ignition MITSUBISHI MONTERO 1991 Repair Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 670 of 1333
2.6L Engine ........................................... 45
2.6L Optional ......................................... 45
3.0L V6 ........................................... (1) 24
3.5L V6 ........................................... ( 1) 24
( 1) - Check hood clearance on 1986 and newer models.
\
\
\
\
\
\
CAUTIONS & WARNINGS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG SYSTEM
NOTE: See the AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT Section.
The SRS has no user-servicable parts. Always have servicing
done by an authorized dealer.
When performing maintenance on air bag equipped vehicles
always observe proper safety precautions.
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all warnings and service precautions. See
appropriate AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT section.
CAUTION: Disconnect negative battery cable before servicing any air
bag system, steering column or passenger side dash
component. After any repair, turn ignition key to the ON
position from passenger's side of vehicle in case of
accidental air bag inflation
ANTI-LOCK BRAKE SYSTEM (ABS)
CAUTION: Never mix different diameter tires. On loose or uneven
surfaces, the ABS system may require longer stopping
distances than conventional brake systems. Exercise caution
when removing mud or snow from the wheels so as not to
damage the ABS wiring or speed sensors.
BATTERY WARNING
WARNING: When battery is disconnected, vehicles equipped with
computers may lose memory data. When battery power is
restored, driveability problems may exist on some vehicles.
These vehicles may require a relearn procedure. See
appropriate COMPUTER RELEARN PROCEDURES article in the
GENERAL INFORMATION section below.
REPLACING BLOWN FUSES
Before replacing a blown fuse, remove ignition key, turn off
all lights and accessories to avoid damaging the electrical system. Be
sure to use fuse with the correct indicated amperage rating. The use
of an incorrect amperage rating fuse may result in a dangerous
electrical system overload.
BRAKE PAD WEAR INDICATOR
Indicator will cause a squealing or scraping noise, warning
that brake pads need replacement.
Page 671 of 1333
CATALYTIC CONVERTER
Continued operation of vehicle with a severe malfunction
could cause converter to overheat, resulting in possible damage to
converter and vehicle.
COOLANT (PROPYLENE-GLYCOL FORMULATIONS)
CAUTION: To avoid possible damage to vehicle use only ethylene-glycol
based coolants with a mixture ratio from 44-68% anti-freeze.
DO NOT use 100% anti-freeze as it will cause the formation
of cooling system deposits. This results in coolant
temperatures of over 300
\b F (149\bC) which can melt plastics.
100% anti-freeze has a freeze point of only -8\b F (-22\bC).
CAUTION: Propylene-Glycol Mixtures has a smaller temperature range
than Ethylene-Glycol. The temperature range (freeze-boil)
of a 50/50 Anti-Freeze/Water Mix is as follows:
Propylene-Glycol -26
\b F (-32\bC) - 257\b F (125\bC)
Ethylene-Glycol -35\b F (-37\bC) - 263\b F (128\bC)
CAUTION: Propylene-Glycol/Ethylene-Glycol Mixtures can cause the
destabilization of various corrosion inhibitors. Also
Propylene-Glycol/Ethylene-Glycol has a different specific
gravity than Ethylene-Glycol coolant, which will result in
inaccurate freeze point calculations.
ELECTROSTATIC DISCHARGE SENSITIVE (ESD) PARTS
WARNING: Many solid state electrical components can be damaged by
static electricity (ESD). Some will display a warning label,
but many will not. Discharge personal static electricity by
touching a metal ground point on the vehicle prior to
servicing any ESD sensitive component.
ENGINE OIL
CAUTION: Never use non-detergent or straight mineral oil.
FUEL SYSTEM SERVICE
WARNING: Relieve fuel system pressure prior to servicing any fuel
system component (fuel injection models).
HALOGEN BULBS
WARNING: Halogen bulbs contain pressurized gas which may explode if
overheated. DO NOT touch glass portion of bulb with bare
hands. Eye protection should be worn when handling or working
around halogen bulbs.
