friction material MITSUBISHI MONTERO 1991 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 56 of 1333
Removal
1) Clamp Holding Fixture (J-25008-A) in a vise and attach
compressor to holding fixture with thumb screws. Use Clutch Hub Holder
(J-33027) to hold clutch. Remove shaft nut using Shaft Nut Socket (J-\
9399).
2) Thread Clutch Plate and Hub Assembly Remover (J-33013-B)
into hub. Hold body of remover with a wrench and turn center screw
into remover body to remove clutch plate and hub assembly. Remove
shaft key and retain for assembly. See Fig. 5.
NOTE: DO NOT drive or pound on clutch hub or shaft.
Installation
1) Install shaft key into hub key groove. Allow key to
project approximately 1/8" out of key way. Shaft key is curved
slightly to provide an interference fit in hub key groove.
2) Ensure frictional surface of clutch plate and clutch rotor
are clean before installing clutch plate and hub assembly. Align shaft
key with shaft key way and place clutch plate and hub assembly onto
compressor shaft.
3) Hold hex portion of Installer (J-9480-B) with a wrench.
Tighten center screw to press hub into shaft until there is .020-.040"
(.5-1.0 mm) air gap between frictional plate and clutch rotor.
4) Install new shaft nut with small diameter boss of nut
against crankshaft shoulder. Use Thin Wall Socket (J-9399) and Clutch
Hub Holder (J-25030). Tighten shaft nut to 10 ft. lbs. (14 N.m). Spi\
n
pulley rotor by hand to ensure rotor is not rubbing on clutch drive
plate.
HARRISON R4 4-CYL SHAFT SEAL R & I
Removal
1) Clamp Holding Fixture (J-25008-A) in a vise and attach
compressor to holding fixture with thumb screws. Use Clutch Hub Holder
(J-33027) to hold clutch. Remove shaft nut using Shaft Nut Socket (J-\
9399).
2) Thread Clutch Plate and Hub Assembly Remover (J-33013-B)
into hub. Hold body of remover with a wrench and turn center screw
into remover body to remove clutch plate and hub assembly. Remove
clutch plate and shaft key. Pry out dust seal (if equipped). Remove
seal seat snap ring. Thoroughly clean compressor neck area and "O"
ring groove surrounding shaft. Any dirt or foreign material may cause
compressor damage.
3) Use Seal Remover/Installer (J23128-A), remove seal with a\
twisting motion. Use "O" Ring Remover (J-9553-01) to remove "O" ring.
Installation
1) Coat new shaft seal with refrigerant oil and install shaft
seal on remover/installer. Align compressor shaft machined surface
with shaft seal and install. Turn remover/installer slightly
counterclockwise to secure shaft seal tangs.
2) Using Seal Installer (J-33011), install "O" ring and coat\
with refrigerant oil. Coat seal seat with refrigerant oil and install
using seal seat remover/installer. Install snap ring. Install dust
seal (if supplied in seal kit). See Fig. 7.
Page 174 of 1333
\003* B RAK E S YSTE M U NIF O RM IN SPEC TIO N G UID ELIN ES *
1 991 M it s u bis h i M onte ro
GENERAL INFORMATION
Brake Systems - Motorist Assurance Program
Standards For Automotive Repair
All Makes & Models
CONTENTS
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
OVERVIEW OF SERVICE REQUIREMENTS AND SUGGESTIONS
ACCELEROMETERS (G SENSOR OR LATERAL)
ACCUMULATORS
ANCHOR PINS
ANTI-LOCK BRAKE SYSTEMS
BACKING PLATES
BRAKE FLUID
BRAKE FRICTION MATERIAL
BRAKE PADS
BRAKE PEDALS
BRAKE SHOES
BRAKE SHOE HARDWARE
BRAKE STOPLIGHT SWITCHES
BULB SOCKETS
BULBS AND LEDS
CALIPER HARDWARE
CALIPERS
CONTROLLERS
DIGITAL RATIO AXLE CONTROLLERS AND BUFFERS (DRAC AND DRAB)
DISABLE SWITCHES
DRUMS
ELECTRICAL PUMPS AND MOTORS
ELECTRONIC CONTROLLERS
FLUID
FLUID LEVEL SENSOR SWITCHES
FOUR WHEEL DRIVE SWITCHES
FRICTION MATERIAL
G SENSORS
HOSES
HYDRAULIC MODULATORS
HYDRO-BOOSTERS
HYDRO-ELECTRIC BOOSTERS (POWERMASTER)
IGNITION DISABLE SWITCHES
LATERAL ACCELERATION SWITCHES
LEDS
LENSES
MASTER CYLINDERS
MODULATORS
MOTORS
PARKING BRAKE SWITCHES
PARKING BRAKE SYSTEMS
PADS
PEDAL TRAVEL SWITCHES
PEDALS
POWERMASTER
PUMPS
PRESSURE DIFFERENTIAL SWITCHES
PRESSURE SWITCHES
RELAYS
ROTORS
SELF-ADJUSTING SYSTEMS
Page 180 of 1333
system which DOES NOT affect the rubber parts, the required
service is to flush and fill with the correct brake fluid.
