tow MITSUBISHI MONTERO 1991 User Guide

\003
A/C C O M PR ESSO R S ER VIC IN G

1991 M it s u bis h i M onte ro
1991 GENERAL SERVICING
Compressor Service
* PLEASE READ THIS FIRST *
CAUTION: When discharging air conditioning system, use only approved
refrigerant recovery/recycling equipment. Make every attempt
to avoid discharging refrigerant into the atmosphere.
ISOLATING COMPRESSOR
NOTE: Only compressors with stem-type service valves can be
isolated.
1) Connect service gauge set to the compressor service valves
and open compressor valves slightly (turn in clockwise). Start engine
and operate air conditioning. Slowly turn compressor suction valve
clockwise toward closed (front-seated) position.
2) When suction pressure is reduced to zero or less, turn off
engine and compressor and quickly turn suction valve stem in to full
front-seated position. Suction pressure should be slightly above zero.
Turn discharge valve into front-seated position.
3) To check oil level, slowly open compressor crankcase plug
to relieve any remaining pressure. After oil level is corrected, cap
service gauge ports on both valves. Back-seat suction service valve to
allow refrigerant to enter compressor. Open discharge valve halfway.
4) Loosen discharge service valve cap, allowing refrigerant
pressure to force air out of compressor. Back-seat service valve and
tighten cap. Compressor is now ready for operation.
REFRIGERANT OIL
Only new, pure, moisture-free refrigerant oil should be used
in the air conditioning system. This oil is highly refined and
dehydrated to a point where moisture content is less than 10 parts per
million. The oil container must be tightly closed at all times when
not in use, or moisture will be absorbed into the refrigerant oil from
the air.
DISCHARGING SYSTEM PRECAUTIONS
CAUTION: When discharging air conditioning system, use only approved
refrigerant recovery/recycling equipment. Make every attempt
to avoid discharging refrigerant into the atmosphere.
If compressor has stem-type service valves, it can be
isolated and removed without discharging entire system. Otherwise,
discharge system completely using approved refrigerant
recovery/recycling equipment before loosening any fittings.
DISCONNECTING LINES & FITTINGS TEST
After system is discharged, carefully clean area around all
fittings to be opened. Always use 2 wrenches when tightening or
loosening fittings to avoid twisting or distorting lines. Cap or plug
all openings as soon as lines are removed. Do not remove caps until

Installer (49 UN01 046) and 2-jaw puller engaged to rear side of
compressor front mounts to press coil into place.
2) Install pulley assembly. Install pulley assembly snap ring
with bevel side of snap ring facing out. Install shim(s) and clutch
plate. Install a NEW clutch plate retaining bolt and tighten to
96-120 INCH lbs. (11-14 N.m).
3) Use a feeler gauge to check clearance between clutch plate
and pulley assembly. Clearance should be .018-.033" (.46-.84 mm). If
clearance is incorrect, add or remove shims as necessary.
FORD FX-15 SHAFT SEAL R & I
Removal
1) Using Clutch Holder (000 41 0812 05), remove clutch plate\
retaining bolt and discard. Using an 8 mm bolt threaded into clutch
plate, remove clutch plate and shim(s). See Fig. 6.
2) Remove shaft felt seal. Thoroughly clean seal area of
compressor. Remove shaft seal retaining snap ring. Position Shaft Seal
Remover (49 UN01 044) over compressor shaft.
3) Push shaft seal remover downward against seal. Ensure end
of shaft seal remover is engaged with inside of seal. Rotate shaft
seal remover clockwise to expand remover tip inside seal. Pull shaft
seal from compressor.
Installation
1) Lubricate shaft seal protector and shaft seal with
refrigerant oil. Install shaft seal on shaft seal protector so lip
seal is toward compressor (large end of shaft seal protector).
2) Install shaft seal protector on compressor shaft. Using
shaft seal installer (49 UN01 043), push shaft seal down seal
protector until seal is seated.
3) Remove shaft seal installer and protector. Install a NEW
shaft seal retaining snap ring and shaft seal felt. Install shim(s)
and clutch plate. Install a NEW clutch plate retaining bolt and
tighten to 91-120 INCH lbs. (11-14 N.m).
4) Use a feeler gauge to check clearance between clutch plate
and pulley assembly. Clearance should be .018-.033" (.46-.84 mm). If
clearance is incorrect, add or remove shims as necessary.
Fig. 6: Exploded View of Compressor Clutch (Ford FX-15)
Courtesy of Mazda Motors Corp.
HARRISON R4 4-CYL CLUTCH R & I

