oil filter MITSUBISHI MONTERO 1998 User Guide
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 600 of 1501
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Restricted, affecting
performance ............ A .. Require repair or replacement.
\
\
\
\
\
\
\
AIR FILTER ELEMENTS
AIR FILTER ELEMENT INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Leaking ................. A ............ Require replacement.
Paper filter element
oil-soaked ............ A ........ ( 1) Require replacement.
Maintenance intervals ... 3 ... Suggest replacement to comply
with vehicle's OEM recommended
service intervals.
Melted .................. A ........... Required replacement.
Missing ................. C ............ Require replacement.
Restricted, affecting
performance ............ A ............ Require replacement.
Water-contaminated ...... A ........ ( 1) Require replacement.
( 1) - Further inspection required to determine cause.
\
\
\
\
\
\
\
AIR FILTER GASKETS
See AIR FILTER HOUSINGS AND GASKETS .
AIR FILTER HOUSINGS AND GASKETS
AIR FILTER HOUSING AND GASKET INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
\
\
\
\
\
\
\
AIR FUEL RATIO SENSORS
Page 629 of 1501
(1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Determine source of contamination, such as engine
coolant, fuel, metal particles, or water. Require
repair or replacement.
( 3) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\
ENGINE COOLING SYSTEMS
NOTE: Overheating, poor engine performance, and insufficient
cabin heat can be affected by, but are not limited to,
all of the components in the engine cooling system.
ENGINE COVERS (OIL PAN, VALVE COVER, TIMING COVER)
ENGINE COVER (OIL PAN, VALVE COVER, TIMING COVER) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
incorrect .............. B ............ Require replacement.
Attaching hardware
loose .................. A .. Require repair or replacement.
Attaching hardware
missing ................ C ............ Require replacement.
Baffle loose ............ 2 .. Suggest repair or replacement.
Baffle missing .......... C ............ Require replacement.
Bent, affecting
performance ............ A .. Require repair or replacement.
Bent, not affecting
performance ............ .. ....... No service suggested or
required.
Cracked (not leaking) ... 2 .. Suggest repair or replacement.
Leaking externally ...... A .. Require repair or replacement.
Leaking internally,
causing fluid
contamination .......... A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Restricted passage ...... A .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
\
\
\
\
\
\
\
ENGINE OIL
ENGINE OIL INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Contaminated ............ A .. ( 1) Require replacement of oil
and filter.
Level high .............. B ... Determine source of incorrect
level and require repair.
Level low ............... B ... Determine source of incorrect
level and require repair.
Maintenance intervals ... 3 ... Suggest replacement to comply
with vehicle's OEM recommended
service intervals.
( 1) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water when changing oil. Require
Page 630 of 1501
![MITSUBISHI MONTERO 1998 User Guide repair or replacement. \
\
\
\
\
\
\
ENGINE OIL CANISTER](/img/19/57333/w960_57333-629.png "MITSUBISHI MONTERO 1998 User Guide repair or replacement. \
\
\
\
\
\
\
ENGINE OIL CANISTER")
repair or replacement. \
\
\
\
\
\
\
ENGINE OIL CANISTERS
See ENGINE OIL FILTERS AND CANISTERS .
ENGINE OIL COOLERS (EXTERNAL)
ENGINE OIL COOLER (EXTERNAL) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Air flow restriction .... A .. Require repair or replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bypassed ................ A .. Require repair or replacement.
Connection leaking ...... A .. Require repair or replacement.
Corroded ................ 1 .. Suggest repair or replacement.
Fins damaged, affecting
performance ............ A .. Require repair or replacement.
Fins damaged, not
affecting performance .. 2 .. Suggest repair or replacement.
Fluid flow restrictions . A .. Require repair or replacement.
Internal restrictions,
affecting performance .. A .. Require repair or replacement.
Leaking ................. A .. Require repair or replacement.
Missing ................. A ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
\
\
\
\
\
\
\
ENGINE OIL DRAIN PLUGS AND GASKETS
ENGINE OIL DRAIN PLUG AND GASKET INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Threads damaged ......... A ........... ( 1) Require repair or
replacement.
( 1) - Some OEMs require replacement of drain plug gasket when
removing drain plug. Inspect threads in oil pan for damage.
\
\
\
\
\
\
\
ENGINE OIL FILTERS AND CANISTERS
ENGINE OIL FILTER AND CANISTER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bulged .................. A ........ ( 1) Require replacement.
Page 631 of 1501
Further inspection required.
Canister attaching
hardware broken ........ A ... Require repair or replacement
of hardware.
