air condition MITSUBISHI MONTERO 1991 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 1194 of 1333
![MITSUBISHI MONTERO 1991 Service Manual \
OK NOT OK
\b](/img/19/57332/w960_57332-1193.png "MITSUBISHI MONTERO 1991 Service Manual \
OK NOT OK
\b")
\
OK NOT OK
\b \b
\
\
\
\
\
\
* Check Pick-Up coil for * Adjust or replace as
correct resistance value. necessary.
\
\
\
\b
\
\
\
\b
\
\
\
\
NOT OK OK
\b \b
\
\
\
\
\
\
* Replace Pick-Up coil if * Check control module for
not to specification. good ground connections.
\
\
\
\b
\
\
\
\b
OK
\b
\
\
\
\
\
* If vehicle fails to run at this point, go to
the appropriate article in the ENGINE
PERFORMANCE section.
\
\
\
\
\
\b
\
\
\
\b
\
\
\
\
\
OK NOT OK
\b \b
\
\
\
\
\
\
* Check wires from the battery/ * Replace ballast resistor
ignition switch to the coil. if the measured resistance
Also check the coil primary value is not within
and secondary resistance. specification.
\
\
\
\b
\
\
\
\b
STARTER TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC STARTER TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Starter Fails Dead battery or bad Check battery charge
to Operate connections between and all wires and
starter and battery connections to starter
Ignition switch faulty Adjust or replace
or misadjusted ignition switch
Open circuit between Check and repair wires
starter switch ignition and connections as
terminal on starter relay necessary
Starter relay or starter See Testing in STARTER
defective article
Page 1198 of 1333
![MITSUBISHI MONTERO 1991 Service Manual Fires With Key Flywheel runout contributes
released. Engine to the intermittent nature
Fires and Cranks
Normally
\
\
\
\](/img/19/57332/w960_57332-1197.png "MITSUBISHI MONTERO 1991 Service Manual Fires With Key Flywheel runout contributes
released. Engine to the intermittent nature
Fires and Cranks
Normally
\
\
\
\")
Fires With Key Flywheel runout contributes
released. Engine to the intermittent nature
Fires and Cranks
Normally
\
\
\
\
\
\
\
AIR CONDITIONING & HEAT
AIR CONDITIONING TROUBLE SHOOTING
WARNING: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC AIR CONDITIONING TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE \
\
\
\
\
\
\
Compressor Not Working
Compressor clutch circuit open.
Compressor clutch coil inoperative.
Poor clutch ground connection.
Fan belts loose.
Thermostatic switch inoperative.
Thermostatic switch not adjusted.
Ambient temperature switch open.
Superheat fuse blown. \
\
\
\
\
\
\
Excessive Noise or Vibration
Missing or loose mounting bolts.
Bad idler pulley bearings.
Fan belts not tightened correctly.
Compressor clutch contacting body.
Excessive system pressure.
Compressor oil level low.
Damaged clutch bearings.
Damaged reed valves.
Damaged compressor. \
\
\
\
\
\
\
Insufficient or No Cooling;
Compressor Working
Expansion valve inoperative.
Heater control valve stuck open.
Low system pressure.
Blocked condenser fins.
Blocked evaporator fins.
Vacuum system leak.
Vacuum motors inoperative.
Control cables improperly adjusted.
Restricted air inlet.
Mode doors binding.
Blower motor inoperative.
Temperature above system capacity. \
\
\
\
\
\
\
HEATER SYSTEM TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
Page 1199 of 1333
problem symptoms. For model-specific Trouble Shooting,
refer to DIAGNOSTIC, or TESTING articles available in the
section(s) you are accessing.
BASIC HEATER SYSTEM TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE \
\
\
\
\
\
\
Insufficient, Erratic,
or No Heat
Low Coolant Level
Incorrect thermostat.
Restricted coolant flow through
heater core.
Heater hoses plugged.
Misadjusted control cable.
Sticking heater control valve.
Vacuum hose leaking.
Vacuum hose blocked.
Vacuum motors inoperative.
Blocked air inlet.
Inoperative heater blower motor.
Oil residue on heater core fins.
Dirt on heater core fins. \
\
\
\
\
\
\
Too Much Heat
Improperly adjusted cables.
Sticking heater control valve.
No vacuum to heater control valve.
Temperature door stuck open. \
\
\
\
\
\
\
Air Flow Changes During
Acceleration
Vacuum system leak.
Bad check valve or reservoir. \
\
\
\
\
\
\
Air From Defroster At All
Times
Vacuum system leak.
