service MITSUBISHI MONTERO 1991 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 1071 of 1333
2. ENGINE IGNITION TIMING - Must be set with timing terminal
grounded.
3. ENGINE VACUUM - Must be normal for your altitude.
4. ENGINE VALVE TIMING - To specifications.
5. ENGINE COMPRESSION - To specifications.
6. ENGINE P.C.V. SYSTEM - Must flow freely.
7. ENGINE EXHAUST SYSTEM - Must be free of any restrictions.
8. POWER BRAKE BOOSTER - No internal vacuum leaks.
9. TORQUE CONVERTER CONDITION - May cause very low power at breakaway
or high speed (Only 1 condition at a time).
10. FUEL CONTAMINATION - High alcohol or water content.
11. FUEL INJECTORS - Rough idle may be caused by injector wiring not
connected to correct injector.
12. ENGINE SECONDARY IGNITION CHECK - Abnormal scope patterns.
13. TECHNICAL SERVICE BULLETINS - Any that apply to vehicle.
14. All air intake piping and vacuum hoses must be in place and
secure. The proper air filter element must be used.
15. FUEL PRESSURE - Must be correct.
Specification: With no vacuum at the regulator:
48 PSI on V6 & non-turbo 4 Cyl. engines
36 PSI on turbo engines
NS-1: IGNITION CHECK FLOW CHARTS - 2.0L
Fig. 235: NS-1 Flow Chart & Circuit Diagram (2.0L) (1 of 5)
Page 1136 of 1333
determined that all of the engine controls systems are operating as
they were designed to. Therefore, they are not the cause of the
driveability problem. The following additional items should be checked
as possible causes:
1) ENGINE VACUUM - Must be at least 13 inches in neutral.
2) ENGINE VALVE TIMING - Set to specifications.
3) ENGINE COMPRESSION - To specifications.
4) EXHAUST SYSTEM - Free from any restrictions.
5) PCV SYSTEM - Must flow freely.
6) DRIVE SPROCKETS - Camshaft and crank shaft.
7) TORQUE CONVERTER STALL SPEED - To specifications.
8) POWER BRAKE BOOSTER - No internal vacuum leak.
9) FUEL CONTAMINATION - High alcohol and water content.
10) FUEL INJECTORS - Rough idle may be caused by injector
control wire not connected to correct injector.
11) TECHNICAL SERVICE BULLETINS - Any that may apply to
vehicle.
12) ENGINE SECONDARY IGNITION CHECK - Any abnormal scope
pattern.
13) TECHNICAL SERVICE BULLETINS - Any that apply to vehicle.
14) All air intake piping and vacuum hoses must be in place
and secure. The proper air filter element must be used.
15) FUEL PRESSURE - Must be correct.
Specification: With no vacuum at the regulator:
48 PSI on V6 & non-turbo 4 Cyl. engines
36 PSI on turbo engines
DR-VER: DRIVEABILITY VERIFICATION TEST - 2.0L
Fig. 300: DR-VER Flow Chart (2.0L)
SUMMARY
Page 1149 of 1333
\003
TR AIL E R H IT C H W ELD C AN B REA K : N EW T R AIL E R H IT C H
1991 M it s u bis h i M onte ro
NHTSA RECALL BULLETIN
Models: 1986 Isuzu Trooper II
1987 Dodge Raider
1987 Isuzu Trooper II
1988 Dodge Raider
1988 Isuzu Trooper II
1989 Dodge Raider
1989 Isuzu Amigo
1989 Isuzu Trooper II
1990 Isuzu Amigo
1990 Isuzu Trooper
1991 Isuzu Amigo
1991 Isuzu Trooper
1991 Mitsubishi Montero
1991 Toyota Land Cruiser
1992 Mitsubishi Montero
1992 Toyota Land Cruiser
1993 Toyota Land Cruiser
Number of Affected Vehicles: 670
Beginning Date of Manufacture: 1992 MAR
Ending Date of Manufacture: 1993 JUN
FAULT:
Weld, Solder broken
SYSTEM:
Trailer hitch.
EQUIPMENT DESCRIPTION:
Reese class II trailer hitch, Part No. 06070.
DESCRIPTION OF DEFECT:
The weld on the receiver unit of the trailer hitch can break.
CONSEQUENCE OF DEFECT:
If the failure occurs, the trailer can separate from the towing
vehicle, and could result in a vehicle crash without warning.
CORRECTIVE ACTION:
Replace the trailer hitch.
