parking brake MITSUBISHI MONTERO 1998 User Guide
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 230 of 1501
Fig. 10: Exploded View Of Parking Brake Assembly (Typical With Rear
Disc Brakes - Except Diamante)
Courtesy of Mitsubishi Motor Sales of America.
CAUTION: Shoe-to-anchor spring must be installed correctly for proper
functioning of parking brakes.
Installation
1) To install, reverse removal procedure. When installing
shoe-to-anchor spring, ensure spring is installed correctly. When
installing adjuster, install left adjuster with adjusting bolt facing
vehicle front and right adjuster with adjusting bolt facing vehicle
rear.
2) On models with ABS, ensure gap between rotor teeth and
speed sensor pole piece is 0.008-0.039" (0.20-1.00 mm).
Removal (3000GT)
1) Raise and support vehicle. Remove rear wheel(s).
Disconnect rear speed sensor. Remove rear disc brake calipers and
Page 231 of 1501
rotors. See REAR BRAKE CALIPER .
2) On FWD models, remove grease cap, hub nut and hub. On AWD
models, disconnect rear axle from companion flange at hub. Remove axle
hub nut. Using slide hammer and Hub Adapter (MB991354), remove axle
from knuckle.
3) On all models, remove adjusting wheel spring. Remove shoe
hold-down cup, spring and pin. Note how shoe-to-anchor spring is
installed, and then remove adjuster and shoe-to-anchor spring. Remove
strut and return spring. Remove clip and shoe and lining assembly.
CAUTION: Shoe-to-anchor spring must be installed correctly for proper
functioning of parking brakes.
Installation
To install, reverse removal procedure. When installing shoe-
to-anchor spring, ensure spring is installed correctly. When
installing adjuster, install left adjuster with adjusting bolt facing
vehicle front and right adjuster with adjusting bolt facing vehicle
rear. On AWD, tighten companion flange nut to 188-217 ft. lbs. (260-
300 N.m).
REAR DISC BRAKE PADS
NOTE: Replace inner and outer pads at same time.
Removal
Raise and support vehicle. Remove rear wheels, and disconnect
parking brake cable. Remove lower lock pin bolt. Lift caliper body
upward. Using a wire, support caliper aside. Remove inner shims, anti-
squeak shim and pad assembly from support mounting. Remove pad clips.
Installation
Rotate piston to align notches in piston projection on back
of pads (if equipped). Install retaining clips, pad assembly, inner
shims and anti-squeak shim onto support mounting. Lower caliper body,
and install lock pin.
REAR BRAKE CALIPER
Removal
Raise and support vehicle. Remove rear wheels. Disconnect
brake hose from caliper. Cap end of brake line to prevent spillage.
Remove upper and lower caliper mounting bolts. Lift caliper body
upward. Remove caliper.
Installation
To install, reverse removal procedure. Tighten bolts to
specification. See TORQUE SPECIFICATIONS . Bleed brake system. See
BLEEDING BRAKE SYSTEM .
REAR BRAKE ROTOR
Removal & Installation
Raise and support vehicle. Remove rear caliper. See
REAR BRAKE CALIPER . Remove rotor. To install, reverse removal
procedure.
REAR BRAKE DRUM & SHOES
Removal
1) Raise and support vehicle. Remove wheels. Remove brake
drum from hub. If drum is difficult to remove, back-off shoe adjuster
Page 232 of 1501
and remove drum. Remove shoe return springs and shoe hold-down
springs. See Fig. 11.
2) Disconnect parking brake cable from lever. Remove brake
shoes and adjuster assembly. Remove parking brake lever snap ring, and
disengage lever from brake shoe.
Fig. 11: Exploded View Of Rear Drum Brake Assembly (Montero Sport
Shown, Others Similar)
Courtesy of Mitsubishi Motor Sales of America.
Installation
1) To install, reverse removal procedure. Apply Lubriplate to
shoe-to-backing plate bosses, adjuster assembly threads and parking
brake lever pin.