Improperly adjusted control cables.
Inoperative vacuum motor. \
\
\
\
\
\
\
Blower Does Not Operate
Correctly
Blown fuse.
Blower motor windings open.
Resistors burned out.
Motor ground connection loose.
Wiring harness connections loose.
Blower motor switch inoperative.
Blower relay inoperative.
Fan binding or foreign object
in housing.
Fan blades broken or bent. \
\
\
\
\
\
\
BRAKES
BRAKE SYSTEM TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
Page 1204 of 1333
![MITSUBISHI MONTERO 1991 Service Manual in the section(s) you are accessing.
BASIC GASOLINE ENGINE - MECHANICAL TROUBLE SHOOTING CHART
\
\
\
\](/img/19/57332/w960_57332-1203.png "MITSUBISHI MONTERO 1991 Service Manual in the section(s) you are accessing.
BASIC GASOLINE ENGINE - MECHANICAL TROUBLE SHOOTING CHART
\
\
\
\")
in the section(s) you are accessing.
BASIC GASOLINE ENGINE - MECHANICAL TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Engine Lopes At Intake manifold-to-head Replace manifold
Idle leaks gasket, See ENGINES
Blown head gasket Replace head gasket,
See ENGINES
Worn timing gears, chain Replace gears, chain or
or sprocket sprocket
Worn camshaft lobes Replace camshaft, See
ENGINES
Overheated engine Check cooling system,
See COOLING
Blocked crankcase vent Remove restriction
valve
Leaking EGR valve Repair leak and/or
replace valve
Faulty fuel pump Replace fuel pump
\
\
\
\
\
\
\
Engine Has Low Leaking fuel pump Repair leak and/or
Power replace fuel pump
Excessive piston-to-bore Install larger pistons,
clearance See ENGINES
Sticking valves or weak Check valve train
valve springs components, See ENGINES
Incorrect valve timing Reset valve timing, See
ENGINES
Worn camshaft lobes Replace camshaft, See
ENGINES
Blown head gasket Replace head gasket.
See ENGINES.
Clutch slipping Adjust pedal and/or
replace components, See
ENGINES
Engine overheating Check cooling system,
See COOLING
Auto. Trans. pressure
regulator valve faulty Replace pressure
regulator valve
Auto. Trans. fluid level Add fluid as necessary
too low
Improper vacuum diverter
valve operation Replace vacuum diverter
valve
Vacuum leaks Inspect vacuum system
and repair as required
Leaking piston rings Replace piston rings,
See ENGINES
\
\
\
\
\
\
\
Faulty High Low fuel pump volume Replace fuel pump
Speed Operation
Leaking valves or worn Replace valves and/or
springs, See ENGINES
Incorrect valve timing Reset valve timing,See
ENGINES
Intake manifold restricted Remove restriction
Worn distributor shaft Replace distributor
\
\
\
\
\
\
\
Faulty Improper fuel pump stroke Remove pump and reset
Acceleration pump stroke
Page 1209 of 1333
![MITSUBISHI MONTERO 1991 Service Manual cracked or broken manifold, See ENGINES \
\
\
\
\
\](/img/19/57332/w960_57332-1208.png "MITSUBISHI MONTERO 1991 Service Manual cracked or broken manifold, See ENGINES \
\
\
\
\
\")
cracked or broken manifold, See ENGINES \
\
\
\
\
\
\
ENGINE PERFORMANCE
CARBURETOR TROUBLE SHOOTING:
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC COLD START SYMPTOMS TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Engine Won't Choke not closing Check choke
Start operation, see
FUEL SYSTEMS
Choke linkage bent Check linkage, see
FUEL SYSTEM
\
\
\
\
\
\
\
Engine Starts, Choke vacuum kick setting Check setting and
Then Dies too wide adjust see, FUEL
SYSTEMS
Fast idle RPM too low Reset RPM to specif-
ication, see TUNE-UP
Fast idle cam index Reset fast idle cam
incorrect index, see FUEL
SYSTEMS
Vacuum leak Inspect vacuum
system for leaks
