bulb MITSUBISHI OUTLANDER 2010 2.G Owner's Manual

Vehicle care and maintenance
7-67
7
5. To install the bulb, perform the removal steps in reverse.
Rear combination lights
N00943700432
1. Remove the screws (A) that hold the light unit and remove
the light unit.
CAUTION
!

Handle halogen light bulb with care. The gas inside
a halogen light bulb is highly pressurized, so drop-
ping, knocking, or scratching a halogen light bulb
can cause it to shatter.


Never hold the halogen light bulb with a bare hand,
dirty glove, etc. The oil from your hand could cause
the bulb to break the next time the fog lights are
used.
If the glass surface is dirty, clean it with alcohol and
let it dry completely before installing the bulb.
BK0115300US.book 67 ページ ２００９年７月１６日　木曜日　午前９時１３分

7-68 Vehicle care and maintenance
7
2. Turn the socket and bulb assembly counterclockwise to
remove it.NOTE

The tail and stop light uses an LED instead of the bulb.
Check with an authorized Mitsubishi Motors dealer or a
repair facility of your choice when the light needs to be
repaired or replaced.3. Pull the bulb out of the socket.
B- Tail and stop light (LED) - cannot be replaced
C- Rear turn-signal light
BK0115300US.book 68 ページ ２００９年７月１６日　木曜日　午前９時１３分

Vehicle care and maintenance
7-69
7
4. To install the bulb, perform the removal steps in reverse.NOTE

When mounting the light unit, align the clips (D) on the
light unit with the hole in the body.
Back-up lights
N00929100041
1. Open the tailgate.
2. Insert a screwdriver into the notch of the cover and pry
gently to remove the cover.NOTE

Wrap a cloth around the tip of the screwdriver to keep
from scratching the cover.
BK0115300US.book 69 ページ ２００９年７月１６日　木曜日　午前９時１３分

7-70 Vehicle care and maintenance
7
3. Turn the socket (A) counterclockwise to remove it. 4. Pull the bulb out of the socket.
5. To install the bulb, perform the removal steps in reverse.
BK0115300US.book 70 ページ ２００９年７月１６日　木曜日　午前９時１３分

7-72 Vehicle care and maintenance
7
4. Remove the socket and bulb assembly (C) together by
turning it counterclockwise, and then remove the bulb by
pulling it out.
5. To install the bulb, perform the removal steps in reverse.
NOTE

When mounting the light unit, align the pins (D) on the
light unit with the hole in the body.
BK0115300US.book 72 ページ ２００９年７月１６日　木曜日　午前９時１３分

7-74 Vehicle care and maintenance
7
3. Pull the bulb out of the socket. 4. To install the bulb, perform the removal steps in reverse.
NOTE

When mounting the light unit, insert tab (C) first then
align tab (D) with its hole.
BK0115300US.book 74 ページ ２００９年７月１６日　木曜日　午前９時１３分

Vehicle care and maintenance
7-75
7
High-mounted stop light
N00943900102
NOTE

The high-mounted stop light uses an LED instead of the
bulb. Check with an authorized Mitsubishi Motors dealer
or a repair facility of your choice when the light needs to
be repaired or replaced.
Dome light (front)/Reading lights
N00944500251
1. Insert a screwdriver into the notch of the light assembly.
Gently pry to remove the lens.NOTE

Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.
BK0115300US.book 75 ページ ２００９年７月１６日　木曜日　午前９時１３分

7-76 Vehicle care and maintenance
7
2. While holding down the tab (A), pull out the bulb. 3. To install the bulb, perform the removal steps in reverse.
NOTE

Before replacing the bulb, put the dome light (front)/read-
ing lights switch into the “OFF” position.


When mounting the lens, align the tab (B) with the hole
on the vehicle body.
BK0115300US.book 76 ページ ２００９年７月１６日　木曜日　午前９時１３分

Vehicle care and maintenance
7-77
7
Dome light (rear)/ Cargo room light
N00944100316
1. Insert a screwdriver into the notch of the light assembly
and pry gently to remove the lens.NOTE

Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.2. While holding down the tab (A), pull out the bulb.
BK0115300US.book 77 ページ ２００９年７月１６日　木曜日　午前９時１３分

7-78 Vehicle care and maintenance
7
3. To install the bulb, perform the removal steps in reverse.NOTE

Before replacing the bulb, put the dome light (rear)/cargo
room light switch into the “OFF” position.


When mounting the lens, align the tabs (B) with the holes
on the vehicle body.
Glove compartment light
N00954200062
1. Turn the socket (A) counterclockwise to remove it.
BK0115300US.book 78 ページ ２００９年７月１６日　木曜日　午前９時１３分