lock MITSUBISHI MONTERO 1991 Service Manual

Check camber. If camber is not within specification, loosen
eccentric cam nut. Rotate eccentric cam bolt to obtain correct camber.
See Fig. 2 . Each marking represents a change of 1/8-1/4 degree of
camber.
Fig. 2: Adjusting Camber (Stealth & 3000GT)
Courtesy of Mitsubishi Motor Sales of America.
All Other Models
Check camber using a camber/caster/kingpin gauge and turning
radius gauge. See WHEEL ALIGNMENT SPECIFICATIONS table. If camber is
not within specification, replace damaged or bent parts.
CASTER ADJUSTMENT
Colt Vista
Check tire inflation. Place front wheel on turning radius
gauge, and level vehicle (unladed). Remove hub cap and cotter pin.
Measure caster with camber/caster/kingpin gauge attached. See WHEEL
ALIGNMENT SPECIFICATIONS table. If caster is not within specification,
adjust by changing strut bar lock position. See Fig. 3.
Fig. 3: Adjusting Caster (Colt Vista)
Courtesy of Mitsubishi Motor Sales of America.
Montero

Remove free wheeling hub. Measure caster with
camber/caster/kingpin gauge and turning radius gauge. See WHEEL
ALIGNMENT SPECIFICATIONS table. If caster is not within specification,
remove upper arm from crossmember. Adjust caster by turning upper arm
shaft. See Fig. 4.
Fig. 4: Adjusting Caster (Montero)
Courtesy of Mitsubishi Motor Sales of America.
Pickup & Ram-50
1) Check tire inflation. Place front wheel on turning radius
gauge, and level vehicle (unladed). On 2WD models, remove hub cap and
cotter pin. On 4WD models, remove free wheeling hub assembly.
2) On all models, measure caster with camber/caster/kingpin
gauge attached. See WHEEL ALIGNMENT SPECIFICATIONS table. If caster is
not within specification, remove shock absorber mounting nut and lock
nut.
3) Compress shock absorber and loosen upper arm mounting
bolts and nuts. Adjust caster by increasing or decreasing shims
between upper arm shaft and crossmember. See Fig. 1.
CAUTION: Difference in shim thickness between front and rear must be
.16" (4 mm) or less. DO NOT use more than 3 shims at one
location.
All Other Models
Check caster using a camber/caster/kingpin gauge and turning
radius gauge. See WHEEL ALIGNMENT SPECIFICATIONS table. If caster is
not to specification, replace damaged or bent parts.
TOE-IN ADJUSTMENT
Check toe-in. See WHEEL ALIGNMENT SPECIFICATIONS table. If

WIR IN G D IA G RAM S

1991 M it s u bis h i M onte ro
1991 Wiring Diagrams
Mitsubishi
Montero
IDENTIFICATION
COMPONENT LOCATION MENU
COMPONENT LOCATIONS TABLE








\









\









\









\









\









\






Component Figure No. (Location)
A/C RELAYS .......................... 4 (C 12), 4 (A-B 15)
A/C SYSTEM ................................. 4 (A-C 12-15)
ALTERNATOR ................................... 1 (B-C 1-2)
ALTERNATOR RELAY ............................... 1 (C 1-2)
AUTO FREE-WHEELING HUB CONTROL UNIT ............. 3 (D 11)
BACK DOOR LOCK SW ............................... 7 (B 27)
BACK-UP LT SW (M/T) ............................. 7 (A 26)
BATTERY .......................................... 1 (A 1)
BLOWER SWITCH ................................. 4 (A-B 12)
BUZZER .......................................... 5 (E 17)
CARGO LIGHT ..................................... 6 (A 23)
CIG LIGHTER ..................................... 3 (E 11)
CLOCK ........................................... 3 (E 11)
COLUMN SW ..................................... 5 (A-E 19)
CRUISE CONTROL SYSTEM ...................... 4 (D-E 13-15)
DEFOGGER ...................................... 7 (C-D 27)
DIAG CONNECTION .................................. 2 (E 7)
DIMMER CONTROL SWITCH ............................ 3 (E 8)
DIR FLASHER ..................................... 5 (C 16)
DIR SWITCH ...................................... 5 (C 19)
DOME LT ............................... 6 (A 23), 7 (A 24)
DOOR LOCK SYSTEM ........................... 6 (D-E 21-23)
DOOR SWITCHES ......................... 5 (D 17), 6 (C 23)
FRONT WIPER SYSTEM ........................... 5 (A 16-17)
FUEL GAUGE UNIT ................................. 6 (C 22)
FUEL PUMP ........................................ 2 (C 4)
FUSE BLOCK .................................... 3 (C 9-10)
HAZARD FLASHER .................................. 5 (C 16)
HAZARD SW ....................................... 5 (B 16)
HEAD LIGHT WASHER RELAY ....................... 5 (C-D 17)
HEATER RELAY .................................... 4 (A 12)
HORN SWITCH ..................................... 5 (E 19)
IGNITION COIL .................................... 2 (E 4)
IGNITION SW ..................................... 3 (A 11)
ILLUMINATION LIGHTS ............................ 3 (D-E 8)
INHIBITOR SW ..................................... 3 (A 9)
INSTRUMENT CLUSTER ............................ 6 (A-D 20)
KEY REMINDER SW ................................. 5 (E-17)
LIGHT CONTROL RELAY ............................. 5 (E 19)
LIGHT SWITCH .................................... 5 (D 19)
MAIN FUSE LINKS ................................ 1 (A 1-2)
METER UNIT ...................................... 6 (E 20)
MPI CONTROL RELAY ................................ 2 (B 4)
MPI CONTROL UNIT ............................... 2 (A 4-7)
NOISE FILTER ..................................... 2 (E 6)
OVERDRIVE CONTROL RELAY .......................... 3 (A 8)

Fig. 3: Fuse Block, Ignition Sw, Inhibitor Sw, (A/T) (Grid 8-11)

Fig. 6: Inst Cluster, Door Locks, Interior Lights (Grid 20-23)