(Code B)
( 2) - This condition may indicate contaminated brake fluid.
\
\
\
\
\
\
\
BRAKE FRICTION MATERIAL
See FRICTION MATERIAL .
BRAKE PADS
See FRICTION MATERIAL .
BRAKE PEDALS
BRAKE PEDAL INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent, affecting
performance ............ A .. Require repair or replacement.
Broken .................. A .. Require repair or replacement.
Pedal pad missing ....... C .... Require replacement of pedal
pad.
Pedal pad worn .......... 1 ............ Suggest replacement.
Pivot bushings worn,
affecting performance .. A .... Require replacement of pivot
bushings.
\
\
\
\
\
\
\
BRAKE SHOES
See FRICTION MATERIAL .
BRAKE SHOE HARDWARE
See also SELF-ADJUSTING SYSTEMS .
BRAKE SHOE HARDWARE INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Broken .................. A ............ Require replacement.
Distorted ............... A ............ Require replacement.
Missing ................. C ............ Require replacement.
Surfaces rust-pitted .... 1 ............ Suggest replacement.
Worn, affecting
performance ............ A ............ Require replacement.
\
\
\
\
\
\
\
BRAKE STOPLIGHT SWITCHES
BRAKE STOPLIGHT INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Page 183 of 1333
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
(1) - Application incorrect includes wrong bulb coating
or color.
( 2) - Determine cause and correct prior to repair or
replacement of part.
\
\
\
\
\
\
\
CALIPER HARDWARE
CALIPER HARDWARE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent ................... A .. Require repair or replacement.
Broken .................. A .. Require repair or replacement.
Corroded, affecting
performance ............ A .. Require repair or replacement.
Dust boots on slider pin
(bolt) missing ......... C ... Require replacement of boots.
Dust boots on slider pin
(bolt) torn ............ A ... Require replacement of boots.
Missing ................. C ............ Require replacement.
Shim bent ............... A ............. ( 1) Require removal
or replacement.
Shim (OE standard)
missing ................ C ........ ( 2) Require replacement.
Shim out of position .... B ............. ( 1) Require removal
or replacement.
Shim worn ............... A ............. ( 1) Require removal
or replacement.
Slider pin (bolt) bent .. B ... Require replacement of slider
pin or bolt and lubricants.
Slider pin (bolt)
rust-pitted ............ A ... Require replacement of slider
pin or bolt and lubricants.
Slider pin (bolt) worn .. A ... Require replacement of slider
pin or bolt and lubricants.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Worn, affecting
performance ............ A ............ Require replacement.
( 1) - Removal is acceptable if shim is not OE.
( 2) - Aftermarket shims may be suggested to reduce noise.
\
\
\
\
\
\
\
CALIPERS
You are not required to replace or rebuild calipers in axle
sets. However, when replacing or rebuilding a caliper due to the
conditions that follow, you may suggest servicing, rebuilding, or
replacement of the other caliper (on the same axle) for improved
performance and preventive maintenance (for example, the part is close
to the end of its useful life, replacing the caliper may extend pad
life, or contribute to more balanced braking).
CAUTION: When installing loaded calipers, it is required that
friction material be matched in axle sets for consistent
braking characteristics.
Page 185 of 1333
of caliper.
Piston sticking ......... A ........... Require rebuilding or
replacement of caliper.
Slide mechanism
sticking ............... A ... Require repair or replacement
of slide mechanism.
(1) - Only required if the hydraulic system must be opened.
( 2) - Seized is defined as a bleeder screw that cannot be
removed after a practical attempt at removing. Only
required if the hydraulic system must be opened.
\
\
\
\
\
\
\
CONTROLLERS
See ELECTRONIC CONTROLLERS .
