brake fluid MITSUBISHI MONTERO 1991 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 16 of 1333
actuator (if equipped). Remove all drive belts. Remove alternator.
Remove drive belt tensioner assembly.
2) Using Holder (MB990767) and Adapter Bolts (MD998754),
remove crankshaft pulley. See Fig. 12. Disconnect brake fluid level
sensor. Remove upper timing belt covers. Support engine. Remove front
engine mount through bolt and front engine mount.
NOTE: Apply spray lubricant on reamer bolt during removal as bolt
is sometimes seized in engine support bracket.
Fig. 12: Exploded View of Timing Belt Components (DOHC)
Courtesy of Mitsubishi Motor Sales of America, Inc.
3) Remove drive belt idler pulley. Remove engine support
bracket bolts in proper sequence. See Fig. 10. Remove engine support
Page 161 of 1333
\003
AN TI- L O CK B RAK E S A FE TY P R EC AU TIO NS
1991 M it s u bis h i M onte ro
GENERAL INFORMATION
Anti-Lock Brake Safety Precautions
* PLEASE READ THIS FIRST *
This article is intended for general information purposes
only. This information may not apply to all makes and models. If
vehicle is equipped with Anti-Lock Brake System (ABS), refer to
appropriate ANTI-LOCK BRAKE SYSTEM article in the BRAKES section for
description, operation, depressurizing, testing, system bleeding,
trouble shooting and servicing of specific system.
WARNING: Failure to depressurize ABS could lead to physical injury.
ANTI-LOCK BRAKE SAFETY PRECAUTIONS
WARNING: Failure to depressurize ABS could lead to physical injury.
* NEVER open a bleeder valve or loosen a hydraulic line
while ABS is pressurized.
* NEVER disconnect or reconnect any electrical connectors
while ignition is on. Damage to ABS control unit may result.
* DO NOT attempt to bleed hyudarulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES section.
* Only use specially designed brake hoses/lines on ABS equipped
vehicles.
* DO NOT tap on speed sensor components (sensor, sensor rings).
Sensor rings must be pressed into hubs, NOT hammered into
hubs. Striking these components can cause demagnetization or
a loss of polarization, affecting the accuracy of the speed
signal returning to the ABS control unit.
* DO NOT mix tire sizes. Increasing the width, as long as tires
remain close to the original diameter, is acceptable. Rolling
diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* DO NOT contaminate speed sensor components with grease. Only
use recommended coating, when system calls for an
anti-corrosion coating.
* When speed sensor components have been removed, ALWAYS check
sensor-to-ring air gaps when applicable. These specifications
can be found in each appropriate article.
* ONLY use rocommended brake fluids. DO NOT use silicone brake
fluids in an ABS equipped vehicle.
* When instlling transmittion devices (CB's, telephones, etc.)
on ABS equipped vehicles, DO NOT locate the antenna near the
ABS control unit (or any control unit).
* Disconnect all on-board computers, when using electric
welding equipment.
* DO NOT expose the ABS control unit to prolonged periods of
high heat (185
F/85 C for 2 hours is generally considered a
maximum limit).
