keyless entry MITSUBISHI OUTLANDER 2020 (in English) User Guide

Keyless entry system (if so equipped)
Features and controls 5-11
5
 To use the new remote control transmitters, it is necessary to register the key with both theelectronic immobilizer
and keyless entry sys-
tem. Also refer to “Electr
onic immobilizer (Anti-
theft starting system): Customer key pro-gramming” on page 5-6.NOTE
BK0278200US.book 11 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Keyless entry system (if so equipped) 5-12 Features and controls
5
N00596500041
You can change the settings for the follow
ing functions according to your preferences.
When changing a setting, perform the fol
lowing steps.
1. Remove the key from
the ignition switch.
2. Open the driver’s door and turn the combination
headlights and dimmer switc
h to the “OFF” position.
3. Complete steps i to iv of the procedure. Step
s ii to iv should be completed within 8 seconds.
Customizing the keyless entry system

Item
Ste p i
Ste p i i
Step iii
Ste p i v
Notification
Horn deactiva- tion/reactivation
Press and hold the LOCK button (1) for 4 to 8 seconds.
While holding the LOCK button (1), press the UNLOCK button (2).
While holding the LOCK button (1), release the UNLOCK button (2).
Release the LOCK but- ton (1).
Chimes  Page 5-8
Turn signal lights deactivation/reac- tivation
Press and hold the UNLOCK button (2) for 4 to 8 seconds.
While holding the UNLOCK button (2), press the LOCK button (1).
While holding the LOCK button (1), release the UNLOCK button (2).
Release the LOCK but- ton (1).
Chimes  Page 5-8
Setting the door and liftgate unlock function
Press and hold the LOCK button (1) for 4 to 8 seconds.
While holding the LOCK button (1), press the UNLOCK button (2).
While holding the UNLOCK button (2), release the LOCK button (1).
Release the UNLOCK button (2).
Chimes  Page 5-8
BK0278200US.book 12 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Keyless entry system (if so equipped)
Features and controls 5-13
5
N00546101124
Your keyless entry system operates on a radio frequency subject to
Federal Communica-
tions Commission (FCC)
Rules (For vehicles
sold in U.S.A.) and Industry Canada Rules (For vehicles sold in Canada). This device complies with Part 15 of FCC Rules andIndustry Canada licenc
e-exempt RSS stan-
dard(s). Operation is subject to the following two con-ditions.  This device may not
cause harmful inter-
ference.  This device must ac
cept any interference
received, including interference that may cause undesired operation.
N00544101247
1. Before replacing the battery, remove staticelectricity from your body by touching a metal grounded object.
NOTE
 Be sure to press the buttons correctly wh
en performing the procedures. If you perform
the procedures incorrectly, the registere
d ID code information could
be deleted or the settings
could be changed uninten
tionally. If the registered ID code info
rmation is deleted, register the rem
ote control transmitters again.
Refer to “Customer remote control tr
ansmitter programming (Except for vehicl
es sold in Canada)” on page 5-9.
General information