Canister attaching
hardware loose ......... A ................. Require repair.
Canister attaching
hardware missing ....... C ............ Require replacement.
Canister attaching
hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Center tube collapsed ... A ........ (2) Require replacement.
Further inspection required.
Contaminated ............ A ...... ( 3) Require replacement of
oil and filter.
Dented .................. 2 ........ ( 4) Suggest replacement.
Further inspection required.
Leaking ................. A .. Require repair or replacement.
Maintenance intervals ... 3 ... Suggest replacement to comply
with vehicle's OEM recommended
service intervals.
( 1) - Inspect pressure relief valve.
( 2) - Inspect bypass.
( 3) - Determine cause of contamination, such as engine coolant,
fuel, metal particles, or water when changing oil. Require
repair or replacement.
( 4) - Determine cause, such as broken motor mount.
\
\
\
\
\
\
\
ENGINE OIL GASKETS
See ENGINE OIL DRAIN PLUGS AND GASKETS .
ENGINE OIL PRESSURE GAUGES (MECHANICAL)
ENGINE OIL PRESSURE GAUGE (MECHANICAL) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Indicates out of range .. B .......... ( 1) Further inspection
required.
Inoperative ............. A .......... ( 2) Further inspection
required.
Leaking ................. A .. Require repair or replacement.
Reads inaccurately ...... 2 .. Suggest repair or replacement.
( 1) - Gauge may indicate problem with contaminated oil, level,
pressure, or temperature, or problem with gauge.
( 2) - Gauge may indicate problem with contaminated oil, level,
pressure, or temperature, or problem with gauge.
Inoperative includes intermittent operation, out of OEM
specification, or out of range. Further inspection
required to determine cause.
\
\
\
\
\
\
\
EVAPORATIVE EMISSION (EVAP) CANISTER FILTERS
EVAPORATIVE EMISSION (EVAP) CANISTER FILTER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Page 965 of 1501
![MITSUBISHI MONTERO 1998 User Guide FLUID CAPACITIES
FLUID CAPACITIES TABLE ( 1) \
\
\
\
\
\
\](/img/19/57333/w960_57333-964.png "MITSUBISHI MONTERO 1998 User Guide FLUID CAPACITIES
FLUID CAPACITIES TABLE ( 1) \
\
\
\
\
\
\")
FLUID CAPACITIES
FLUID CAPACITIES TABLE ( 1) \
\
\
\
\
\
\
Item Condition Specification
\
\
\
\
\
\
\
\f
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1)
\
\
\
\
\
\
\f
Oil Filter 0.32 Qts. (0.3L)
\
\
\
\
\
\
\f
Oil Cooler 0.32 Qts. (0.3L)
\
\
\
\
\
\
\
\f
Power Drained 1.1 Qts. (1.0L)
Steering
\
\
\
\
\
\
\
\f
Automatic Drained 8.9 Qts. (8.5L)
Transmission
\
\
\
\
\
\
\
\f
Manual Drained 3.3 Qts. (3.2L)
Transmission
\
\
\
\
\
\
\
\f
Transfer Case Drained 2.6 Qts. (2.5L)
\
\
\
\
\
\
\
\f
Front Axle Drained 1.3 Qts. (1.2L)
\
\
\
\
\
\
\
\f
Rear Axle Drained 3.3 Qts. (3.2L)
\
\
\
\
\
\
\
\f
A/C Drained 27 oz (760 g)
Refrigerant
\
\
\
\
\
\
\
\f
Fuel Tank Capacity 24 gal (92L)
\
\
\
\
\
\
\
\f
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\
\
\
\
\
\
\
WHEEL & TIRE SPECIFICATIONS
Tire specifications are imprinted on the tire side wall. The
recommended cold tire inflation pressures are listed on a label
attached to the rear face of the driver's door. These pressures
provide the best combination of ride comfort, tire wear and stability
under normal conditions.
CAUTION: DO NOT mix tires of different design such as radial ply
with bias or bias-belted tires. Mixing tire types will
adversely affect road handling and may lead to loss of
vehicle control. When using snow tires, they must be used
in set of four for maneuverability and safety. DO NOT use
tire chains on front wheels.
TIRE & WHEEL SPECIFICATIONS TABLE
\
\
\
\
\
\
Wheel Size Tire Size
15 x 6JJ (Steel or Aluminum) .................. P235/75R15
15 X 7JJ (Aluminum) ........................... P265/70R15
\
\
\
\
\
\
WHEEL TIGHTENING
Page 999 of 1501
2) Disconnect air intake hose and vacuum hoses. Remove air
hose and air outlet housing. Remove heat protectors. Disconnect
exhaust pipe. Remove power steering oil pump and bracket. Remove
engine hanger bracket. Disconnect oil inlet pipe.