Page 174 of 1333
\003* B RAK E S YSTE M U NIF O RM IN SPEC TIO N G UID ELIN ES *
1 991 M it s u bis h i M onte ro
GENERAL INFORMATION
Brake Systems - Motorist Assurance Program
Standards For Automotive Repair
All Makes & Models
CONTENTS
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
OVERVIEW OF SERVICE REQUIREMENTS AND SUGGESTIONS
ACCELEROMETERS (G SENSOR OR LATERAL)
ACCUMULATORS
ANCHOR PINS
ANTI-LOCK BRAKE SYSTEMS
BACKING PLATES
BRAKE FLUID
BRAKE FRICTION MATERIAL
BRAKE PADS
BRAKE PEDALS
BRAKE SHOES
BRAKE SHOE HARDWARE
BRAKE STOPLIGHT SWITCHES
BULB SOCKETS
BULBS AND LEDS
CALIPER HARDWARE
CALIPERS
CONTROLLERS
DIGITAL RATIO AXLE CONTROLLERS AND BUFFERS (DRAC AND DRAB)
DISABLE SWITCHES
DRUMS
ELECTRICAL PUMPS AND MOTORS
ELECTRONIC CONTROLLERS
FLUID
FLUID LEVEL SENSOR SWITCHES
FOUR WHEEL DRIVE SWITCHES
FRICTION MATERIAL
G SENSORS
HOSES
HYDRAULIC MODULATORS
HYDRO-BOOSTERS
HYDRO-ELECTRIC BOOSTERS (POWERMASTER)
IGNITION DISABLE SWITCHES
LATERAL ACCELERATION SWITCHES
LEDS
LENSES
MASTER CYLINDERS
MODULATORS
MOTORS
PARKING BRAKE SWITCHES
PARKING BRAKE SYSTEMS
PADS
PEDAL TRAVEL SWITCHES
PEDALS
POWERMASTER
PUMPS
PRESSURE DIFFERENTIAL SWITCHES
PRESSURE SWITCHES
RELAYS
ROTORS
SELF-ADJUSTING SYSTEMS
Page 179 of 1333
NOTE: Electro-magnetic interference (EMI) may be caused by
incorrect installation of accessories or components. EMI can
result in improper system operation.
BACKING PLATES
BACKING PLATE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Anchor pin bent ......... B .. Require repair or replacement.
Anchor pin broken ....... A ............ Require replacement.
Anchor pin worn, affecting
structural integrity ... B ............ Require replacement.
Backing plate bent ...... B .. Require repair or replacement.
Backing plate broken .... A ............ Require replacement.
Backing plate cracked ... B .. Require repair or replacement.
Corroded, affecting
structural integrity .... A ............ Require replacement.
Loose ................... B .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Shoe lands worn ......... A .. Require repair or replacement.
\
\
\
\
\
\
\
BRAKE FLUID
CAUTION: Most manufacturers prohibit the use of DOT 5 brake fluid
in a system equipped with ABS.
DOT 3, DOT 4, and DOT 5.1 brake fluids are clear or light
amber in color. DOT 5 brake fluid is violet in color. Correct fluid
required for the brake system is stamped on the master cylinder cover.
BRAKE FLUID INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Beyond service interval . 3 .. Suggest flushing and refilling
with correct fluid.
Brake fluid type
incorrect .............. B .. Require flushing and refilling
with correct fluid.
Contaminated, for example,
fluid other than brake
fluid present .......... A or B ....... ( 1) Require service.
Hydraulic component ..... 3 .. Suggest flushing and refilling
overhaul or replacement with correct fluid.
Rubber master cylinder
cover gasket distorted
and gummy .............. A .......... ( 2) Require replacement
of gasket.
( 1) - If a fluid other than brake fluid is present in the brake
system which DOES affect the rubber parts, the required
service is to:
* Remove all components having rubber parts from the
system.
* Flush lines with denatured alcohol or brake cleaner
* Repair or replace all components having rubber parts
* Flush and fill with correct brake fluid. (Code A)
If a fluid other than brake fluid is present in the brake
Page 180 of 1333
system which DOES NOT affect the rubber parts, the required
service is to flush and fill with the correct brake fluid.
(Code B)
( 2) - This condition may indicate contaminated brake fluid.
\
\
\
\
\
\
\
BRAKE FRICTION MATERIAL
See FRICTION MATERIAL .
BRAKE PADS
See FRICTION MATERIAL .
BRAKE PEDALS
BRAKE PEDAL INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent, affecting
performance ............ A .. Require repair or replacement.
Broken .................. A .. Require repair or replacement.
Pedal pad missing ....... C .... Require replacement of pedal
pad.
Pedal pad worn .......... 1 ............ Suggest replacement.
Pivot bushings worn,
affecting performance .. A .... Require replacement of pivot
bushings.
\
\
\
\
\
\
\
BRAKE SHOES
See FRICTION MATERIAL .
BRAKE SHOE HARDWARE
See also SELF-ADJUSTING SYSTEMS .