DIGITAL RATIO AXLE CONTROLLERS AND BUFFERS (DRAC AND DRAB)
DIGITAL RATIO AXLE CONTROLLER AND BUFFER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........ ( 1) Require replacement.
Connector missing ....... C ............ Require replacement.
Missing ................. C ............ Require replacement.
Output signal incorrect . B .. Require repair or replacement.
Terminal burned, affecting
performance ............ A .............. ( 2) Require repair
or replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
( 1) - Determine cause and correct prior to replacement of part.
( 2) - Determine cause and correct prior to repair or
replacement of part.
\
\
\
\
\
\
\
DISABLE SWITCHES
See SWITCHES.
DRUMS
Determine the need to recondition based upon individual drum
conditions that follow. Friction material replacement does not require
drum reconditioning unless other justifications exist. DO NOT
recondition new drums unless they are being pressed or bolted onto an
existing hub. It is not necessary to replace drums in axle sets.
However, when replacing or reconditioning a drum due to the conditions
that follow, you may suggest reconditioning of the other drum on the
Page 189 of 1333
FRICTION MATERIAL
NOTE: Original Equipment Manufacturer (OEM) specifications
designate replacement at different thicknesses.
CAUTION: It is required that friction material be matched in axle
sets for consistent braking characteristics.
FRICTION MATERIAL INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Contaminated, for example,
fluid that leaked from
caliper, wheel cylinder,
or axle seal ........... A ........ ( 1) Require replacement.
Cracked through ......... B Require replacement.
Flaking or chunking ..... B Require replacement.
Glazed (shiny) .......... .. ........ No service suggested or
required.
Grooves or ridges ....... .. .... ( 2) No service suggested or
required.
Permanently attached
hardware bent .......... A ............ Require replacement.
Permanently attached
hardware broken ........ A ............ Require replacement.
Permanently attached
hardware loose ......... A ............ Require replacement.
Permanently attached
hardware missing ....... C ............ Require replacement.
Permanently attached
hardware seized ........ A .. Require repair or replacement.
Rivets loose ............ B ............ Require replacement.
Separating from backing . B ............ Require replacement.
Shoe table or web bent .. B ............ Require replacement.
Shoe table or web
cracked ................ A ............ Require replacement.
Shoe table or web worn,
affecting performance .. A ............ Require replacement.
Surface cracking ........ .. ........ No service suggested or
required. Further inspection
may be necessary to determine
cause.
Tapered wear ............ B ........ ( 3) Suggest replacement.
Thickness of one pad is
greater than opposite pad
in the same caliper
(uneven wear) .......... .. .... ( 4) Replacement of friction
material not suggested or
required. Further inspection
required. See CALIPERS
and CALIPER HARDWARE.
Wear indicator device
(electronic) contacts
rotor .................. B ...... ( 5) Require replacement of
appropriate parts.
Wear indicator device
(mechanical) bent ....... .. .......... ( 6) Further inspection
required.
Wear indicator device
(mechanical) broken .... .. ......... ( 6) Further inspection
required.
Page 190 of 1333
Wear indicator device
(mechanical) contacts
rotor .................. .. ......... (6) Further inspection
required.
Worn close to minimum
specifications ......... 1 ........ ( 7) Suggest replacement.
Worn to, or below minimum
specifications ......... B ............ Require replacement.
( 1) - Identify and repair cause of contamination prior to
replacing friction material.
( 2) - When reconditioning or replacing drums or rotors,
replacement of friction material may be suggested
depending on the severity of the grooves or ridges.
( 3) - Some vehicles use pads that are tapered by design. Refer
to specific vehicle application. If not normal, require
replacement of pads and correction of cause.
( 4) - Uneven pad thickness is normal on some vehicles. Refer to
specific vehicle applications.
( 5) - The pad wear indicator light may come on due to other
electrical problems.
( 6) - Explain to the customer that the purpose of the wear
indicator is to alert him or her to check for friction
wear. Wear indicators may be bent or broken. Therefore,
the friction material must be measured. The need for
friction material replacement is determined based upon
the conditions stated in this section. Periodic inspection
is suggested.
( 7) - When the part appears to be close to the end of its useful
life, replacement may be suggested.
\
\
\
\
\
\
\
G SENSORS
See ACCELEROMETERS .
HOSES
HOSE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............. A ... Require repair or replacement
of hardware.
Blistered ............... B ............ Require replacement.