Low fuel pump outlet Repair or replace
pump, see FUEL
SYSTEMS
Low carburetor fuel level Check float setting
see FUEL SYSTEM
\
\
\
\
\
\
\
Engine Quits Choke vacuum kick setting Reset vacuum kick
Under Load incorrect setting,see FUEL
SYSTEMS
Fast idle cam index Reset fast idle cam
incorrect index, see FUEL
SYSTEM
Incorrect hot fast idle Reset fast idle RPM,
speed RPM see TUNE-UP
\
\
\
\
\
\
\
Engine Starts, Choke vacuum kick set too Reset vacuum kick,
Runs Up,Then narrow see FUEL SYSTEMS
Idles, Slowly
With Black Smoke Fast idle cam index Reset fast idle cam
Page 1210 of 1333
incorrect index, see FUEL
SYSTEMS
Hot fast idle RPM too low Reset fast idle RPM,
see TUNE-UP
\
\
\
\
\
\
\
BASIC HOT START SYMPTOMS TROUBLE SHOOTING CHART \
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Engine Won't Engine flooded Allow fuel to
Start evaporate
\
\
\
\
\
\
\
BASIC COLD ENGINE DRIVEABILITY SYMPTOMS TROUBLE SHOOTING CHART \
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Engine Stalls in Choke vacuum kick setting Reset choke vacuum
Gear incorrect kick, see FUEL
SYSTEMS
Fast idle RPM incorrect Reset fast idle RPM,
see TUNE-UP
Fast idle cam index Reset fast idle cam
incorrect see FUEL SYSTEMS
\
\
\
\
\
\
\
Acceleration Sag Defective choke control Replace choke
or Stall switch control switch
Choke vacuum kick setting Reset choke vacuum
incorrect kick see, FUEL
SYSTEMS
Float level incorrect Adjust float level,
(too low) FUEL SYSTEMS
Accelerator pump defective Repair or replace
pump see FUEL
SYSTEMS
Secondary throttles not Inspect lockout
closed adjustment,see FUEL
SYSTEMS
\
\
\
\
\
\
\
Sag or Stall Defective choke control Replace choke
After Warmup switch control switch, see
FUEL SYSTEMS
Defective accelerator pump Replace pump, see
FUEL SYSTEMS
Float level incorrect Adjust float level,
(too low) see FUEL SYSTEMS
\
\
\
\
\
\
\
Backfiring & Plugged heat crossover Remove restriction
Black Smoke system
\
\
\
\
\
\
\
BASIC WARM ENGINE DRIVEABILITY SYMPTOMS TROUBLE SHOOTING CHART \
\
\
\
\
\
\
Page 1211 of 1333
![MITSUBISHI MONTERO 1991 Service Manual CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\](/img/19/57332/w960_57332-1210.png "MITSUBISHI MONTERO 1991 Service Manual CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\")
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Hesitation With Vacuum leak Inspect vacuum lines
Small Amount of
Gas Pedal Movement
Accelerator pump weak or Replace pump, see
inoperable FUEL SYSTEMS
Float level setting too low Reset float level,
see,FUEL SYSTEMS
Metering rods sticking or Inspect and/or
binding replace rods, see
FUEL SYSTEMS
Carburetor idle or transfer Inspect system and
system plugged remove restriction
Frozen or binding heated air Inspect heated air
inlet door for binding
\
\
\
\
\
\
\
Hesitation With Defective accelerator pump Replace pump, see
Heavy Gas Pedal FUEL SYSTEMS
Movement
Metering rod carrier Remove restriction
sticking or binding
Large vacuum leak Inspect vacuum
system and repair
leak
Float level setting too Reset float level,
low see FUEL SYSTEMS
Defective fuel pump, lines Inspect pump, lines
or filter and filter
Air door setting incorrect Adjust air door
setting, see FUEL
\
\
\
\
\
\
\
DIESEL ENGINE TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
NOTE: Diesel engines mechanical diagnosis is the same as gasoline
engines for items such as noisy valves, bearings, pistons,
etc. The following trouble shooting covers only items
pertaining to diesel engines.