NOTE:
If your vehicle is presented to the dealer from whom you purchased the
item on an agreed service date and the remedy is not provided or the
remedy does correct the safety-related defect or noncompliance, please
contact Reese Products warranty department at 1-800-326-1090, ext.
203. Also contact the National Highway Traffic Safety Administration's
auto safety hotline at 1-800-424-9393.
ADDITIONAL INFORMATION:
The National Highway Traffic Safety Administration operates Monday
Page 1173 of 1333
\003
TR AN SM IS SIO N S ER VIC IN G - A /T
1991 M it s u bis h i M onte ro
1991 TRANSMISSION SERVICING
Automatic Transmission
Mitsubishi: Eclipse, Galant, Mirage,
Montero, Pickup, Precis, 3000GT
IDENTIFICATION
MITSUBISHI AUTOMATIC TRANSMISSION APPLICATIONS \
\
\
\
\
\
Model Transmission/Transaxle
Eclipse
1.8 & 2.0L ........................... Model F4A22 Transaxle
2.0L Turbo ........................... Model F4A33 Transaxle
All-Wheel Drive (AWD) ................ Model W4A33 Transaxle
Galant
AWD .................................. Model W4A32 Transaxle
DOHC ................................. Model F4A22 Transaxle
SOHC ........................ Model KM175 or F4A22 Transaxle
Mirage
1.5L ................................. Model F3A21 Transaxle
1.6L ................................. Model F4A21 Transaxle
Montero ............................ Model V4AW2 Transmission
Pickup ............................. Model R4AC1 Transmission
Precis ................................ Model KM176 Transaxle
3000GT ................................ Model F4A33 Transaxle
\
\
\
\
\
\
LUBRICATION
TRANSAXLE/TRANSMISSION SERVICE INTERVALS
Check fluid level every 12 months or 15,000 miles. Change
fluid and filter every 30,000 miles. If vehicle is operated under
severe condition, change fluid more often. If severe darkening of
fluid and strong odor are noted, bands should also be adjusted (if
equipped).
TRANSFER CASE SERVICE INTERVALS
On 4WD and AWD models, change transfer case fluid every 30,
000 miles.
CHECKING FLUID LEVEL
TRANSAXLE/TRANSMISSION
1) Park vehicle on level area. Ensure oil is at normal
operating temperature, parking brake is engaged, and engine is at
idle. Move gear selector through each position, stopping briefly in
each position.
2) Place gear selector in Neutral, and clean area around
dipstick tube. Ensure fluid level is between lower and upper marks,
but never over upper mark, in HOT range. Add or drain fluid if
necessary.
Page 1178 of 1333
adjusting screw turns freely in lever.
2) Using torque wrench, tighten band adjusting screw to 30
INCH lbs. (3.5 N.m). Back off adjusting screw 6 turns. Hold adjusting
screw in this position, and tighten lock nut to 25 ft. lbs. (34 N.m).
3) Reinstall oil pan using new gasket. Tighten pan bolts to
150 INCH lbs. (17 N.m). Refill with specified transmission fluid.
KICKDOWN SERVO
ECLIPSE, GALANT, MIRAGE, PRECIS & 3000GT
1) Remove all dirt and grease around kickdown servo switch.
Remove snap ring and kickdown servo switch.
2) To prevent servo piston from turning, install Adapter
(MD998915) and Kickdown Servo Wrench (MD998914) so tab of wrench
engages with notch of piston. See Fig. 2.
CAUTION: DO NOT push servo piston inward while installing adapter
and servo wrench. Install adapter in brake pressure port by
hand ONLY. DO NOT use wrench to tighten adapter.
Fig. 2: Adjusting Kickdown Servo (Except Montero & Pickup)
Courtesy of Mitsubishi Motor Sales of America.
3) Loosen lock nut to "V" channel of adjuster rod. See
Fig. 2 . Tighten inner section of Kickdown Service Adjustment Assembly
(MD998916) until it contacts lock nut.
4) Install outer section of kickdown service adjustment
assembly on lock nut. Rotate outer section to left and inner section
to right to contact lock nut with inner section.
5) Using an INCH lb. torque wrench on inner section, tighten
inner section to 86 INCH lbs. (9.8 N.m), and then loosen inner
section. Tighten inner section to 43 INCH lbs. (4.9 N.m).