Fitting threads damaged . A .. Require repair or replacement.
Fitting threads stripped
(threads missing) ...... A ............ Require replacement.
Incorrectly secured ..... B ................. Require repair.
Inner fabric
(webbing) cut .......... B ............ Require replacement.
Leaking ................. A ............ Require replacement.
Missing ................. C ............ Require replacement.
Outer covering is cracked
to the extent that
inner fabric of hose
Page 194 of 1333
(1) - This condition may be normal on some vehicles equipped with
anti-lock brakes.
( 2) - Refer to OEM procedures for adjusting low fluid level.
Inspect for brake hydraulic system leaks and friction
material wear.
( 3) - This condition may indicate contaminated brake fluid.
See BRAKE FLUID .
\
\
\
\
\
\
\
MODULATORS
See HYDRAULIC MODULATORS .
MOTORS
See ELECTRICAL PUMPS AND MOTORS .
PARKING BRAKE SWITCHES
See SWITCHES.
PARKING BRAKE SYSTEMS
NOTE: The parking brake is an integral part of the brake
system. It is important that the parking brake function
properly when brake service is performed.
PARKING BRAKE SYSTEM INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Cable improperly
adjusted ............... B ....... Require cable adjustment.
Cable or individual
wires in the cable
are broken ............. A .... Require replacement of cable
assembly.
Cable sticking .......... A ...... Require cable lubrication.
Cable stuck inside conduit
and cannot be lubricated
so that parking brake
functions properly ..... A .... Require replacement of cable
assembly.
Inoperative ( 1) ......... A .......... Require replacement of
inoperative parts.
Parking brake
parts bent ............. B ... Require repair or replacement
of bent parts.
Parking brake
parts broken ........... A ... Require replacement of broken
parts.
Parking brake parts
Page 195 of 1333
missing ................ C .. Require replacement of missing
parts.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
(1) - Inoperative includes intermittent operation.
\
\
\
\
\
\
\
PADS
See FRICTION MATERIAL .
PEDAL TRAVEL SWITCHES
See SWITCHES.
PEDALS
See BRAKE PEDALS.
POWERMASTER
See HYDRO-BOOSTERS .
PUMPS
See ELECTRICAL PUMPS AND MOTORS .
PRESSURE DIFFERENTIAL SWITCHES
See SWITCHES.
PRESSURE SWITCHES
See SWITCHES.
RELAYS
NOTE: Copied from Electrical UIGs
RELAY INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Housing broken .......... A ............ Require replacement.
Housing cracked ......... 2 ............ Suggest replacement.
Inoperative ( 1) ......... A ............ Require replacement.
Missing ................. C ............ Require replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned,
affecting performance .. A ........... ( 2) Require repair or
replacement.
Page 196 of 1333
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
(1) - Inoperative includes intermittent operation or out of OEM
specification.
( 2) - Determine cause and correct prior to repair or
replacement of part.
\
\
\
\
\
\
\
ROTORS
Determine the need to recondition based upon individual rotor
conditions that follow. Friction material replacement does not require
rotor reconditioning unless other justifications exist. DO NOT
recondition new rotors unless they are being pressed or bolted onto an
existing hub. It is not necessary to replace rotors in axle sets.
However, when replacing or reconditioning a rotor due to the
conditions that follow, you may suggest reconditioning of the other
rotor on the same axle to eliminate uneven braking behavior.
Determine the need to replace based upon the individual rotor
conditions that follow. Reconditioning is defined as machining and
block sanding, or block sanding only. Block sanding is defined as
using 120-150 grit sandpaper with moderate to heavy force for 60
seconds per side. Always wash rotors after servicing or before
installing.
ROTOR INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Corrosion affecting
structural integrity ... A ........ ( 1) Require replacement.
Cracked ................. B ............ Require replacement.
Hard spots .............. 2 ....... Suggest reconditioning or
replacement of rotor according
to OEM specifications.
Lateral runout (wobble)
exceeds OEM
specifications ......... B ............ Require re-indexing,
reconditioning, or replacement
according to specifications.
Measured thickness is less
than OEM discard
specifications ......... B ............ Require replacement.
Rotor thickness is less
than OEM "machine to"
specifications but thicker
than "discard at"
specifications, and the
rotor does not require
reconditioning ......... 1 ........ ( 2) Suggest replacement.
Rotor thickness will be
less than OEM "machine to"
specifications after
required