2) Adjust shoes to lightly contact brake drum. See REAR BRAKE
SHOES under ADJUSTMENTS. Depress brake pedal to center shoes, and
check pedal travel. Rotate brake drum to ensure free movement.
Page 233 of 1501
WHEEL CYLINDERS
Removal & Installation
Raise and support vehicle. Remove rear brake drum and shoes.
See REAR BRAKE DRUM & SHOES . Remove wheel cylinder and seal assembly.
To install, reverse removal procedure. Bleed brakes. See
BLEEDING BRAKE SYSTEM .
MASTER CYLINDER
Removal
Drain brake fluid from master cylinder. Remove sensor
connector (if equipped). Disconnect brake lines from master cylinder,
and install plugs to prevent brake fluid spillage. Remove master
cylinder from booster and separate reservoirs from housing (if
necessary).
Installation
To install, reverse removal procedure. Before installation,
check and adjust clearance between back of master cylinder piston and
power brake push rod. See MASTER CYLINDER PUSH ROD under ADJUSTMENTS.
After installation, adjust pedal height. See BRAKE PEDAL HEIGHT & FREE
PLAY under ADJUSTMENTS. Bleed brake system.
POWER BRAKE BOOSTER
Removal
Remove brake master cylinder. See MASTER CYLINDER. Disconnect
vacuum hose from power brake booster. Disconnect clevis pin attaching
brake pedal to power brake booster push rod. From inside vehicle,
remove 4 nuts attaching power brake booster to firewall. Remove power
brake booster.
Installation
To install, reverse removal procedure. Install master
cylinder. Bleed brake system if necessary.
POWER BRAKE BOOSTER CHECK VALVE
NOTE: To test check valve before removal, see POWER BRAKE BOOSTER
under TESTING.
Removal & Installation
Remove vacuum hose with check valve from power brake booster.
Loosen hose clamp(s) and remove check valve from hose on Mirage and
Summit. On all models, coat end(s) of check valve with sealant before
installation. Install valve with arrow (identification mark) pointing
toward intake manifold. Install and secure hose clamp(s).
REAR AXLE BEARINGS & OIL SEAL
Removal (Montero & Montero Sport)
1) With disc or drum removed, disconnect brake line from
caliper or wheel cylinder. Disconnect parking brake cable end, and
remove cable attaching bolts. Remove brake backing plate, bearing case
and axle shaft as an assembly. If axle shaft binds, use slide hammer
and puller to remove.
2) Remove shims, "O" ring and snap ring. Retain shims for
installation. Secure axle shaft assembly in a vise, and remove one
retainer bolt from backing plate. Push bearing case completely to side
of dust cover. Place adhesive tape around edge of bearing case at
Page 244 of 1501
![MITSUBISHI MONTERO 1998 User Guide Disc Thickness (Minimum)
Front ................................................. .88 (22.4)\
Rear ................................................... .33 (8.4)\
Drum Inside Diameter (Maximum](/img/19/57333/w960_57333-243.png "MITSUBISHI MONTERO 1998 User Guide Disc Thickness (Minimum)
Front ................................................. .88 (22.4)\
Rear ................................................... .33 (8.4)\
Drum Inside Diameter (Maximum")
Disc Thickness (Minimum)
Front ................................................. .88 (22.4)\
Rear ................................................... .33 (8.4)\
Drum Inside Diameter (Maximum) ........................... 9.1 (231\
)
Hub End Play ............................................ .002 (.05)\
Master Cylinder Inside Diameter
With ABS .............................................. 1.0 (25.4)\
Without ABS ........................................... .93 (23.8)\
Pad Lining Thickness (Minimum) ........................... .08 (2.0\
)
Shoe Lining Thickness (Minimum) ......................... .039 (1.0\
)
Wheel Cylinder Inside Diameter ......................... .750 (19.1)\
\
\
\
\
\
\
\
BRAKE SPECIFICATIONS (GALANT) \
\
\
\
\
\
\
Application In. (mm)\
Booster Pushrod Clearance
Single Booster ............................... .024-.031 (.60-.80)\
Tandem Booster ............................... .016-.024 (.40-.60)\
Disc Runout ............................................. .003 (.08)\
Disc Thickness (Minimum) ................................ .88 (22.4\