CAUTION: Before tightening lock nut with torque wrench, tighten it
by hand until it contacts piston. If torque wrench is used
Page 1185 of 1333
\003TR AN SM IS SIO N S ER VIC IN G - M /T
1991 M it s u bis h i M onte ro
1990-91 Manual Transmission Servicing
Eclipse, Galant, Mirage, Montero, Pickup, Precis, Sigma
IDENTIFICATION
1990 MANUAL TRANSMISSION APPLICATIONS TABLE \
\
\
\
\
Model Transmission
Eclipse
1.8L SOHC ..... 5-Speed - Model F5M22 Transaxle
1.8L DOHC ..... 5-Speed - Model F5M22 Transaxle
2.0L DOHC
Turbo ........ 5-Speed - Model F5M33 Transaxle
Galant ......... 5-Speed - Model KM206 Transaxle
Mirage
1.5L ......... 5-Speed - Model KM201 Transaxle
1.6L ......... 5-Speed - Model KM210 Transaxle
Montero
2.6L ................... 5-Speed - Model KM145
3.0L ................... 5-Speed - Model V5MT1
Pickup
2WD .................... 5-Speed - Model KM132
4WD .................... 5-Speed - Model KM145
Precis ......... 4-Speed - Model KM161 Transaxle
5-Speed - Model KM163 Transaxle
Sigma .......... 5-Speed - Model KM210 Transaxle
\
\
\
\
\
1991 MANUAL TRANSMISSION APPLICATIONS TABLE \
\
\
\
\
Model Transmission
Eclipse
2.0L ............... 5-Speed Transaxle (F5M22)
2.0L (Turbo) ....... 5-Speed Transaxle (F5M33)
Galant
2WD ................ 5-Speed Transaxle (F5M22)
AWD
DOHC ............. 5-Speed Transaxle (W5M31)
DOHC (Turbo) ..... 5-Speed Transaxle (W5M33)
Mirage
1.5L ............... 4-Speed Transaxle (F4M21)
5-Speed Transaxle (F5M21)
1.6L ............... 5-Speed Transaxle (F5M22)
Montero ........... 5-Speed Transmission (V5MT1)
Pickup
2WD ............. 5-Speed Transmission (R5M21)
4WD ............. 5-Speed Transmission (V5MT1)
Precis ............... 4-Speed Transaxle (KM200)
5-Speed Transaxle (KM201)
3000GT
2WD ................ 5-Speed Transaxle (F5M33)
AWD ................ 5-Speed Transaxle (W5MG1)
\
\
\
\
\
LUBRICATION SERVICE INTERVALS
Page 1186 of 1333
Check transaxle/transmission and transfer case fluid level
every 30,000 miles. Change fluid at 30,000 miles if operated under
severe service conditions.
CHECKING FLUID LEVEL
TRANSAXLE/TRANSMISSION
Lubricant level is checked at fill hole on side of transaxle
or transmission. Lubricant must be at bottom of fill hole.
TRANSFER CASE
Transfer case contains separate drain and fill plugs.
Lubricant must reach to bottom of fill hole.
On 3000GT models, transfer case contains separate drain and
fill plugs. Lubricant should be .5" (13 mm) from bottom of fill hole.
RECOMMENDED FLUID
Use API GL-4 or GL-5 SAE 75W-85 gear oil.