article, see appropriate HEATER SYSTEM article in the AIR
CONDITIONING & HEAT Section.
A/C SWITCH
Removal & Installation (Colt Vista)
From back side of control panel, push right control panel
clip right while pushing control panel out of dash panel. Allow
control panel to hang. Remove side bracket. Press temperature switch
control assembly left, and then remove A/C switch. To install, reverse
removal procedure.
Removal & Installation (Montero)
Remove lap heater duct. Remove glove box stoppers and glove
box. Remove heater control knobs. Remove center panel screw hole
plugs, and remove screws. Remove center panel. Disconnect center panel
wiring harness. Remove A/C switch. To install, reverse removal
procedure.
Removal & Installation (Pickup & Ram-50)
Remove heater control knobs. Remove glove box. Remove center
panel mounting screws. Use a trim stick to remove upper side of panel.
Remove A/C switch assembly mounting screws. Pull switch assembly
toward vehicle interior. Remove switch. To install, reverse removal
procedure.
COMPRESSOR
Removal & Installation (Colt Vista)
Discharge A/C system using approved refrigerant
recovery/recycling equipment. Disconnect high tension cable from
ignition coil. Remove distributor cap. Loosen idler pulley adjusting
bolt, and remove belt. Disconnect compressor electrical connector.
Remove high and low pressure lines and "O" rings from compressor.
Remove compressor mounting bolts. Remove compressor. To install,
reverse removal procedure.
Removal & Installation (Montero, Pickup & Ram-50)
DischargeA/C system using approved refrigerant
recovery/recycling equipment. Loosen idler pulley, and remove belt.
Disconnect compressor electrical connector. Disconnect high and low
pressure lines from compressor. Remove compressor mounting bolts.
Remove compressor. To install, reverse removal procedure.
CONDENSER
Removal & Installation (Colt Vista)
Discharge A/C system using approved refrigerant
recovery/recycling equipment. Remove front grille and grille brackets.
Remove front end cover and condenser harness. Disconnect electrical
fan connector. Slowly disconnect pressure lines from condenser. Remove
2 condenser mounting bolts. Lift up and remove condenser from vehicle.
To install, reverse removal procedure.
Removal & Installation (Montero)
Discharge A/C system using approved refrigerant
recovery/recycling equipment. Remove radiator grille. Slowly
disconnect pressure lines from condenser. Disconnect condenser fan
motor connector. Remove condenser fan mounting bolts and motor. Remove
condenser mounting bolts. Remove condenser from vehicle. To install,
reverse removal procedure.
Removal & Installation (Pickup & Ram-50)

are continually republished. In addition to these, standards for Drive
Train and Transmissions have recently been promulgated. Participating
shops utilize these Uniform Inspection & Communication Standards as
part of the inspection process and for communicating their findings to
their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not
satisfied with a repair transaction, the Motorist Assurance Program
offers mediation and arbitration through MAP/BBB-CARE and other non-
profit organizations. MAP conducted pilot programs in twelve states
before announcing the program nationally in October, 1998. During the
pilots, participating repair shops demonstrated their adherence to the
Pledge and Standards and agreed to follow the UICS in communicating
the results of their inspection to their customers. To put some
"teeth" in the program, an accreditation requirement for shops was
initiated. The requirements are stringent, and a self-policing method
has been incorporated which includes the "mystery shopping" of
outlets.
We welcome you to join us as we continue our outreach... with
your support, both the automotive repair industry and your customers
will reap the benefits. Please visit MAP at our Internet site www.
motorist.org or contact us at:
1444 I Street, NW Suite 700
Washington, DC 20005
Phone (202) 712-9042 Fax (202) 216-9646
January 1999
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, steering,
suspension, wheel alignment, drive-line, engine performance and
maintenance, and heating, ventilation and air conditioning, and
electrical services be offered and performed under the standards and
procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be "Required" or
"Suggested". In addition, suggestions may be made to satisfy the
requests expressed by the customer.
When a component is suggested or required to be repaired or
replaced, the decision to repair or replace must be made in the
customer's best interest, and at his or her choice given the options
available.
This section lists the various parts and conditions that
indicate a required or suggested service or part replacement.
Although this list is extensive, it is not fully inclusive. In
addition to this list, a technician may make a suggestion. However,
any suggestions must be based on substantial and informed experience,

2.0L .............................. Yellow/Red ............. (5)\
Montero
3.0L ............................. White/Yellow ............ (4)\
Pickup & Ram-50
2.4L .............................. Black/Blue ............. (6)\
3.0L ............................. White/Yellow ............ (6)\
Stealth (SOHC)
3.0L ............................. White/Yellow ............ (4)\
Stealth & 3000GT (DOHC)
3.0L (Non-Turbo) ................. Black/Green ............. (4\
)
3.0L (Turbo) ..................... White/Yellow ............ (4\
)
(1) - Remove waterproof female connector (if equipped) for access to\
wire.
(2) - Ground connector at wire end for basic timing adjustment.
(3) - On main wiring harness, near center of firewall.
(4) - On main wiring harness, near wiper motor on firewall.
(5) - On main wiring harness, near master cylinder on firewall.
(6) - Between right shock tower and firewall.
(7) - Near front of right shock tower.