CAUTIONChanges or modifica
tions not expressly
approved by the manufacturer for compli- ance could void the user’s authority to oper-ate the equipment.
Procedure for replacing the remote control transmitter bat-tery
WA R N I N G Do not swallow a coin type battery.• This product contains coin type battery. If a coin type battery is swallowed, it can cause severe internal burns and can lead to death.There have been case
s where a swallowed
battery has caused severe internal burns in just 2 hours.• Keep new and used batteries away fromchildren.• If the remote control transmitter casedoes not close securely, stop using theproduct and keep it away from children.• If you think batter
ies might have been
swallowed or placed in
side any part of a
person’s body, seek immediate medical attention.
 To prevent that can result in an explosion or the leakage of fl
ammable liquid or gas.
• Do not replace an
incorrectly battery.
Replace only with th
e same or equivalent
type.• Do not dispose of a battery into fire orincinerator, or mech
anically crushing or
cutting of a battery.• Do not use, store in or bring into a bat-tery where it may be exposed to extremely high temperature or extremelylow air pressure.CAUTION When the remote control transmitter case is opened, be careful to keep water, dust, etc.out. Also, do not touch the internal compo- nents. Dispose of used battery according to regula- tions for the disposal of battery.WA R N I N G
BK0278200US.book 13 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Keyless entry system (if so equipped) 5-14 Features and controls
5
2. Remove the screw (A) from the remote control transmitter. 3. With the Mitsubishi mark facing you, insert the cloth-cov-ered tip of a flat blade screwdriver into the notch in the remote control transmitter case and use it to openthe case.
4. Remove the used battery.
5. Install a new battery with the +side (B) up. 6. Close the remote control transmitter case firmly. 7. Attach the screw (A) removed in step 2. 8. Check the keyless entry system to see thatit works.
NOTE
 Be sure to perform the procedure with the Mitsubishi mark facing you. If the Mitsubi-shi mark is not facing you when you open theremote control transmitter case, the buttons may come out.  The Federal Communications Commission (FCC) ID number, the Industry Canada (IC) number and the model
number (radio certifi-
cation) are indicated in
the illustrated posi-
tion.
NOTE
 You may purchase a replacement battery at an electric appliance store.  An authorized Mitsubishi Motors dealer can replace the battery for you if you prefer.
+ side - side Coin type bat- tery CR1620
BK0278200US.book 14 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped)
Features and controls 5-15
5
N00503101222
The Free-hand Advanced Security Transmit- ter (F.A.S.T.-key) enables the doors and theliftgate to be locked
and unlocked, the engine
to be started and the operation mode to be changed simply by carrying it. The F.A.S.T.-key can also be used as the remote control transmitter of the keylessentry system. Refer to “Free-hand
Advanced Security
Transmitter (F.A.S.T.-key): Keyless entrysystem” on page 5-31.
The operations possible with the F.A.S.T.- key can be modified as stated below. (Keyless entry operations are possible.) For details, contact an
authorized Mitsubi-
shi Motors dealer. • Enabling only the locking and unlocking of the doors and the liftgate• Enabling only the starting of the engine • Deactivating the F.A.S.T.-key
Free-hand Advanced Secu- rity Transmitter (F.A.S.T.-key)
(if so equipped)
The F.A.S.T.-key must be carried by the driver. The F.A.S.T.-key is required for vehicle operations su
ch as locking and
unlocking the doors and the liftgate, starting the engine
and changing the
operation mode. When
leaving the vehi-
cle, make sure you are carrying the F.A.S.T.-key and then lock the vehicle.
WA R N I N G Individuals who use
implantable pace-
makers or implanta
ble cardiovascular-
defibrillators should keep away from theexternal and internal
transmitters. The
electromagnetic w
aves used in the
F.A.S.T.-key may affe
ct the operation of
implantable pacemakers and implantable cardiovascular-defibrillators.A- External transmitter B- Internal transmitter
WA R N I N G Individuals using ot
her electro-medical
apparatus besides implantable pacemak-ers and implantable
cardiovascular-defi-
brillators should
check with the
manufacturer of the apparatus to confirm the effect of the el
ectromagnetic waves
used by the F.A.S.T.-key. The electromag- netic waves may affect
the operations of
the electro-medical apparatus.NOTE
 The F.A.S.T.-key uses weak electromagnetic waves.In cases such as the following, operationmay be imprope
r or unstable.
• The vehicle is near a facility that emits strong electroma
gnetic waves, such as a TV
transmitting tower, a po
wer station, a radio
station or an airport
BK0278200US.book 15 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Free-hand Advanced
Security Transmitter (F.A.S
.T.-key) (if so equipped)
5-16 Features and controls
5
N00503201249
When a person enters the operating range of the F.A.S.T.-key while carrying the F.A.S.T.-key and presses the driver’s or front passen- ger’s door lock/unlock switch, the liftgate LOCK switch or the liftgate OPEN switch,verification of the ID
code is performed.
The doors and the liftgate can be locked and unlocked and the engine
can be started only
when the ID codes of the vehicle and F.A.S.T.-key match.
The operating range is
within about 2.3 feet
(70 cm) of the handles of the driver’s door,front passenger door and liftgate.
• The key is carried together with other com- munication devices such
as cellular phones
or radios, or electrical appliances such ascomputers • The F.A.S.T.-key touches or is covered by a metal object • A keyless entry system is being used nearby • The battery of the F.A.S.T.-key is run down• The vehicle is in
a location with strong
electromagnetic
waves or noise
Use the emergency key to lock and unlock the driver’s door in such circumstances.Refer to “To operate
without using the
F.A.S.T.-key” on page 5-29.  The F.A.S.T.-key is constantly performing reception opera
tions in its communication
with the vehicle. This means that the batteryis always running down, regardless of how often the F.A.S.T.-key is used. The battery life is approximately
1 to 3 years, depending
on the usage conditions.  Since the F.A.S.T.-key is constantly perform- ing reception operati
ons, the reception of
strong electrom
agnetic waves
can accelerate
the running down of the ba
ttery. Do not place
near to electrical appliances such as televi- sions or computers.NOTE
Operating range of the F. A . S . T. - k e y

