stalls (and vacuum holds), system is okay.
System Testing (California)
1) Connect vacuum "T" fitting into Green-striped hose from
EGR valve, and connect vacuum gauge to vacuum tee. When engine coolant
temperature is 68
F (20C) or less and engine is idling, snap throttle
open to race engine. If no change in vacuum reading is detected on
gauge, system is okay.
2) When engine coolant temperature is 158
F (70C) or more
and engine is idling, snap throttle open to race engine. If vacuum
increases to 3.9 in. Hg or higher, system is okay.
3) Using vacuum pump, apply specified vacuum to open EGR
valve. See EGR VALVE SPECIFICATIONS table. If idle becomes unstable or
engine stalls, system is okay.
EGR Control Solenoid Valve (Pickup & Ram-50, California)
1) EGR control solenoid valve is located near left shock
tower. Label and disconnect vacuum hoses and wiring harness from
solenoid valve.
2) Connect hand vacuum pump to vacuum nipple where Green-
striped vacuum hose was connected. Apply vacuum and ensure vacuum does
not hold. Apply battery voltage to one terminal of solenoid, and
ground other. Ensure vacuum holds.

3) Using an ohmmeter, measure resistance between terminals of
solenoid valve. At room temperature, reading should be 36-44 ohms.
Replace solenoid if not to specification.
NOTE: EGR temperature sensor only determines if EGR is operating.
An inoperative sensor will not affect driveability or
exhaust emissions.
EGR Temperature Sensor (California)
1) Remove EGR temperature sensor from EGR valve. Place EGR
temperature sensor in water. While increasing water temperature,
measure resistance between wire terminals.
2) At a temperature of 122
F (50C), resistance should be 60,
000-80,000 ohms. At 212F (100C), resistance should be 11,000-14,000
ohms. Replace EGR temperature sensor if resistance differs
significantly from specifications.
EGR Valve
1) Remove EGR valve. Check valve for sticking, carbon
deposits and damage. Clean valve with solvent if necessary. Apply 19.8
in. Hg to valve diaphragm. If valve does not hold vacuum, replace
valve.
2) Apply specified vacuum to valve diaphragm. See CLOSED IN.
HG in EGR VALVE SPECIFICATIONS table. If valve begins to open below
specification, replace valve.
3) Apply specified vacuum to valve diaphragm. See OPEN IN. HG
in EGR VALVE SPECIFICATIONS table. If valve is not completely open at
or above specification, replace valve.
EGR VALVE SPECIFICATIONS TABLE









\









\









\









\









\









\

Application Closed Open
In. Hg In. Hg
Montero ....................... 2.4 ........... 6.7
Pickup & Ram-50 ............... 1.2 ........... 9.4









\









\









\









\









\









\

FUEL EVAPORATION
System Test
1) Disconnect Red-striped purge hose from throttle body, and
connect to hand vacuum pump. Plug nipple on throttle body where purge
hose was removed.
2) With engine coolant temperature at 140
F (60C) or less
and engine idling, apply 14.8 in. Hg. Vacuum should hold. Raise engine
speed to 3000 RPM and again apply 14.8 in. Hg. Vacuum should hold.
3) With engine coolant temperature at 158
F (70C) or more
and engine idling, apply 14.8 in. Hg. Vacuum should hold. Turn engine
off. Start engine and within 3 minutes of starting engine, apply
vacuum. Vacuum should bleed down.
4) With engine running for more than 3 minutes after
starting, raise engine speed to 3000 RPM and apply 14.8 in. Hg. Vacuum
should hold momentarily and then bleed down.
NOTE: In step 4), vacuum should bleed down continuously if vehicle
is at an altitude of 7200 ft. (2200 m) or higher or if
intake air temperature is 122
F (50C) or higher.
Purge Control Solenoid Valve
1) Purge control solenoid valve is located near left shock
tower. Label and disconnect both vacuum hoses from solenoid valve.
Disconnect electrical connector. Connect hand vacuum pump to solenoid

Fig. 4: 18-Way ECU Connector
Courtesy of Chrysler Motors.
Fig. 5: 24-Way ECU Connector
Courtesy of Chrysler Motors.
Fig. 6: Self-Diagnostic Connector Terminal Identification
Courtesy of Mitsubishi Motor Sales of America.
FAULT CODES
FAULT CODES TABLE








\









\









\









\









\









\






Fault Code System Fault Description
11 .................... Open or short in O2 sensor circuit
12 ............... Open or short in airflow sensor circuit
13 ...... Open or short in intake air temp. sensor circuit
14 .......................... Open or short in TPS circuit
15 (1) .... Open or short in motor position sensor circuit
21 ......... Open or short in coolant temp. sensor circuit
22 ........ No voltage change in crank angle sensor signal
23 ............... No voltage change in TDC sensor circuit
24 ( 2) .. No voltage change in vehicle speed sensor signal
25 ........... Open or short in barometric pressure sensor
31 ( 3) ........ Open or short in detonation sensor circuit
41 ..................... Open or short in injector circuit
42 .............. Open or short in fuel pump drive circuit
43 ( 4) ......... Open or short in EGR temp. sensor circuit

Fig. 39: Flow Chart DR-6 (1.5L) (2 of 2)
DR-7: CODE 21 COOLANT TEMP. SENSOR CIRCUIT - 1.5L

Fig. 115: Flow Chart DR-6 (1.6L) (3 of 3)
DR-7: CODE 21 COOLANT TEMPERATURE CIRCUIT - 1.6L
Fig. 116: Circuit Diagram DR-7 (1.6L)

Fig. 200: Flow Chart DR-6 (1.8L) (2 of 2)
DR-7: CODE 21 COOLANT TEMP. SENSOR CIRCUIT - 1.8L