\









\









\









\









\









\









\







IDLE SPEED & MIXTURE
NOTE: Perform adjustments with engine at normal operating
temperature, cooling fan and accessories off, transmission
in Park or Neutral, and front wheels in straight-ahead
position.
CURB (SLOW) IDLE SPEED
NOTE: Curb idle speed is controlled by Idle Speed Control (ISC)
motor. Adjustment is usually not necessary. For curb idle
speed specifications, see IDLE SPEED SPECIFICATIONS table
under BASIC IDLE SPEED.
1) Check ignition timing and adjust if necessary. Run engine
at 2000-3000 RPM for more than 5 seconds. Allow engine to idle for 2
minutes. Check curb idle speed.
2) If curb idle speed is not within specification, check ISC
system. If ISC system is okay, adjust basic idle speed. See BASIC IDLE
SPEED.
BASIC IDLE SPEED
NOTE: ALWAYS check TPS adjustment after adjusting basic idle
speed. See THROTTLE POSITION SENSOR (TPS).
BASIC IDLE SPEED TEST APPLICATION TABLE









\









\









\









\









Application Test
1.5L
Colt, Colt 200,
Mirage & Summit ............. TEST NO. 1
1.6L
Mirage ....................... TEST NO. 2
1.8L
Eclipse ...................... TEST NO. 1
2.0L (VIN V)
Colt Vista & Galant .......... TEST NO. 1
2.0L (VIN R & U)

TESTING CRANK ANGLE SENSOR CIRCUIT - G - TESTS W/CODES article in the
ENGINE PERFORMANCE section.
On Eclipse and Laser, see NS-4A: REPAIRING CRANK ANGLE SENSOR
in G - TESTS W/CODES - 1.8L article.
On Ram-50, Stealth, Pickup and 3000GT testing information not
available at time of publication.
DISTRIBUTORLESS IGNITION SYSTEM (DIS)
Ignition Coil Resistance (4-Cyl Vehicles Except Eclipse 2.0L)
1) Using a Digital Volt/Ohmmeter (DVOM), measure primary coi\
l
resistance between ignition coil connector terminals No. 2 and No. 3
(coils for cylinders No. 1 and No. 4) and terminals No. 1 and No. 3
(coils for cylinders No. 2 and No. 3). See Fig. 2.
Fig. 2: Testing Ignition Coil Primary Resistance (4-Cylinder)
Courtesy of Mitsubishi Motor Sales of America.
2) Measure secondary coil resistance between coil towers for
cylinders No. 1 and No. 4 and between coil towers for cylinders No. 2
and No. 3. See Fig. 3. Primary and secondary coil resistance should be
within specification. See DIS IGNITION COIL RESISTANCE table.
Fig. 3: Testing Ignition Coil Secondary Resistance (4-Cylinder)
Courtesy of Mitsubishi Motor Sales of America.

Ignition Coil Resistance (Eclipse 2.0L)
1) Using a DVOM, measure primary coil resistance between
ignition coil connector terminals No. 2 and No. 4 (coils for cylinders
No. 1 and No. 4) and between terminals No. 4 and No. 1 (coils for
cylinders No. 2 and No. 3). See Fig. 2.
2) Measure secondary coil resistance between coil towers for
cylinders No. 1 and No. 4 and between coil towers for cylinders No. 2
and No. 3. See Fig. 3. Primary and secondary coil resistance should be
within specification. See DIS IGNITION COIL RESISTANCE table.
DIS IGNITION COIL RESISTANCE TABLE Ohms @ 68
F (20C)








\









\









\









\









\









\

Application Primary Secondary
All Models ........... .77-.95 .......... 10.3-13.9









\









\









\









\









\









\

Power Transistor (Eclipse)
1) Disconnect power transistor connector. Using an analog
ohmmeter, connect positive ohmmeter lead to terminal No. 7 and
negative lead to terminal No. 3. See Fig. 4. Ensure there is no
continuity.
Fig. 4: Power Transistor Connector ID (Eclipse)
Courtesy of Mitsubishi Motor Sales of America.
2) Using a 1.5-volt dry cell battery, connect positive end of
1.5-volt battery to power transistor terminal No. 6 and negative end
to terminal No. 3. Ohmmeter should now read continuity between power
transistor terminals No. 7 and No. 3.
3) Connect positive end of 1.5-volt battery to power
transistor terminal No. 2 and negative end to terminal No. 3. Connect
positive ohmmeter lead to terminal No. 1 and negative lead to terminal
No. 3. Ohmmeter should read continuity. Replace power transistor if it
does not test as described.
Power Transistor (Colt Vista, Galant, Montero, Pickup &
Ram-50)
1) Disconnect power transistor connectors. Using a DVOM,
connect positive ohmmeter lead to terminal No. 2 and negative lead to
terminal No. 3. See Fig. 5. Ensure there is no continuity.