3) Disconnect engine coolant hoses and tubes from
turbocharger. Remove exhaust manifold nuts and bolts. Remove exhaust
manifold and gaskets. Disconnect oil pressure and return pipes. Remove
turbocharger and exhaust manifold assembly. Separate turbocharger from
exhaust manifold.
Removal (3000GT - Front)
1) Disconnect negative battery cable. Drain engine oil and
coolant. Remove radiator. Disconnect exhaust pipe. Remove air intake
hose, air hoses and air pipe. Remove generator and belt. Remove oil
dipstick guide.
2) Remove heat protector. Disconnect front heated oxygen
sensor connector. Remove oil return pipe. Remove turbocharger support
bracket, and remove turbocharger from exhaust manifold.
Removal (3000GT - Rear)
1) Disconnect battery cables, and remove battery. Drain
engine oil and cooling system. Remove accelerator cable. Remove air
hose, air pipe and heat protectors. Disconnect clutch booster vacuum
hose. Remove air intake hoses and EGR pipe. Disconnect heated oxygen
sensor connectors.
2) Remove oil pipe and EGR valve. Disconnect exhaust fitting,
and remove rear heat protector. Remove oil return pipe. Remove
turbocharger assembly.
Inspection (All Models)
Check turbine and compressor wheels for cracking and other
damage. Ensure turbine and compressor wheels turn smoothly. Check for
oil leakage from turbocharger assembly. Check for proper wastegate
valve operation. See I - SYSTEM/COMPONENT TESTS article.
CAUTION: Apply light coat of oil to inner surface of flared area on
water pipe (flare nut fitting) before connecting to engine.
Installation (All Models)
1) To install, reverse removal procedure. Before oil pipe
flare nut (above turbocharger) is installed, pour clean engine oil
into turbocharger oil pipe installation hole. Ensure oil and air hoses
are properly installed and securely clamped.
2) Use NEW gaskets. Adjust accelerator cable (if necessary).\
Refill engine oil and coolant. Check for oil and coolant leaks.
Tighten all bolts to specification. See TORQUE SPECIFICATIONS.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE\
\
\
\
\
\
Applications Ft. Lbs. (N.m)
Coolant Pipe-To-Turbocharger Banjo Bolt .......... 31 (42)
EGR Valve ........................................ 16 (22)
Engine Coolant Temperature Sensor ................ 22 (30)
Exhaust Manifold-To-Engine Nuts ............ 18-21 (24-29)
Exhaust Manifold-To-Turbocharger Bolts ..... 40-47 (54-64)
Exhaust Pipe Bolts ......................... 21-36 (29-49)
Fuel Filter Line ................................. 27 (36)
Fuel Tank Drain Plug ....................... 11-18 (15-24)
Fuel Tank Nuts ............................. 15-21 (20-29)
Page 1045 of 1501
SCHEDULED SERVICES
1998 Mitsubishi Montero
1997-98 MAINTENANCE
Mitsubishi Maintenance & Service Intervals
Mitsubishi: Montero
* READ THIS FIRST *
Before preforming maintenance on vehicle, ensure that all
cautions and warnings have been observed to prevent vehicle damage or
personal injury. See CAUTIONS & WARNINGS in MAINTENANCE INFORMATION
article in this section.
Introduction
The frequency of scheduled inspection and maintenance
services in this article are based on "normal" vehicle usage. They DO
NOT take into account the following "severe" conditions:
* Driving In Dusty Conditions
* Trailer Towing, Police, Taxi, commercial Type Operation
* Extensive Idling, Driving In Stop-And-Go Traffic
* Short Trip Operation At Freezing Temperatures (Engine Not
Thoroughly Warmed Up)
* Driving In Sandy Areas
* Driving In Salty Areas
* More Than 50% Operation In Heavy City Traffic Or At Sustained
High Speeds During Hot Weather Above 90
F (32 C)
* Driving On Off-Road
If any of these severe conditions exist, the "normal" service
schedule frequency for some service items is inadequate and must be
supplemented. See the following section for specific details,
SEVERE SERVICE CONDITIONS/ACTIONS .
SEVERE SERVICE CONDITIONS/ACTIONS
The following table identifies eight "severe" conditions that
cause faster-than-normal wear. Each condition lists affected service
item(s) and their revised (more frequent) service interval.
