service MITSUBISHI MONTERO 1998 Service Manual

knuckles steering linkage
Rack and pinion mounting Tighten all mounting
loose bolts
Rack and pinion out of See adjustment in
adjustment STEERING article
Tie rod end loose Tighten and check
steering linkage
Excessive Pitman shaft-to- Repair as necessary
ball nut lash









\









\









\









\









\









\









\







Poor Lack of lubricant in ball Lubricate and service
Returnability joint or linkage systems
Binding in linkage or ball See STEERING LINKAGE
joints and SUSPENSION article
Improper front end alignment See WHEEL ALIGNMENT
article
Improper tire pressure Inflate to proper
pressure
Tie rod binding Inflate to proper
pressure
Shaft seal rubbing shaft See STEERING COLUMN
article









\









\









\









\









\









\









\







Excessive Improper tire pressure Inflate to proper
Vertical Motion pressure
Tires, wheels or rotors Balance tires then
out of balance check wheels and
rotors
Worn or faulty shock Check and replace if
absorbers necessary
Loose tie rod ends or Tighten or replace if
steering necessary
Loose or worn wheel See SUSPENSION article
bearings









\









\









\









\









\









\









\







Steering Pulls Improper tire pressure Inflate to proper
to One Side pressure
Front tires are different Rotate or replace if
sizes necessary
Wheel bearings not See FRONT SUSPENSION
article
adjusted properly
Bent or broken suspension See FRONT SUSPENSION
components article
Improper wheel alignment See WHEEL ALIGNMENT
article

Reaction ring sticking See POWER STEERING GEAR
in housing head article
Steering pump internal See POWER STEERING PUMP
leakage article
Steering gear-to-column See STEERING COLUMN
misalignment article
Lack of lubrication in Service front suspension
linkage
Lack of lubrication in Service front suspension
ball joints









\









\









\









\









\









\









\







Increased Effort High internal pump leakage See POWER STEERING PUMP
When Turning article
Wheel Fast Power steering pump belt Adjust or replace if
Foaming, Milky slipping necessary
Power Steering
Fluid, Low Fluid Low fluid level Check and fill to
Level or Low proper level
Pressure
Engine idle speed to low Adjust to correct
setting
Air in pump fluid system See POWER STEERING PUMP
article
Pump output low See POWER STEERING PUMP
article
Steering gear See POWER STEERING GEAR
malfunctioning article









\









\









\









\









\









\









\







Wheel Surges Low fluid level Check and fill to proper
or Jerks level
Loose fan belt Adjust or replace if
necessary
Insufficient pump See POWER STEERING PUMP
pressure article
Sticky flow control valve See POWER STEERING PUMP
article
Linkage hitting oil pan Replace bent components
at full turn









\









\









\









\









\









\









\







Kick Back or Air in pump fluid system See POWER STEERING PUMP
Free Play article
Worn poppet valve in See POWER STEERING PUMP
steering gear article
Excessive over center See POWER STEERING GEAR
lash article
Thrust bearing out of See POWER STEERING GEAR
adjustment article

subtracted by the width measured at the front of the tires at about
spindle height. A positive figure would indicate toe-in and a negative
figure would indicate toe-out. If the distance between the front and
rear of the tires is the same, toe measurement would be zero. To
adjust:
1) Measure toe-in with front wheels in straight ahead
position and steering wheel centered. To adjust toe-in, loosen clamps
and turn adjusting sleeve or adjustable end on right and left tie
rods. See Figs. 2 and 5.
2) Turn equally and in opposite directions to maintain
steering wheel in centered position. Face of tie rod end must be
parallel with machined surface of steering rod end to prevent binding.
3) When tightening clamps, make certain that clamp bolts are
positioned so there will be no interference with other parts
throughout the entire travel of linkage.
Fig. 5: Wheel Toe-In (Dimension A Less Dimension B)
TOE-OUT ON TURNS
1) Toe-out on turns (turning radius) is a check for bent or
damaged parts, and not a service adjustment. With caster, camber, and
toe-in properly adjusted, check toe-out with weight of vehicle on
wheels.
2) Use a full floating turntable under each wheel, repeating
test with each wheel positioned for right and left turns. Incorrect
toe-out generally indicates a bent steering arm. Replace arm, if
necessary, and recheck wheel alignment.

STEERING AXIS INCLINATION
1) Steering axis inclination is a check for bent or damaged
parts, and not a service adjustment. Vehicle must be level and camber
should be properly adjusted. See Fig. 6.
2) If camber cannot be brought within limits and steering
axis inclination is correct, steering knuckle is bent. If camber and
steering axis inclination are both incorrect by approximately the same
amount, the upper and lower control arms are bent.
Fig. 6: Checking Steering Axis Inclination