(2) Analog Ohmmeter (2) With 1.5 V Battery
Cylinders Connected Between Connected Between
Tested Terminals (No 1.5 V Battery) Terminals\
1 & 4 ......... 3 & 7 No Continuity ....... 6 & 7 Continuity
2 & 5 ......... 2 & 7 No Continuity ....... 5 & 7 Continuity
3 & 6 ......... 1 & 7 No Continuity ....... 4 & 7 Continuity
(1) - All tests performed with power transistor disconnected. Replace
power transistor if it does not test as described.
(2) - See Fig. 8 for terminal identification.









\









\









\









\









\









\









\







MAGNETIC & OPTICAL IGNITION
Ignition Coil Resistance
1) Using a DVOM, measure primary coil resistance between
positive and negative terminals of coil. See Fig. 9. For ignition coil
terminal identification See Fig. 11 - 13.
2) Measure secondary coil resistance between coil positive
terminal and ignition coil tower. See Fig. 10.
3) Primary and secondary coil resistance should be within
specification. See IGNITION COIL RESISTANCE table.
Fig. 9: Testing Ignition Coil Primary Resistance (6-Cylinder)
Courtesy of Mitsubishi Motor Sales of America.

SHOE HARDWARE
SHOES
SOCKETS
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)
STEEL BRAKE LINES
STOPLIGHT SWITCHES
SWITCHES
TIRES
TOOTHED RINGS (TONE WHEEL)
VACUUM BOOSTERS
VACUUM HOSES
VALVES
WHEEL ATTACHING HARDWARE
WHEEL BEARINGS, RACES AND SEALS
WHEEL CYLINDERS
WIRING HARNESSES
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt:\
1) a Pledge of Assurance to their Customers and
2) the Motorist Assurance Program Standards of Service.
All participating service providers have agreed to subscribe
to this Pledge and to adhere to the promulgated Standards of Service
demonstrating to their customers that they are serious about customer
satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
are continually re-published. In addition to these, standards for
Drive Train and Transmissions have recently been promulgated.
Participating shops utilize these Uniform Inspection & Communication
Standards as part of the inspection process and for communicating
their findings to their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not

brake pedal to center shoes, and check pedal travel. Rotate brake drum
to verify free movement.
STOPLIGHT SWITCH
Loosen lock nut, and adjust switch-to-pedal arm clearance to
.02-.04" (.5-1.0 mm). Tighten lock nut. DO NOT depress master cylinder
push rod during stoplight switch adjustment.
TESTING
POWER BRAKE UNIT
Check Valve Inspection
Remove vacuum hose from power brake unit. Remove check valve
from hose (if possible). Using a vacuum pump, ensure airflow is in
direction of intake manifold only.
System Check
1) Run engine for 2 minutes, and shut it off. Depress brake
pedal several times with normal pressure. If pedal height gradually
becomes higher with successive applications, power brake unit is okay.
If pedal height remains steady, power brake unit is faulty.
2) With engine stopped, depress brake pedal repeatedly until
it's height no longer falls. Hold brake pedal down, and start engine.
If pedal moves downward slightly, power brake unit is okay. If pedal
height does not change, power brake unit is faulty.
3) With engine running, press and hold brake pedal and shut
off engine. Hold brake pedal for 30 seconds. Brake pedal height should
not change. If pedal height falls, power brake unit is faulty.
LOAD-SENSING PROPORTIONING VALVE (LSPV) (PICKUP & RAM-50)
1) Before diagnosing Load-Sensing Proportioning Valve (LSPV)\
,
ensure all other brake components are operating properly. When all
other brake system components are determined to be okay, perform LSPV
test beginning with next step.
2) Ensure unladen vehicle is on level ground. Ensure lever is
not contacting stopper bolt. See Fig. 1.
3) When lever is pushed toward valve, distance from LSPV
lever hole and support hole must be 6.97-7.09 in. (177-180 mm). If
measured distance is not within specification, loosen support bolt.
Adjust support until measured distance is within specification.
4) After measured distance is within specification, connect
pressure gauges to input and output ports of LSPV. See Fig. 4. Bleed
brake system. See BLEEDING BRAKE SYSTEM .
Fig. 4: Connecting Pressure Gauges to LSPV (Pickup & Ram-50)
Courtesy of Mitsubishi Motor Sales of America.