Eco MITSUBISHI OUTLANDER 2013 3.G Owner's Manual

2-30 Seat and restraint systems
2
NOTE
When the seatback of a front seat is reclined, return it to
the upright position before driving.
Folding the second row seats
N00405700110
The second row seat can be folded to create an additional cargo
area or to permit access to the third row seat on vehicles with a
third row seat.NOTE
You can separately fold the right and left side of the sec-
ond row seat.

When folding down the seatback, the seat belt buckles can
be stowed in the slits on the seat to avoid leaving marks on
the seat.
“Storing the second row and third row seat belts” on page
2-46.To f o l d u p t h e s e a t1. Lower the head restraints to the lowest position.
Refer to “Head restraints” on page 2-26.
CAUTION
!
In the cargo area, do not load the luggage higher
than the top of the seats and make sure that the lug-
gage is firmly secured. Restricted rear vision or fly-
ing objects entering the passenger compartment
during sudden braking could result in a serious acci-
dent.
Seats should always be folded up and put back into
the normal position by an adult. Seat adjustments
by a child could lead to an unexpected accident.
When adjusting the seats, be careful not to catch
your hand or leg. Personal injury could result.
BK0150600US.book 30 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

2-32 Seat and restraint systems
2
For vehicles without 2nd row seat slide function, the seat-
back will fall forward. Lift the entire seat until you hear a
click.
4. After folding the seat, gently shake the folded seat to
make sure it’s firmly secured.
WA R N I N G
!
When folding the second row seat, make sure no one
is on the seat. The seatback will fall forward rapidly
and could cause serious injury.

To reduce the risk of serious or fatal injury, do not
allow the front passenger seat or seatback to remain
in contact with the folded second row seat. The front
passenger seat is equipped with weight sensors.
Depending on the weight detected, the front passen-
ger airbag is disabled or enabled.
When folding the second row seats forward for
increased cargo capacity, the front passenger seat
and seatback must be adjusted to assure they are not
contacting the second row seat. In the event the
front seat or seatback is allowed to contact the
folded second row seat, proper operation of the front
passenger airbag system may be affected.
Never let persons or cargo sit on top of the folded
seat. Doing so could damage the seat.
WA R N I N G
!
BK0150600US.book 32 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

Seat and restraint systems
2-33
2
To put the seat back in its normal position1. While supporting the seat with your hand, pull the lock
release strap (A) on the backside of the seat cushion and
keep it pulled as you lower the seat flat.
CAUTION
!
For vehicles equipped with a third row seat, be care-
ful not to catch the feet of any passengers sitting in
the third row seat, when returning the second row
seats to their original position.
BK0150600US.book 33 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

Seat and restraint systems
2-35
2
5. Raise all the head restraints to the highest position.
Refer to “Head restraints: Adjustment of the head restraint
height” on page 2-26.
Making a flat seat
N00404800156
The entire interior of the vehicle may be used for sleeping
accommodations by removing the head restraints and fully
reclining all the seats when the vehicle is stopped.
WA R N I N G
!
After returning the seat to its normal position, raise
all the head restraints to the highest position. Using
the second row seat with the head restraints
retracted could cause a serious head injury or death
in the event of a collision or sudden breaking.
WA R N I N G
!
Never drive with passengers or cargo on the flat
seat. This is extremely dangerous and can cause
severe or fatal injury or death in an accident or if
heavy braking is required.
CAUTION
!
Adjust the seats only when the vehicle is stopped in a
safe place.
Seat should be adjusted only by adults to avoid acci-
dents.
When sliding the seats, be careful not to catch your
hand or leg.
Do not walk around on top of the seats after they
have been laid flat because the footing is uneven. It
is safest to move about on your hands and knees.
To ensure the seats are locked securely, attempt to
move them back and forth.
Do not jump on or drop heavy objects on the seat-
backs.
BK0150600US.book 35 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

2-36 Seat and restraint systems
2
1. Remove the head restraints from the front seats and raise
the arm rest on the second row seats.
For vehicles with a cargo area cover, remove the cover.
(Refer to “Head restraints” on page 2-26, “Arm rest” on
page 2-11 and “Cargo area cover” on page 3-288.)