RADIATOR CAP
CAUTION: Always disconnect the fan motor when working near the
radiator fan. The fan is temperature controlled and could
start at any time even when the ignition key is in the OFF
position. DO NOT loosen or remove radiator cap when cooling
system is hot.
RADIATOR FAN
Page 675 of 1333
1 - 20 Amp
Not Used
2 - Not Used
10 Amp (1994-96)
ELC-4 A/T Control Module, Cruise Control Unit
3 - 10 Amp
Blower Motor Relay, Headlight Washer Relay, Defogger Relay,
Car Telephone (1992-93)
4 - 10 Amp
Radio Clock, Accessory Socket Relay,
Cruise Control Unit (1994-96), Data Link Connector (1994-96)\
5 - 15 Amp
Remote Controlled Mirror, Cigarette Lighter
Accessory Socket Relay (1992-93)
6 - 15 Amp
Door Lock Relay, Door Lock Control Unit (1994-96)
7 - 10 Amp
Overdrive Relay, Variable Shock Absorber Control Unit,
4WD Indicator Control Unit, ABS Power Relay (1992-93),
ABS Control Unit (1994-96), Combination Meter (1994-96)
8 - 10 Amp
Power Window Relay
9 - 15 Amp
Wiper, Washer, Sunroof
10 - 10 Amp
Horn, Cruise Control Unit (1992-93)
11 - 10 Amp
Combination Meter, Multi-meter, Motor Antenna Control Unit,
Buzzer Assembly
12 - 15 Amp
Turn Signal Light, Hazard Light, SRS Diagnosis Unit
13 - 10 Amp
Not Used
14 - 15 Amp
Accessory Socket
15 - Not Used
16 - 25 Amp
Blower Motor
17 - 15 Amp
Stoplight
18 - 10 Amp
Back-up Light, Rear Differential Lock Control Unit
19 - 10 Amp
Engine Control Module, Dome Light, Reading Light,
Cargo Light, Combination Meter, Clock, Door Lock Relay,
Cruise Control Unit, Car Telephone (1992-93)
ELC-4 A/T Control Module (1994-96), Ignition Key Illumination\
Light Timer (1994-96)
Page 685 of 1333
\003
N - R EM OVE/IN STA LL/O VER HAU L
1991 Mitsubishi Montero
1991 ENGINE PERFORMANCE
Removal, Overhaul & Installation
Dodge; Colt, Colt 200, Colt Vista, Ram-50, Stealth
Eagle; Summit
Mitsubishi; Eclipse, Galant, Mirage, Montero, Pickup, 3000GT
Plymouth; Colt, Colt 200, Colt Vista
INTRODUCTION
Removal, overhaul and installation procedures (when given by
manufacturer) are covered in this article. If component removal and
installation is primarily an unbolt and bolt-on procedure, only a
torque specification may be furnished.
IGNITION SYSTEM
DISTRIBUTOR
Fig. 1: Exploded View of Distributor (Colt Vista)
Courtesy of Mitsubishi Motor Sales of America.
Page 689 of 1333
FUEL SYSTEM PRESSURE RELEASE
WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel
injection-related component. DO NOT allow fuel to contact
engine or electrical components.
1) On Colt and Mirage, remove rear seat cushion. On all
models, disconnect fuel pump harness connector at fuel tank.
2) Start engine. Let engine run until it stops. Turn ignition
off. Disconnect negative battery terminal. Connect fuel pump harness
connector.
FUEL PUMP
Removal & Installation
1) Fuel pump assembly is located inside fuel tank. Release
fuel pressure from system. See FUEL SYSTEM PRESSURE RELEASE. Raise
vehicle on hoist. Drain fuel into suitable container. Disconnect
electrical connectors and fuel hoses at fuel tank.