)
Drum Inside Diameter (Maximum) ........................... 9.1 (231\
)
Hub End Play ............................................ .002 (.05)\
Master Cylinder Inside Diameter ......................... 1.0 (25.4)\
Pad Lining Thickness (Minimum) ........................... .08 (2.0\
)
Shoe Lining Thickness (Minimum) ......................... .039 (1.0\
)
Wheel Cylinder Inside Diameter ......................... .750 (19.1)\
\
\
\
\
\
\
\
BRAKE SPECIFICATIONS (MIRAGE) \
\
\
\
\
\
\
Application In. (mm)\
Booster Pushrod Clearance ...................... .026-.033 (.65-.85)\
Disc Runout ........................................... .006 (.0024)\
Disc Thickness (Minimum) ................................ .65 (16.4\
)
Drum Inside Diameter (Maximum) ........................... 8.1 (206\
)
Hub End Play ............................................ .002 (.05)\
Master Cylinder Inside Diameter ........................ .87 (22.22)\
Pad Lining Thickness (Minimum) ........................... .08 (2.0\
)
Shoe Lining Thickness (Minimum) ......................... .039 (1.0\
)
Wheel Cylinder Inside Diameter ......................... .750 (19.1)\
\
\
\
\
\
\
\
BRAKE SPECIFICATIONS (MONTERO) \
\
\
\
\
\
\
Application In. (mm)\
Booster Pushrod Clearance ...................... .026-.035 (.65-.90)\
Disc Runout
Front ................................................. .004 (.10)\
Rear .................................................. .003 (.08)\
Disc Thickness (Minimum)
Front ................................................. 1.0 (25.4)\
Rear .................................................. .65 (16.4)\
Hub End Play ........................................... .0098 (.25)\
Master Cylinder Inside Diameter ........................ .937 (23.8)\
Pad Lining Thickness (Minimum)
Front ................................................. 1.08 (2.0)\
Rear ........................................................ (1)
Parking Brake Drum Diameter (Maximum) .................. 7.795 (198\
)
Page 245 of 1501
![MITSUBISHI MONTERO 1998 User Guide (1) - Information not available from manufacturer. \
\
\
\
\
\
\](/img/19/57333/w960_57333-244.png "MITSUBISHI MONTERO 1998 User Guide (1) - Information not available from manufacturer. \
\
\
\
\
\
\")
(1) - Information not available from manufacturer. \
\
\
\
\
\
\
BRAKE SPECIFICATIONS (MONTERO SPORT) \
\
\
\
\
\
\
Application In. (mm)\
Disc Runout
Front ................................................. .002 (.06)\
Rear .................................................. .003 (.08)\
Disc Thickness (Minimum)
Front ................................................. .88 (22.4)\
Rear .................................................. .65 (16.4)\
Drum Diameter (Maximum) .............................. 10.71 (272.0\
)
Hub End Play (Maximum) .................................. .002 (.05\
)
Master Cylinder Inside Diameter ........................ .937 (23.8)\
Pad Lining Thickness (Minimum) .......................... 1.08 (2.0\
)
Shoe Lining Thickness (Minimum) ......................... .039 (1.0\
)
Wheel Cylinder Inside Diameter .......................... .90 (22.8)\
\
\
\
\
\
\
\
BRAKE SPECIFICATIONS (3000GT) \
\
\
\
\
\
\
Application In. (mm)\
Booster Pushrod Clearance ...................... .026-.030 (.65-.75)\
Disc Runout
Front
AWD ................................................. .004 (.10)\
FWD ................................................. .003 (.07)\
Rear ................................................ .003 (.08)\
Disc Thickness (Minimum)
Front
AWD ................................................ 1.12 (28.4)\
FWD ................................................. .88 (22.4)\
Rear
AWD ............................................... .72 (18.4)\
FWD ............................................... .65 (16.4)\
Hub End Play ............................................ .002 (.05)\
Master Cylinder Inside Diameter ......................... 1.0 (25.4)\
Pad Lining Thickness (Minimum) .......................... 1.08 (2.0\
)
Parking Brake Drum Diameter (Maximum) ................... 6.65 (169\
)
\
\
\
\
\
\
\
Page 260 of 1501
specified, bleed system and inspect hydraulic and clutch components.