NOTE
 When the battery of the F.A.S.T.-key has run down or there are st
rong electromagnetic
waves or noise in the area, the operating range could decrease
or operations could
become unstable.
Operating range for locking and unlocking the doors and the lift-gate
* : Front of the vehicle : Operating range
NOTE
 The door or liftgate switch can only be used for locking or unlocking when a matching F.A.S.T.-key is detected.  The system may not operate if the F.A.S.T.- key is too close to the windshield, door win-dows or liftgate.
BK0278200US.book 16 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped)
Features and controls 5-21
5
N00568101137
After approximately 30
minutes has elapsed
with the operation mode
in ACC, the function
automatically cuts out the power for the audio system and other electr
ic devices that can be
operated with that mode.When the engine switch is pressed while the operation mode is in AC
C, the power is sup-
plied again to those devices.
CAUTION When the engine is not running, put the oper- ation mode in OFF. Leaving the operationmode in ON or ACC for a long time whenthe engine is not running may cause the bat- tery to be discharged, making it impossible to start the engine. When the battery is disconnected, the current operation mode is memo
rized. After recon-
necting the battery, the memorized mode is selected automaticall
y. Before disconnect-
ing the battery for re
pair or replacement,
make sure to put the operation mode in OFF. Be careful if you are not sure which opera- tion mode the vehicle is in when the batteryis run down. The operation mode cannot be changed from OFF to ACC or ON if the F.A.S.T.-key is not detected to be in the
vehicle. Refer to “Oper-
ating range for star
ting the engine and
changing the operation mode” on page 5-17. When there is the F.A.S.T.-key in the vehicle and the operation mode
is not changed, the
battery in the F.A.S.T.-key may have worn out.Refer to “Warning acti
vation” on page 5-22.
NOTE
If the operation mode
cannot be changed to
OFF, perform the following procedure. 1. Move the selector lever to the “P” (PARK) position, and then change the operation mode to OFF.
2. One of the other causes could be low bat- tery voltage. If this
occurs, the keyless
entry system, the F.A.S.T.-key operationand steering wheel lock (if so equipped) will also not operate. Contact an authorized Mitsubishi Motorsdealer.
ACC power auto-cutout function

NOTE
 It is possible to modify functions as follows: • The time until the power cuts out can be changed to approximately 60 minutes. • The ACC power auto
-cutout function can
be deactivated.NOTE
For details, we reco
mmend you to consult an
authorized Mitsubish
i Motors dealer.
On vehicles equipped with the Smartphone-link Display Audio (SDA
), screen operations
can be used to make the adjustment. Refer to the separate owner’s manual fordetails.NOTE
BK0278200US.book 21 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped)
Features and controls 5-31
5
7. Release in sequence the LOCK and UNLOCK buttons within 8 seconds ofpressing the LOCK button in step 6. The immobilizer display on the information screen in the multi-information displaywill blink. (Perform
the following step
within 20 seconds.) When registration of ID code is complete, the buzzer will s
ound 3 times and the
immobilizer display will come on for 30 seconds. If an error occurs, F.A.S.T.-key program-ming will be terminated and the buzzer will sound for 3 seconds. 8. If you wish to register another F.A.S.T.- key, repeat the proc
ess from step 1 after
the operation mode is put in OFF. 9. When all F.A.S.T.-keys are registered, remove the F.A.S.T.-key from the keyslot.
N00515501412
Press the remote control transmitter buttonsto lock or unlock the doors and the liftgate.It can also help you signal for attention by setting off the panic alarm.
Press the LOCK button (1) to lock all the doors and the liftgate. The turn signal lights
will also blink once.
Press the UNLOCK button (2) to unlock the driver’s door only.
NOTE
 F.A.S.T.-key programming will be termi- nated if the operation mode is put in OFF before the immobilizer
display starts blink-
ing.
NOTE
 The immobilizer displa
y will go off immedi-
ately if the operation
mode is put in OFF.
 Perform the operation when the interrupt dis- play screen is not show
ing. The interrupt dis-
play screen may prevent you from seeing theimmobilizer display.  It is not possible to register a F.A.S.T.-key if the immobilizer displa
y goes off during the
procedure.
Keyless entry system

1-
LOCK ( ) button
2-
UNLOCK ( ) button
3- Power liftgate button (if so equipped) 4- PANIC button 5- Operation indicator light
NOTE
 On vehicles equipped wi
th the mirror retrac-
tor switch, the outside rearview mirrors auto- matically retract or extend when the doors and the liftgate are locked or unlocked usingthe remote control transmitter buttons. Refer to “Features and controls: Outside rearview mirrors” on page 5-63.
To l o c k

NOTE
 If you press the LOCK button (1) twice, the horn will sound once.
To u n l o c k