If any severe condition(s) is applicable, its revised service\
interval(s) supersede those found in the "normal" schedules. Depending\
on the specific mileage/time, the revised interval(s) may overlap a
normal schedule (in which case they can be done together). If not, it
must be performed outside of the normal schedule.
SEVERE SERVICE CONDITIONS/ACTIONS TABLE
\
\
\
\
\
\
\
Condition Action Item Perform Every (1)
\b
\
\
\
\
\
\
\
Driving In Dusty Replace Engine Oil 3,000 Mile (4800 KM)
Conditions Or 3 Months
\b
\
\
\
\
\
Replace Oil Filter 6,000 Mile (9600 KM)
Or 6 Months
\b
\
\
\
\
\
Replace Air Cleaner 15,000 Mile (24,000 KM)
Filter
\b
\
\
\
\
\
Inspect Disk Brake 6,000 Mile (9,600 KM)
Pads Or 6 Months
Page 1046 of 1501
![MITSUBISHI MONTERO 1998 User Guide \b\
\
\
\
\
\
\
Trailer Towing Or Replace Engine Oil](/img/19/57333/w960_57333-1045.png "MITSUBISHI MONTERO 1998 User Guide \b\
\
\
\
\
\
\
Trailer Towing Or Replace Engine Oil")
\b\
\
\
\
\
\
\
Trailer Towing Or Replace Engine Oil 3,000 Mile (4800 KM)
Police, Taxi Or Or 3 Months
Commercial Type \b
\
\
\
\
\
Operation Replace Oil Filter 6,000 Mile (9600 KM)
Or 6 Months
\b
\
\
\
\
\
Replace Spark Plugs 15,000 Mile (24,000 KM)
\b
\
\
\
\
\
Replace Manual 30,000 Mile (48,000 KM)
Transmission
Oil
\b
\
\
\
\
\
Replace Transfer Oil 30,000 Mile (48,000 KM)
\b
\
\
\
\
\
\
\
Extensive Idling Replace Engine Oil 3,000 Mile (4800 KM)
Driving in Stop & Or 3 Months
Stop & Go Traffic
\b
\
\
\
\
\
Replace Oil Filter 6,000 Mile (9600 KM)
Or 6 Months
\b
\
\
\
\
\
\
\
Short-trip Replace Engine Oil 3,000 Mile (4800 KM)
Operation at Or 3 Months
Freezing \b
\
\
\
\
\
Temperatures Replace Oil Filter 6,000 Mile (9600 KM)
(Engine not Or 6 Months
thoroughly warmed)\b
\
\
\
\
\
Replace Spark Plugs 15,000 Mile (24,000 KM)
\b
\
\
\
\
\
\
\
Driving In Replace Air Cleaner 15,000 Mile (24,000 KM)
Sandy Areas Filter
\b
\
\
\
\
\
\
\
Driving In Inspect Disc Brake 6,000 Mile (9,600 KM)
Salty Areas Pads Or 6 Months
\b
\
\
\
\
\
\
\
More than 50 % Replace Engine Oil 3,000 Mile (4800 KM)
Operation in Heavy Or 3 Months
City Traffic Or \b
\
\
\
\
\
At Sustained High Replace Oil Filter 6,000 Mile (9600 KM)
Speeds During Hot Or 6 Months
Weather Above \b
\
\
\
\
\
90 F (32 C) Replace Manual 30,000 Mile (48,000 KM)
Transmission
Oil
\b
\
\
\
\
\
Replace Transfer Oil 30,000 Mile (48,000 KM)
\b
\
\
\
\
\
\
\
Driving On Replace Manual 30,000 Mile (48,000 KM)
Off-Road Transmission
Oil
\b
\
\
\
\
\
Replace Transfer Oil 30,000 Mile (48,000 KM)
\b
\
\
\
\
\
\
\
(
1) - Perform these services at the mileage or number of months
(since the last time), WHICHEVER COMES FIRST.
\f
\
\
\
\
\
\
\
7,500 MILE (12,000 KM) NORMAL SERVICE
7,500 MILE (12,000 KM) NORMAL SERVICE
Page 1047 of 1501
![MITSUBISHI MONTERO 1998 User Guide \
\
\
\
\
\
\
REPLACE](/img/19/57333/w960_57333-1046.png "MITSUBISHI MONTERO 1998 User Guide \
\
\
\
\
\
\
REPLACE")
\
\
\
\
\
\
\
REPLACE
\b
\
\
\
\
\
\
\
Engine Oil (
1)
\b
\
\
\
\
\
\
\
Engine Oil Filter (
2)
\b
\
\
\
\
\
\
\
(
1) - Change once a year or every 7500 miles (12,000 KM).