2) Remove fuel filler hose from fuel tank. Remove nuts
securing fuel tank. Remove fuel tank from vehicle and remove fuel pump
assembly. To install, reverse removal procedure. Tighten nuts to
specification. See TORQUE SPECIFICATION table.
FUEL RAILS & INJECTORS (PFI)
Use a rag to cover fuel hose connection before disconnecting
high pressure fuel hose at fuel rail. Some residual fuel pressure may
still be in system.
Removal (Except Pickup & Ram-50 2.4L)
1) On all models, relieve fuel pressure. See
FUEL SYSTEM PRESSURE RELEASE . Disconnect negative battery cable. On
Montero, Pickup, Ram-50, Stealth and 3000GT 3.0L, disconnect air
intake plenum. On Eclipse, disconnect PCV valve hose.
2) On Colt Vista, disconnect coolant temperature sensor
connector, idle speed control servo connector and brake booster vacuum
hose. On all models, disconnect high pressure fuel hose at fuel rail.
3) Disconnect fuel return hose. Disconnect vacuum hoses. On
Eclipse, Colt and Colt 200, disconnect throttle cable clamp. Remove
center cover. On all models, disconnect injector electrical
connectors. Remove fuel rail bolts and lift fuel rail and injectors
from engine.
Installation
To install, reverse removal procedure. Tighten bolts to
specifications. See TORQUE SPECIFICATIONS table.
Removal (Pickup & Ram-50 2.4L)
1) Relieve fuel pressure. See FUEL SYSTEM PRESSURE RELEASE.
Disconnect negative battery cable. Drain coolant. On all models,
disconnect air intake hose. Disconnect breather hose (if applicable)
and vacuum hoses.
2) Disconnect coolant lines as necessary for clearance.
Disconnect injector electrical connectors. Position all lines, hoses
and electrical connectors out of way. Disconnect throttle and/or
kickdown cables. Remove throttle body assembly and position it out of
the way.
3) Disconnect high pressure fuel hose at fuel rail.
Disconnect fuel return line and vacuum line connection at fuel rail.
Remove fuel rail bolts and lift fuel rail and injectors from engine.
Page 696 of 1333
SC HED ULE D S ER VIC ES
1991 Mitsubishi Montero
1987-95 MAINTENANCE
Mitsubishi Maintenance & Service Intervals
Montero
* PLEASE READ THIS FIRST *
NOTE: All SERVICE SCHEDULES are listed for normal service
vehicles. If vehicle is operated under severe service
conditions, see
SEVERE SERVICE REQUIREMENTS (PERFORM W/SERVICE SCHEDULES)
for items requiring additional maintenance.
NOTE: This article contains scheduled maintenance service
information. Fluid types and capacities listed with each
service in this article are only those necessary to perform
that scheduled service. For specifications pertaining to
fluid capacities for the entire vehicle, fuse and circuit
breaker identification, wheel and tire size, battery type,
warranty information, or model identification refer to the
MAINTENANCE INFORMATION article in this section.
CAUTIONS & WARNINGS
SUPPLEMENTAL RESTRAINT SYSTEM (AIR BAG)
NOTE: See the AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT Section.
Modifications or improper maintenance, including incorrect
removal and installation of the Supplemental Restraint System (SRS),
can adversely affect system performance. DO NOT cover, obstruct or
change the steering wheel horn pad in any way, as such action could
cause improper function of the system. Use only plain water when
cleaning the horn pad. Solvents or cleaners could adversely affect the
air bag cover and cause improper deployment of the system.
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all warnings and service precautions. See
appropriate AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT section.
CAUTION: Disconnect negative battery cable before servicing any air
bag system, steering column or passenger side dash
component. After any repair, turn ignition key to the ON
position from passenger's side of vehicle in case of
accidental air bag inflation
AIR CONDITIONING SERVICING
WARNING: R-134a service equipment or vehicle A/C systems SHOULD NOT
be pressure tested or leak tested with compressed air. Some
mixtures of air/R134a have shown to be combustible at
elevated pressures. These mixtures are dangerous and may
cause fire and/or explosions. See the appropriate
A/C SYSTEM GENERAL SERVICING article in the AIR CONDITIONING
& HEAT section.