See CLUTCH PEDAL SPECIFICATIONS table.
CLUTCH PEDAL INTERLOCK SWITCH
1) Place transmission in Neutral and apply parking brake.
Turn ignition switch to START position with clutch pedal not
depressed. Engine should not crank. If engine cranks, adjust or
replace interlock switch.
2) Disconnect interlock switch connector. Interlock switch
connector is located at clutch pedal. Depress and release interlock
switch. Using ohmmeter, check continuity between interlock switch
terminals. If continuity exists with interlock switch depressed and
does not exist with switch released, switch is okay. Adjust or replace
as necessary.
REMOVAL & INSTALLATION
CLUTCH ASSEMBLY
Removal (2WD Models)
1) Disconnect negative battery cable. Remove shift knob, dust
cover retaining plate, gaskets, stopper plate and control lever
assembly. Raise and support vehicle.
2) Remove front exhaust pipe. Drain transmission fluid. Index
mark drive shaft flange and remove drive shaft.
3) Disconnect back-up light switch connector, speedometer
cable connection and exhaust pipe mounting bracket. Remove lower
bellhousing cover. Disconnect clutch cable from clutch lever.
4) Support transmission with jack. Remove rear engine mount
nuts and bolts from transmission. Remove crossmember with rear engine
mount. Remove remaining bellhousing bolts, move transmission toward
rear and lower from vehicle.
5) If reusing pressure plate, index mark pressure plate to
flywheel for installation reference. Install a clutch alignment tool
to prevent pressure plate and clutch disc from dropping. Loosen
pressure plate bolts gradually in a crisscross pattern to avoid
warping pressure plate flange during removal. Remove pressure plate
and clutch disc. See Fig. 3.
Inspection
1) Check release bearing and release fork for damage or wear.
DO NOT clean release bearing assembly in solvent.
2) Inspect pressure plate surface for wear, cracks, and/or
discoloration. Measure diaphragm spring ends for wear and uneven
height. Replace assembly if height difference between fingers exceeds
.02" (.5 mm).
3) Check facing of clutch disc for loose rivets, uneven
contact, deterioration, seizure or oil saturation. Measure distance
from clutch disc surface to head of rivet. Replace clutch disc if
distance is less than .012" (.30 mm). Replace worn or defective
components as necessary. See Fig. 4.
CAUTION: Install clutch disc with manufacturer's stamp mark (located
near hub of clutch disc) toward pressure plate.
Installation
1) Using a clutch alignment tool, install pressure plate and
clutch disc. If reusing pressure plate, ensure index marks are
aligned. Tighten bolts evenly in a crisscross pattern to
specification. See TORQUE SPECIFICATIONS . See Fig. 3.
2) Clean release bearing sliding surface. DO NOT clean
Page 268 of 1501
COMPUTER RELEARN PROCEDURES
1998 Mitsubishi Montero
GENERAL INFORMATION
Computer Relearn Procedures
All Models
* PLEASE READ THIS FIRST *
The following general procedures are to be used if
driveability problems are encountered after power loss or battery has
been disconnected. These procedures may provide an aid in eliminating
these problems.
To reduce the possibility of complaints, after any service
which requires battery power to be disconnected, vehicle should be
road tested.