BRAKE SHOE HARDWARE INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Broken .................. A ............ Require replacement.
Distorted ............... A ............ Require replacement.
Missing ................. C ............ Require replacement.
Surfaces rust-pitted .... 1 ............ Suggest replacement.
Worn, affecting
performance ............ A ............ Require replacement.
\
\
\
\
\
\
\
BRAKE STOPLIGHT SWITCHES
BRAKE STOPLIGHT INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Page 188 of 1333
hardware.
Attaching hardware threads
damaged ................ A ... Require repair or replacement
of hardware.
Attaching hardware threads
stripped (threads
missing) ............... A ... Require repair or replacement
of hardware.
Code set (if
applicable) ............ A .......... (1) Further inspection
required.
Connector broken ........ A .. Require repair or replacement.
Connector melted ........ A ........... ( 2) Require repair or
replacement.
Connector missing ....... A ................. Require repair.
Contaminated ............ A .. Require repair or replacement.
Inoperative ............. B .. Require repair or replacement.
( 3) Further inspection required.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 2) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
( 1) - Refer to manufacturer's diagnostic trouble code procedure
and require repair or replacement of affected component(s).
( 2) - Determine cause and correct prior to repair or replacement
of part.
( 3) - Inoperative includes intermittent operation or out of OEM
specification. Some components may be serviceable. Check
for accepted cleaning procedure.
\
\
\
\
\
\
\
FLUID
See BRAKE FLUID.
FLUID LEVEL SENSOR SWITCHES
See SWITCHES.
FOUR WHEEL DRIVE SWITCHES
See SWITCHES.
Page 193 of 1333
![MITSUBISHI MONTERO 1991 Service Manual LATERAL ACCELERATION SWITCHES
See ACCELEROMETERS .
LEDS
See BULBS AND LEDS .
LENSES
LENSE INSPECTION \
\](/img/19/57332/w960_57332-192.png "MITSUBISHI MONTERO 1991 Service Manual LATERAL ACCELERATION SWITCHES
See ACCELEROMETERS .
LEDS
See BULBS AND LEDS .
LENSES
LENSE INSPECTION \
\")
LATERAL ACCELERATION SWITCHES
See ACCELEROMETERS .
LEDS
See BULBS AND LEDS .
LENSES
LENSE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... A ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Broken, affecting
performance ............ A ............ Require replacement.
Broken, not affecting
performance ............ .. ........ No service suggested or
required.
Cracked ................. A ............ Require replacement.
Discolored .............. A ............ Require replacement.
Leaking ................. A .. Require repair or replacement.
Melted, affecting
performance ............ A ............ Require replacement.
Melted, not affecting
performance ............ 2 ............ Suggest replacement.
Missing ................. C ............ Require replacement.
\
\
\
\
\
\
\
MASTER CYLINDERS
MASTER CYLINDER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Brake fluid leaking from
rear of master cylinder
bore ................... B .. Require repair or replacement.
Brake pedal drops
intermittently ......... A ........... ( 1) Require repair or
replacement.
Fluid level low ......... .. ......... ( 2) Further inspection
required.
Internal valve failure .. A .. Require repair or replacement.
Master cylinder leaking
brake fluid internally . A .. Require repair or replacement.
Piston does not return .. A .. Require repair or replacement.
Ports plugged ........... A .. Require repair or replacement.
Rubber master cylinder
cover gasket distorted
and gummy .............. A .. ( 3) Require replacement of the
gasket.
Page 194 of 1333
(1) - This condition may be normal on some vehicles equipped with
anti-lock brakes.
( 2) - Refer to OEM procedures for adjusting low fluid level.
Inspect for brake hydraulic system leaks and friction
material wear.
( 3) - This condition may indicate contaminated brake fluid.
See BRAKE FLUID .
\
\
\
\
\
\
\
MODULATORS
See HYDRAULIC MODULATORS .
MOTORS
See ELECTRICAL PUMPS AND MOTORS .
PARKING BRAKE SWITCHES
See SWITCHES.