BK0278200US.book 31 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Free-hand Advanced
Security Transmitter (F.A.S
.T.-key) (if so equipped)
5-32 Features and controls
5
Within approximately 2 seconds, press the UNLOCK button one more time to unlock allthe doors and liftgate. The dome light will turn on for 30 seconds. The turn signal lights will also blink twice.The front side-marker and parking lights will also turn on for approximately 30 seconds. Refer to “Welcome light” on page 5-207.
N00544501140
The horn and turn signal lights of the keylessentry system answerback function can be changed as required. This is done with the operation mode in OFF.
N00597200058
The answerback function can be set in thefollowing three ways.Each time the answerback function is set, a chime will sound to tell you the condition of the answerback function. To change the settings, refer to “Customizing the Free-hand Advanced Security Transmitter(F.A.S.T.-key)” on page 5-34.
N00597300059
The answerback function from the turn signallights can be turned ON or OFF separately. Each time the answerback function is set, a chime will sound to
tell you the condition of
the answerback function. To change the settings, refer to “Customizing the Free-hand Advanced Security Transmitter (F.A.S.T.-key)” on page 5-34.
N00597400050
The buzzer answerback function can beturned ON or OFF as required.
NOTE
 If the UNLOCK button (2) is pressed and no doors or the liftgate are opened within approximately 30 seconds, the doors and the liftgate will automatically re-lock.On a vehicle equipped
with the Smartphone-
link Display Audio (SDA), the functions can be adjusted on the scre
en. For details, refer
to the separate owner’s manual.  The door and liftgate
unlock function can be
set so that all doors a
nd liftgate unlock when
the UNLOCK button (2) is pressed once. Refer to “Setting of door
and liftgate unlock
function” on page 5-33.
Answerback function

NOTE
 On a vehicle equipped
with the Smartphone-
link Display Audio (SDA
), the functions can
be adjusted on the screen. For details, referto the separate owner’s manual.

Horn deactivation/reactivation Number of chimes
Condition
One chime The horn will not sound. Two chimes The horn will sound. Four chimes
The horn will sound if the- LOCK button (1) is pressed twice within 1 second.

Turn signal lights deactivation/reac- tivation Number of chimes
To l o c k
To unlock
One chime One flash Two flashes Two chimes One flash No flash Three chimes No flash Two flashes Four chimes Two flashes One flash Five chimes No
flash One flash
Six chimes Two flashes No flash Seven chimes No flash No flash
Buzzer deactivation/reactivation
BK0278200US.book 32 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped)
Features and controls 5-33
5
N00544601271
The door and liftgate unlock function can be set to the following two conditions. Each time the door and
liftgate unlock func-
tion is set, a chime will
sound to tell you the
condition of the door and liftgate unlock function. To change the settings, refer to “Customizing the Free-hand Advanced Security Transmitter(F.A.S.T.-key)” on page 5-34.
N00579500020
After unlocking the doors and the liftgate, the power liftgate can be operated by pressing the power liftgate button (3).Refer to “Power lift
gate” on page 5-42.
N00544701142
If you are near your vehicle and feel threat- ened, you can activate the alarm to call atten- tion as follows: 1. Press the PANIC button (4) for more than 1 second. 2. The headlights will blink on and off and the horn will sound intermittently forapproximately 3 minutes. 3. To turn off the alarm, press any button on the remote control transmitter.
Setting the door and liftgate unlock function

Number of chimes
Condition
One chime [Factory setting]
When the UNLOCK button, driver’s or front passenger’s door lock/unlock switch, or liftgate OPEN switch is pressed one time, all doors and the liftgate unlock.
Tw o chimes
When the UNLOCK button or the driver’s door lock/unlock switch is pressed one time, only the driver's door unlocks.When the UNLOCK button or the driver’s door lock/unlock switch is pressed two times in succession, all doors and the liftgate unlock.
Operating the power liftgate

Using the panic alarm

NOTE
 The indicator light (5) comes on each time a button is pressed.  The F.A.S.T.-key can be used from approxi- mately 40 feet (12 m) away. However, this distance may change if
your vehicle is near a
TV transmitting tower, a power station, or a radio station.
 If the following conditions are observed after pressing the LOCK (1) or UNLOCK (2) but-ton on the remote control transmitter, thebattery in the F.A.S.T.-key may need to be replaced. • The doors and the liftgate cannot be locked or unlocked. • The panic alarm
cannot be operated.
• The indicator light
(5) is dim or does not
come on.
 If you lose your F.A.S.T.-key, please contact an authorized Mitsubishi Motors dealer for a replacement.  If you wish to obtain an additional F.A.S.T.- key, please contact an
authorized Mitsubishi
Motors dealer. A maximum of four F.A.S.T.-key can be programme
d for your vehicle.
 To use the new remote control transmitters, it is necessary to register
the key with both the
electronic immobilizer
and keyless entry sys-
tem.Also refer to “Electronic immobilizer (Anti- theft starting system): Customer F.A.S.T.- key programming” on page 5-30.NOTE
BK0278200US.book 33 ページ ２０１９年４月１０日　水曜日　午前１０時５９分