To raise the seatback, firmly place your hand on the
seatback, pull the seatback lock knob up, and raise
the seatback slowly. (Refer to “To adjust the seat-
back” on page 2-8 and page 2-13.) Do not let chil-
dren adjust the seatback.
CAUTION
!
BK0150600US.book 36 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

Seat and restraint systems
2-37
2
2. Slide the second row seats back as far as possible (vehi-
cles with second row seat slide function).
(Refer to “To adjust the seat forward or backward” on
page 2-13.)3. Slide the front seats fully forward, then recline their seat-
backs backward to achieve a flat surface.
(Refer to “To adjust the seat forward or backward” on
page 2-7 and “To adjust the seatback” on page 2-8.)
BK0150600US.book 37 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

2-38 Seat and restraint systems
2
4. Recline the seatbacks of the second row seats.
(Refer to “To adjust the seatback” on page 2-13.)5. The flat seat configuration is now complete.
To return the seats to the normal position, reverse the
above procedure.
BK0150600US.book 38 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

Seat and restraint systems
2-43
2
NOTE
With the exception of the seat belt for the driver, the seat
belts in all other seating positions are equipped with an
Automatic Locking Retractor (ALR) function. If you pull
the seat belt fully out of the retractor, the retractor will
switch to its ALR child restraint installation function (see
page 2-57).
When the ALR function has been activated, the seat belt
will only retract. If this happens, let the belt fully retract,
then pull the seat belt back out, repeating steps 1 through
4.
5. To release the belt, press the button on the buckle and
allow the belt to retract.
If the belt does not retract smoothly, pull it out and check
for kinks or twists in the webbing. Then make sure it
remains untwisted as it retracts.
Driver’s seat belt reminder/warning light and
display
N00418400313
Warning light
Warning display type 1
Warning display type 2
A tone and warning light are used to remind the driver to fasten
the seat belt.
If the ignition switch is set to the “ON” position without the
driver’s seat belt being fastened, a warning light will come on
and a tone will sound for approximately 6 seconds to remind
you to fasten your seat belt.
If you then drive with the seat belt unfastened for longer than a
minute from when the ignition switch was turned on, the warn-
ing light will come on and blink repeatedly and the tone will
sound intermittently.
The warning light and the tone will stop after approximately 90
seconds.
WA R N I N G
!
Be sure the lap belt portion fits snugly and is worn
as low as possible across the hips, not around the
waist. Failure to follow this instruction will increase
the risk of serious injury or death in the event of an
accident.
Be sure the seat belt webbing is not twisted when
worn. Twisted webbing may adversely affect seat
belt performance.
BK0150600US.book 43 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

2-44 Seat and restraint systems
2
If you then repeatedly stop and start your vehicle with the seat
belt unfastened, the warning light/display and tone will remind
you to fasten your seat belt every time the vehicle starts mov-
ing. You will also be reminded to fasten your seat belt in this
way when you remove your seat belt while driving. The warn-
ing light and the tone go off when the seat belt is fastened.NOTE
At the same time, “FASTEN SEAT BELT” will be dis-
played on the information screen in the multi-information
display.
Front passenger seat belt warning light
N00418300208
The front passenger seat belt warning light is located in the
instrument panel.
When the ignition switch is turned to the “ON” position, this
indicator normally comes on and goes off a few seconds later.
The light comes on when a person sits on the front passenger
seat but does not fasten the seat belt. It goes off when the seat
belt is subsequently fastened.
WA R N I N G
!
In order to reduce the risk of serious injury or death
in an accident, always fasten your own seat belt. Do
not allow anyone to ride in your vehicle unless he or
she is also seated and fastening a seat belt. Children
should additionally be restrained in a secure child
restraint system.
WA R N I N G
!
Do not install any accessory or sticker that makes
the light difficult to see.
BK0150600US.book 44 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

2-46 Seat and restraint systems
2
Storing the second row and third row seat belts
N00406500098
When a second row seat belt (except for the center seat belt) or
a third row seat belt is not in use, store it as shown in the illus-
tration.Store the second row and third row seat belt webbing in the clip
slot (C) and the latch plate in the slot (D) as shown in the illus-
tration.A- Second row seat belt
B- Third row seat belt (Seating 7 passengers)BK0150600US.book 46 ページ ２０１２年３月３０日　金曜日　午前１０時４３分