FLUID CAPACITY SPECS TABLE
TRANSMISSION REFILL CAPACITIES TABLE \
\
\
\
\
Application Pts. (L)
Eclipse
F5M22 .............................. 3.8 (1.8)
F5M33 .............................. 4.7 (2.2)
Galant ............................... 3.8 (1.8)
Mirage
KM201 .............................. 3.8 (1.8)
KM210 .............................. 4.4 (2.0)
Montero
2.6L ............................... 4.7 (2.2)
3.0L ............................... 5.3 (2.6)
Pickup
2WD ................................ 4.9 (2.4)
4WD ................................ 4.7 (2.2)
Precis ............................... 4.4 (2.0)
Sigma ................................ 5.2 (2.5)
\
\
\
\
\
1991 TRANSMISSION REFILL CAPACITIES \
\
\
\
\
\
Application Pts. (L)
Mirage (1.5L)
F4M21 ................................... 3.6 (1.7)
F5M21 ................................... 3.8 (1.8)
Eclipse, Galant (2WD) & Mirage (1.6L) ..... 3.8 (1.8)
Eclipse (Turbo) & 3000GT (2WD) ............ 4.9 (2.3)
Galant (AWD) .............................. 4.9 (2.3)
Montero & Pickup .......................... 5.2 (2.5)
Pickup .................................... 4.9 (2.3)
Pickup .................................... 4.6 (2.2)
Precis
Page 1240 of 1333
knuckles steering linkage
Rack and pinion mounting Tighten all mounting
loose bolts
Rack and pinion out of See adjustment in
adjustment STEERING article
Tie rod end loose Tighten and check
steering linkage
Excessive Pitman shaft-to- Repair as necessary
ball nut lash
\
\
\
\
\
\
\
Poor Lack of lubricant in ball Lubricate and service
Returnability joint or linkage systems
Binding in linkage or ball See STEERING LINKAGE
joints and SUSPENSION article
Improper front end alignment See WHEEL ALIGNMENT
article
Improper tire pressure Inflate to proper
pressure
Tie rod binding Inflate to proper
pressure
Shaft seal rubbing shaft See STEERING COLUMN
article
\
\
\
\
\
\
\
Excessive Improper tire pressure Inflate to proper
Vertical Motion pressure
Tires, wheels or rotors Balance tires then
out of balance check wheels and
rotors
Worn or faulty shock Check and replace if
absorbers necessary
Loose tie rod ends or Tighten or replace if
steering necessary
Loose or worn wheel See SUSPENSION article
bearings
\
\
\
\
\
\
\
Steering Pulls Improper tire pressure Inflate to proper
to One Side pressure
Front tires are different Rotate or replace if
sizes necessary
Wheel bearings not See FRONT SUSPENSION
article
adjusted properly
Bent or broken suspension See FRONT SUSPENSION
components article
Improper wheel alignment See WHEEL ALIGNMENT
article
Page 1244 of 1333
Reaction ring sticking See POWER STEERING GEAR
in housing head article
Steering pump internal See POWER STEERING PUMP
leakage article
Steering gear-to-column See STEERING COLUMN
misalignment article
Lack of lubrication in Service front suspension
linkage
Lack of lubrication in Service front suspension
ball joints
\
\
\
\
\
\
\
Increased Effort High internal pump leakage See POWER STEERING PUMP
When Turning article
Wheel Fast Power steering pump belt Adjust or replace if
Foaming, Milky slipping necessary
Power Steering
Fluid, Low Fluid Low fluid level Check and fill to
Level or Low proper level
Pressure
Engine idle speed to low Adjust to correct
setting
Air in pump fluid system See POWER STEERING PUMP
article
Pump output low See POWER STEERING PUMP
article
Steering gear See POWER STEERING GEAR
malfunctioning article
\
\
\
\
\
\
\
Wheel Surges Low fluid level Check and fill to proper
or Jerks level
Loose fan belt Adjust or replace if
necessary
Insufficient pump See POWER STEERING PUMP
pressure article
Sticky flow control valve See POWER STEERING PUMP
article
Linkage hitting oil pan Replace bent components
at full turn
\
\
\
\
\
\
\
Kick Back or Air in pump fluid system See POWER STEERING PUMP
Free Play article
Worn poppet valve in See POWER STEERING PUMP
steering gear article
Excessive over center See POWER STEERING GEAR
lash article
Thrust bearing out of See POWER STEERING GEAR
adjustment article
Page 1309 of 1333
subtracted by the width measured at the front of the tires at about
spindle height. A positive figure would indicate toe-in and a negative
figure would indicate toe-out. If the distance between the front and
rear of the tires is the same, toe measurement would be zero. To
adjust:
1) Measure toe-in with front wheels in straight ahead
position and steering wheel centered. To adjust toe-in, loosen clamps
and turn adjusting sleeve or adjustable end on right and left tie
rods. See Figs. 2 and 5.
2) Turn equally and in opposite directions to maintain
steering wheel in centered position. Face of tie rod end must be
parallel with machined surface of steering rod end to prevent binding.
3) When tightening clamps, make certain that clamp bolts are
positioned so there will be no interference with other parts
throughout the entire travel of linkage.
Fig. 5: Wheel Toe-In (Dimension A Less Dimension B)
TOE-OUT ON TURNS
1) Toe-out on turns (turning radius) is a check for bent or
damaged parts, and not a service adjustment. With caster, camber, and
toe-in properly adjusted, check toe-out with weight of vehicle on
wheels.
2) Use a full floating turntable under each wheel, repeating
test with each wheel positioned for right and left turns. Incorrect
toe-out generally indicates a bent steering arm. Replace arm, if
necessary, and recheck wheel alignment.