COMPUTER RELEARN PROCEDURES
Vehicles equipped with engine or transmission computers may
require a relearn procedure after vehicle battery is disconnected.
Many vehicle computers memorize and store vehicle operation patterns
for optimum driveability and performance. When vehicle battery is
disconnected, this memory is lost. The computer will use default data
until new data from each key start is stored. As computer memorizes
vehicle operation for each new key start, driveability is restored.
Vehicle computers may memorize vehicles operation patterns for 40 of
more key starts.
Customers often complain of driveability problems during
relearn stage because vehicle acts differently then before being
serviced. Depending on type and make of vehicle and how it is
equipped, the following complaints (driveability problems) may exist:
* Harsh Or Poor Shift Quality
* Rough Or Unstable Idle
* Hesitation Or Stumble
* Rich Or Lean Running
* Poor Fuel Mileage
These symptoms and complaints should disappear after a number
of drive cycles have been memorized. To reduce the possibility of
complaints, after any service which requires battery power to be
disconnected, vehicle should be road tested. If a specific relearn
procedure is not available, the following procedure may be used:
Automatic Transmission
* Set parking brake, start engine in "P" or "N" position.
Warm-up vehicle to normal operating temperature or until
cooling fan cycles.
* Allow vehicle to idle for one minute in "N" position. Select
"D" and allow engine to idle for one minute.
* Accelerate at normal throttle position (20-50%) until vehicle
shifts into top gear.
* Cruise at light to medium throttle.
* Decelerate to a stop, allowing vehicle to downshift, and use
brakes normally.
* Process may be repeated as necessary.
Manual Transmission
Page 370 of 1501
TESTING & INSPECTION
AXLE SHAFT END PLAY
Montero & Montero Sport
Using dial indicator, check axle shaft end play. End play
should be .010" (.25 mm). If end play is not within specification,
replace axle bearing. See AXLE SHAFT OVERHAUL under OVERHAUL.
AXLE TOTAL BACKLASH
1) Raise and support rear axle. Place transmission in
Neutral. Apply parking brake. Rotate drive shaft clockwise. Place
reference marks on pinion dust cover and differential housing.
2) Rotate drive shaft counterclockwise, and measure distance
between reference marks. Differential must be removed and backlash
adjusted if distance exceeds 0.2" (5 mm). See RING GEAR BACK-LASH
procedure under DIFFERENTIAL ASSEMBLY (LIMITED SLIP) under OVERHAUL.
LIMITED SLIP DIFFERENTIAL PRELOAD
1) Place transmission in Neutral. Block front wheels. Raise
one rear wheel off ground and remove wheel. Release parking brake.
2) Using torque wrench and axle puller adapter, measure
starting torque while rotating wheel in forward direction. See Fig. 1.
Differential must be repaired if torque is less than 18 ft. lbs. (25
N.m).
Fig. 1: Testing Limited Slip Differential Preload
Courtesy of Mitsubishi Motor Sales of America.
LOCKING DIFFERENTIAL (MONTERO)
Air Pump
Page 372 of 1501
AXLE SHAFT R & I
Removal (Montero & Montero Sport)
Block front wheels. Raise and support rear axle housing.
Remove brake caliper and rotor. See Fig. 3. Remove parking brake cable
attaching bolts. Remove connection for parking brake cable end from
rear brake assembly. Remove ABS speed sensor (if equipped). Unbolt
backing plate with bearing housing from rear axle housing. Using
Puller (MB990241) and Slide Hammer (MB990211), remove axle assembly.\
DO NOT damage oil seal. Remove "O" ring. Replace if necessary.
Installation
Install NEW oil seal in axle housing as needed. To install
axle assembly, reverse removal procedure.
Fig. 3: Exploded View Of Typical Axle Shaft
Courtesy of Mitsubishi Motor Sales of America.
Installation
1) Insert new "O" ring and shim of .04" (1.0 mm) thickness