BASIC DIESEL ENGINE TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Engine Won't Bad battery connections Check connections
Crank or dead batteries and/or replace
Page 1214 of 1333
![MITSUBISHI MONTERO 1991 Service Manual Incorrect injector pump Check pressure, see
housing pressure FUEL SYSTEMS
\
\
\](/img/19/57332/w960_57332-1213.png "MITSUBISHI MONTERO 1991 Service Manual Incorrect injector pump Check pressure, see
housing pressure FUEL SYSTEMS
\
\
\")
Incorrect injector pump Check pressure, see
housing pressure FUEL SYSTEMS
\
\
\
\
\
\
\
Engine Cooling system leaks Check cooling system
Overheating and repair leaks
Belt slipping or damaged Check tension and/or
replace belt
Thermostat stuck closed Remove and replace
thermostat, see
ENGINE COOLING
Head gasket leaking Replace head gasket
\
\
\
\
\
\
\
Oil Light on at Low oil pump pressure Check oil pump
Idle operation, see ENGINES
Oil cooler or line Remove restriction
restricted and/or replace cooler
\
\
\
\
\
\
\
Engine Won't Injector pump fuel solenoid Remove and check
Shut Off does not return fuel valve solenoid and replace
to OFF position if needed
\
\
\
\
\
\
\
VACUUM PUMP DIAGNOSIS
Excessive Noise Loose pump-to-drive Tighten screws
assembly screws
Loose tube on pump assembly Tighten tube
Valves not functioning Replace valves
properly
Oil Leakage Loose end plug Tighten end plug
Bad seal crimp Remove and re-crimp
seal
\
\
\
\
\
\
\
FUEL INJECTION TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC FUEL INJECTION TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Engine Won't Cold start valve inoperative Test valve and
Start (Cranks circuit
Normally)
Poor connection;vacuum or Check vacuum and
wiring electrical
connections
Contaminated fuel Test fuel for water
or alcohol
Defective fuel pump relay Test relay and
or circuit wiring
Battery too low Charge and test
battery
Page 1218 of 1333
![MITSUBISHI MONTERO 1991 Service Manual \
\
\
\
\
\
O](/img/19/57332/w960_57332-1217.png "MITSUBISHI MONTERO 1991 Service Manual \
\
\
\
\
\
O")
\
\
\
\
\
\
OK NOT OK
\b \b
\
\
\
\
\
\
* Check air Gap of the Pick-Up * Check resistance of ballast
coil in the distributor. resistor (if used) for the
\
\
\
\b
correct resistance value.
\
\
\
\b
\
\
\
\
OK NOT OK
\b \b
\
\
\
\
\
\
* Check Pick-Up coil for * Adjust or replace as
correct resistance value. necessary.
\
\
\
\b
\
\
\
\b
\
\
\
\
NOT OK OK
\b \b
\
\
\
\
\
\
* Replace Pick-Up coil if * Check control module for
not to specification. good ground connections.
\
\
\
\b
\
\
\
\b
OK
\b
\
\
\
\
\
* If vehicle fails to run at this point, go to
the appropriate article in the ENGINE
PERFORMANCE section.
\
\
\
\
\
\b
\
\
\
\b
\
\
\
\
\
OK NOT OK
\b \b
\
\
\
\
\
\
* Check wires from the battery/ * Replace ballast resistor
ignition switch to the coil. if the measured resistance
Also check the coil primary value is not within
and secondary resistance. specification.
\
\
\
\b
\
\
\
\b
STARTER TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC STARTER TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Starter Fails Dead battery or bad Check battery charge
to Operate connections between and all wires and
starter and battery connections to starter
Page 1222 of 1333
![MITSUBISHI MONTERO 1991 Service Manual \
\
\
\
\
\
\
High Pitched Whine Distance too great](/img/19/57332/w960_57332-1221.png "MITSUBISHI MONTERO 1991 Service Manual \
\
\
\
\
\
\
High Pitched Whine Distance too great")
\
\
\
\
\
\
\
High Pitched Whine Distance too great Align starter or check
During Cranking between starter that correct starter
Before Engine pinion and flywheel and flywheel are being
Fires but Engine used
Fires and Cranks
Normally
\
\
\
\
\
\
\
High Pitched Distance too small between
Whine After Engine starter pinion and flywheel
Fires With Key Flywheel runout contributes
released. Engine to the intermittent nature
Fires and Cranks
Normally
\
\
\
\
\
\
\
TUNE-UP TROUBLE SHOOTING - GAS ENGINE VEHICLES
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC SPARK PLUG TROUBLE SHOOTING CHARTS
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Normal Spark Light Tan or Gray deposits No Action
Plug Condition
Electrode not burned or No Action
fouled
Gap tolerance not changed No Action
\
\
\
\
\
\
\
Cold Fouling or Overrich air/fuel mixture Adjust air/fuel
Carbon Deposits mixture, see ENGINE
PERFORMANCE section
Faulty choke Replace choke
assembly, see ENGINE
PERFORMANCE section
Clogged air filter Clean and/or replace
air filter
Incorrect idle speed or Reset idle speed and/
dirty carburetor or clean carburetor
Faulty ignition wires Replace ignition
wiring
Prolonged operation Shut engine off
at idle during long idle
Sticking valves or worn Check valve train
valve guide seals
\
\
\
\
\
\
\
Wet Fouling Worn rings and pistons Install new rings and
or Oil Deposits pistons