(
2) - If mileage is less than 7,500 miles (12,000 KM) each year,
replace the oil filter at every oil change.
\b
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\b
\
\
\
\
\
\
\
Material Condition Specification
\b
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Less Than SAE 5W-30
(
1) 0 F (-18 C) To 100 F (38 C)
\b
\
\
\
\
\
Ambient Temperature Above 0 F SAE 10W-30
(-18 C) To Over 100 F (38 C)
\b
\
\
\
\
\
\
\
(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if
the Ambient Temperature is above 0 F (-18 C).
\b
\
\
\
\
\
\
\
FLUID CAPACITIES
\b
\
\
\
\
\
\
\
Item Condition Specification (1)
\b
\
\
\
\
\
\
\
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1) \b \
\
\
\
\
Oil Filter 0.32 Qts. (0.3L)
\b
\
\
\
\
\
Oil Cooler 0.32 Qts. (0.3L)
\b
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\f
\
\
\
\
\
\
\
15,000 MILE (24,000 KM) NORMAL SERVICE
15,000 MILE (24,000 KM) NORMAL SERVICE\
\
\
\
\
\
\
INSPECT
\b
\
\
\
\
\
\
\
Disc Brake Pads (
3)
\b
\
\
\
\
\
\
\
Brake Hoses (
3)
\b
\
\
\
\
\
\
\
Drive Shaft Boots (
3)
\b
\
\
\
\
\
\
\
REPLACE
\b
\
\
\
\
\
\
\
Engine Oil (
1)
\b
\
\
\
\
\
\
\
Engine Oil Filter (
2)
\b
\
\
\
\
\
\
\
(
1) - Change once a year or every 7,500 miles (12,000 KM).
(
2) - If mileage is less than 7,500 miles (12,000 KM) each year,
replace the oil filter at every oil change.
(
3) - Or inspect every year.
\b
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
Page 1048 of 1501
![MITSUBISHI MONTERO 1998 User Guide \b\
\
\
\
\
\
\
Material Condition](/img/19/57333/w960_57333-1047.png "MITSUBISHI MONTERO 1998 User Guide \b\
\
\
\
\
\
\
Material Condition")
\b\
\
\
\
\
\
\
Material Condition Specification
\b
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Less Than SAE 5W-30
(
1) 0 F (-18 C) To 100 F (38 C)
\b
\
\
\
\
\
Ambient Temperature Above 0 F SAE 10W-30
(-18 C) To Over 100 F (38 C)
\b
\
\
\
\
\
\
\
Brake Fluid All DOT 3 Or DOT 4
\b
\
\
\
\
\
\
\
(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if
the Ambient Temperature is above 0 F (-18 C).
\b
\
\
\
\
\
\
\
FLUID CAPACITIES
\b
\
\
\
\
\
\
\
Item Condition Specification (1)
\b
\
\
\
\
\
\
\
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1) \b \
\
\
\
\
Oil Filter 0.32 Qts. (0.3L)
\b
\
\
\
\
\
Oil Cooler 0.32 Qts. (0.3L)
\b
\
\
\
\
\
\
\
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\f
\
\
\
\
\
\
\
22,500 MILE (36,000 KM) NORMAL SERVICE
22,500 MILE (36,000 KM) NORMAL SERVICE\
\
\
\
\
\
\
VERIFY
\b
\
\
\
\
\
\
\
Last Major Service Was Performed
\b
\
\
\
\
\
\
\
REPLACE
\b
\
\
\
\
\
\
\
Engine Oil (
1)
\b
\
\
\
\
\
\
\
Engine Oil Filter (
2)
\b
\
\
\
\
\
\
\
(
1) - Change once a year or every 7,500 miles (12,000 KM).
(
2) - If mileage is less than 7,500 miles (12,000 KM) each year,
replace the oil filter at every oil change.
\b
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
\b
\
\
\
\
\
\
\
Material Condition Specification
\b
\
\
\
\
\
\
\
Engine Oil Ambient Temperature Less Than SAE 5W-30
(
1) 0 F (-18 C) To 100 F (38 C)
\b
\
\
\
\
\
Ambient Temperature Above 0 F SAE 10W-30
(-18 C) To Over 100 F (38 C)
\b
\
\
\
\
\
\
\
(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if
the Ambient Temperature is above 0 F (-18 C).
\b
\
\
\
\
\
\
\
FLUID CAPACITIES
\b
\
\
\
\
\
\
\
Item Condition Specification (1)