Page 697 of 1333
WARNING: Avoid breathing R-134a refrigerant and PAG lubricant vapors,
exposure may irritate eyes, nose and throat. To remove
R-134a from system use R-134a recycling equipment that meets
SAE J2210 specifications. If accidental system discharge
occurs, ventilate work area before resuming service.
ANTI-LOCK BRAKE SYSTEM
The anti-lock brake system contains electronic equipment that
can be susceptible to interference caused by improperly installed or
high output radio transmitting equipment. Since this interference
could cause the possible loss of the anti-lock braking capability,
such equipment should be installed by qualified professionals.
On models equipped with anti-lock brake systems, ALWAYS
observe the following cautions:
* DO NOT attempt to bleed hydraulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES Section.
* DO NOT mix tire sizes. As long as tires remain close to the
original diameter, increasing the width is acceptable.
Rolling diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* Use ONLY recommended brake fluids. DO NOT use silicone brake
fluids in an ABS-equipped vehicle.
REPLACING BLOWN FUSES
Before replacing a blown fuse, remove ignition key, turn off
all lights and accessories to avoid damaging the electrical system. Be
sure to use fuse with the correct indicated amperage rating. The use
of an incorrect amperage rating fuse may result in a dangerous
electrical system overload.
BATTERY WARNING
WARNING: When battery is disconnected, vehicles equipped with
computers may lose memory data. When battery power is
restored, driveability problems may exist on some vehicles.
These vehicles may require a relearn procedure. See
appropriate COMPUTER RELEARN PROCEDURES article in the
GENERAL INFORMATION section below.
BRAKE FLUID
For vehicles equipped with a traction control system, idle
engine while pouring brake fluid into reservoir.
CATALYTIC CONVERTER
Continued operation of vehicle with a severe malfunction
could cause converter to overheat, resulting in possible damage to
converter and vehicle.
ELECTROSTATIC DISCHARGE SENSITIVE (ESD) PARTS
WARNING: Many solid state electrical components can be damaged by
static electricity (ESD). Some will display a warning label,
but many will not. Discharge personal static electricity by
Page 698 of 1333
touching a metal ground point on the vehicle prior to
servicing any ESD sensitive component.
ENGINE OIL
CAUTION: Never use non-detergent or straight mineral oil.
FUEL SYSTEM SERVICE
WARNING: Relieve fuel system pressure prior to servicing any fuel
system component (fuel injection models).
HALOGEN BULBS
Halogen bulbs contain pressurized gas which may explode if
overheated. DO NOT touch glass portion of bulb with bare hands. Eye
protection should be worn when handling or working around halogen
bulbs.
POWER STEERING FLUID
When adding power steering fluid, avoid spilling. Damage to
alternator, located beneath power steering reservoir, could result.
RADIATOR CAP
CAUTION: Always disconnect the fan motor when working near the
radiator fan. The fan is temperature controlled and could
start at any time even when the ignition key is in the OFF
position. DO NOT loosen or remove radiator cap when cooling
system is hot.
RADIATOR FAN
WARNING: Keep hands away from radiator fan. Fan is controlled by a
thermostatic switch which may come on or run for up to 15
minutes even after engine is turned off.
SERVICE POINT LOCATIONS
Fig. 1: Service Point Locations (1987-91 2.6L 4-Cylinder Engine)
Courtesy of Mitsubishi Motor Sales of America.