PARKING BRAKE SYSTEMS
NOTE: The parking brake is an integral part of the brake
system. It is important that the parking brake function
properly when brake service is performed.
PARKING BRAKE SYSTEM INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Cable improperly
adjusted ............... B ....... Require cable adjustment.
Cable or individual
wires in the cable
are broken ............. A .... Require replacement of cable
assembly.
Cable sticking .......... A ...... Require cable lubrication.
Cable stuck inside conduit
and cannot be lubricated
so that parking brake
functions properly ..... A .... Require replacement of cable
assembly.
Inoperative ( 1) ......... A .......... Require replacement of
inoperative parts.
Parking brake
parts bent ............. B ... Require repair or replacement
of bent parts.
Parking brake
parts broken ........... A ... Require replacement of broken
parts.
Parking brake parts
Page 199 of 1333
specifications.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
(1) - If a sensor is not adjustable, further inspection is
required to identify and correct cause.
( 2) - Determine cause and correct prior to repair or
replacement of part.
( 3) - Determine source of contamination, such as metal
particles or water. Require repair or replacement.
( 4) - Inoperative includes intermittent operation or out of OEM
specification. Some components may be serviceable; check
for accepted cleaning procedure.
\
\
\
\
\
\
\
STEEL BRAKE LINES
STEEL BRAKE LINE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Corroded, affecting
structural integrity ... A ............ Require replacement.
Fitting incorrect (for
example, compression
fitting) ............... B ............ Require replacement.
Flare type incorrect .... B .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Line material incorrect
(copper, etc.) ......... B ............ Require replacement.
Restricted .............. A ............ Require replacement.
Routed incorrectly ...... B ..... Require routing correction.
Rust-pitted ............. 1 ............ Suggest replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped
(threads missing) ...... A ............ Require replacement.
\
\
\
\
\
\
\
STOPLIGHT SWITCHES
See BRAKE STOPLIGHT SWITCHES .
SWITCHES
NOTE: Copied from Electrical UIGs & added "float saturated" from
old fluid level sensor switches.
STEEL BRAKE LINE INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Page 212 of 1333
5) Remove the LSPV load-sensing spring. Slowly depress the
brake pedal. Check the readings on the pressure gauges. Refer to the
LSPV PRESSURE SPECIFICATIONS table.
6) Install LSPV load-sensing spring. Load weight into rear of
vehicle until measured spring length distance is 7.0" (178 mm) with
lever slightly pressed in. See Fig. 1.
7) Slowly depress brake pedal. Check readings on pressure
gauges. See LSPV PRESSURE SPECIFICATIONS table. If fluid pressure is
not within specification, ensure all other brake system components are
okay. If other components are okay, replace LSPV assembly.
LSPV PRESSURE SPECIFICATIONS (PICKUP & RAM-50)
\
\
\
\
\
\
Application Inlet Pressure Outlet Pressure
psi (kg/cm) psi (kg/cm)
Load-Sensing Spring
Removed ........... 853 (60) ......... 242-327 (17-23)
Installed ........ 1991 (140) .... ( 1) 299-583 (21-40)
( 1) - On vehicles with 2WD and heavy-duty suspension,
outlet pressure is 526-697 psi (37-49 kg/cm
). \
\
\
\
\
\
PROPORTIONING VALVE (NON-LOAD-SENSING) (MONTERO)
Pressure Test
1) Connect pressure gauges to input and output ports of the
proportioning valve. See Fig. 5. Bleed brake hydraulic system. Refer
to BLEEDING BRAKE SYSTEM .
2) Slowly depress brake pedal. Check readings on pressure
gauges. See the PROPORTIONING VALVE PRESSURE SPECIFICATIONS table. If
fluid pressures are not within specification, replace proportioning
valve.
Fig. 5: Connecting Pressure Gauges to Proportioning Valve (Typical)
Courtesy of Mitsubishi Motor Sales of America.
PROPORTIONING VALVE PRESSURE SPECIFICATIONS (MONTERO)
\
\
\
\
\
\