Page 713 of 1333
![MITSUBISHI MONTERO 1991 Repair Manual \b\
\
\
\
\
\
\
Fuel Filter](/img/19/57332/w960_57332-712.png "MITSUBISHI MONTERO 1991 Repair Manual \b\
\
\
\
\
\
\
Fuel Filter")
\b\
\
\
\
\
\
\
Fuel Filter
\b\
\
\
\
\
\
\
Spark Plugs
\b\
\
\
\
\
\
\
Ignition Cables
\b\
\
\
\
\
\
\
Camshaft Timing Belt
\b\
\
\
\
\
\
\
Engine Coolant
\b\
\
\
\
\
\
\
Drive Axle Fluid (With Limited-Slip Differential)
\b\
\
\
\
\
\
\
Engine Oil & Filter
\b\
\
\
\
\
\
\
Automatic Transmission & Transfer Case Fluids
\b\
\
\
\
\
\
\
Vacuum Control System Solenoid Valve Air Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
F (-23
C) ........... SAE 90, 85W-90, 80W-90
API GL-5
Maximum Temperature
Less Than -30
F (-34
C) .................... SAE 75W API GL-5
Power Steering Fluid ............................. Dexron-II ATF
Rear Axle (With Limited
Slip Differential) ............ Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic ...................................... Dexron-II ATF
Manual Transaxle &
Transfer Case (4WD) ................. SAE 75W-85W, 75W-90 API
GL-4 Or GL-5
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Automatic Transmission
1987-93 ...................................... 7.6 Qts. (7.2L)
1994 (3.0L SOHC) ............................. 7.6 Qts. (7.2L) \
1994 (3.0L DOHC & 3.5L) ...................... 9.0 Qts. (8.5L) \
1995 ......................................... 7.9 Qts. (7.5L)
Cooling System
1987-88 ...................................... 8.5 Qts. (8.0L)
1989-95
Page 723 of 1333
![MITSUBISHI MONTERO 1991 Repair Manual Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\](/img/19/57332/w960_57332-722.png "MITSUBISHI MONTERO 1991 Repair Manual Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\")
Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\
\
Carburetor Choke Mechanism & Linkage (2.6L Engine)
\b\
\
\
\
\
\
\
Crankcase Emission Control System (PCV Valve)
\b\
\
\
\
\
\
\
Evaporative Emission Control System
\b\
\
\
\
\
\
\
Distributor Cap, Rotor & Spark Advanced System
\b\
\
\
\
\
\
\
Intake Temperature Control System
\b\
\
\
\
\
\
\
Secondary Air System
\b\
\
\
\
\
\
\
Front Disc Pads
\b\
\
\
\
\
\
\
Rear Drum Brake Linings & Wheel & Cylinders
\b\
\
\
\
\
\
\
Brake Hoses
\b\
\
\
\
\
\
\
Steering Linkage Seals & Drive Shaft Boots
\b\
\
\
\
\
\
\
Lubricate Ball Joints
\b\
\
\
\
\
\
\
Lubricate Front Wheel Bearing
\b\
\
\
\
\
\
\
Drive Axle Fluid (Without Limited-Slip Differential)
\b\
\
\
\
\
\
\
Lubricate Drive Shaft Joints
\b\
\
\
\
\
\
\
Exhaust System
\b\
\
\
\
\
\
\
Drive Belt (Water Pump & Alternator)
\b\
\
\
\
\
\
\
Vacuum, Water, Crankcase Ventilation & Secondary Air Hoses
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Air Filter
\b\
\
\
\
\
\
\
Fuel Filter
\b\
\
\
\
\
\
\
Spark Plugs
\b\
\
\
\
\
\
\
Ignition Cables
\b\
\
\
\
\
\
\
Camshaft Timing Belt
\b\
\
\
\
\
\
\
Engine Coolant
\b\
\
\
\
\
\
\
Drive Axle Fluid (With Limited-Slip Differential)
\b\
\
\
\
\
\
\
Engine Oil & Filter
\b\
\
\
\
\
\
\
Automatic Transmission & Transfer Case Fluids
\b\
\
\
\
\
\
\
Vacuum Control System Solenoid Valve Air Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4