child seat MITSUBISHI OUTLANDER III 2018 User Guide

Seat belt use during pregnancy
Seat and restraint systems 4-25
4
Put the seat belt webbing in the back slot (A)on the clip and insert the metal plate of thelatch plate into the front slot (B) as shown inthe illustration.
N00406701202
If your seat belt is not long enough, evenwhen fully extended,
a seat belt extender
must be obtained. The extender may be usedfor either of the front seats.
N00406800134
Seat belts work for everyone, including preg-nant women. Like a
ll occupants, pregnant
women are more likely to be seriously injuredor killed in an accident if they do not wearseat belts.
N00417701710
The driver’s and front passenger’s seats eachhave a seat belt
equipped with a pre-tensioner
system and force limiter system.
Seat belt extender
WA R N I N GThe extender should only be used if theexisting belt is not long enough. Anyonewho can use the standard seat belt shouldnot use an extender. Unnecessary use of anextender can adversel
y affect seat belt
performance in an accident.When not required, the extender must beremoved and stowed.
Seat belt use during preg-nancy
WA R N I N GTo reduce the risk of serious injury ordeath to pregnant women and unbornchildren in an accident, pregnant womenshould always wear
a seat belt. The lap
portion of the seat belt should be wornsnug and low across the hips and belowthe rounding. Consult your doctor if youhave any additional qu
estions or concerns.
Seat belt pre-tensioner and force limiter systems
BK0249100US.book 25 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems
Seat and restraint systems 4-27
4
N00408701147
This warning light tells you if there is a prob-lem involving the SRS airbags and/or the seatbelt pre-tensioner system. Refer to “SRSwarning light/display” on page 4-41.
N00408900126
In the event of an accident, the seat belt forcelimiter system will help reduce the forceapplied to the driver a
nd front seat passenger.
N00407101740
When transporting infants or small childrenin your vehicle, an appr
opriate child restraint
system must always be
used. This is required
by law in the U.S. and Canada.Child restraint systems specifically designedfor infants and small children are offered byseveral manufacturers. Choose only a childrestraint system with a label certifying that itcomplies with Federal Motor Vehicle SafetyStandard 213 (FMVSS 213) or Motor VehicleRestraint Systems and
Booster Seats Safety
Regulations (RSSR).
Look for the manufac-
turer’s statement of compliance on the boxand child restraint system itself.
The child restraint system should be appropri-ate for your child’s we
ight and height, and
should properly fit your vehicle’s seat.For detailed information,
refer to the instruc-
tion manual accompanying the child restraintsystem.All children should be properly restrained ina restraint device that offers the maximumprotection for their size and age.Be sure to check local,
state, or provincial
requirements for child size and age that mayvary from the recommendations listed below.Children less than 1 year old and whoweigh 22 pounds (10 kg) or less MUSTride in a rear-facing child safety seat thatMUST ONLY be used in the second rowseat.Children older than 1 year of age and whoweigh less than 40 pounds (18 kg) or whoare less than 40 inches (100 cm) tall mustbe in a forward-facing restraint used onlyin the rear seat.
Children who weigh more than 40 pounds(18 kg) or who are more than 40 inches(100 cm) tall, regardless of age, shoulduse a suitable child seat or a booster seatin the rear seat until the vehicle’s lap-and-shoulder belt fits
them properly.
SRS warning Force limiter system Child restraint systems
Guidelines for child restraint system selection
WA R N I N GAll children must be seated in the rearseat, and properly restrained.Accident statistics
show that children of
all sizes and ages are safer when properlyrestrained in the rear seat, rather than inthe front seat.Be sure to select a child restraint systemthat is appropriate not only for the child’ssize and age but also for your vehicle.Some child restraint systems may not fityour vehicle properly.
BK0249100US.book 27 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems4-28 Seat and restraint systems
4
Any child who is too large to use a childrestraint system should ride in the rearseat and wear the la
p-and-shoulder belt
properly. The shoulder belt must be posi-tioned over the shou
lder and across the
chest, not across their neck, and with thelap belt positioned low on the child’s hips,not across their stomach. If necessary, abooster seat should be
used to help achieve
a proper seat belt fi
t. Follow the booster
seat manufacturer’s instructions. Only usea booster seat that is
certified as comply-
ing with Federal Motor Vehicle SafetyStandards or Motor Vehicle Restraint Sys-tems and Booster Seats Safety Regula-tions. WA R N I N G
WA R N I N GNever hold an infant
or child in your arms
or on your lap when ri
ding in this vehicle,
even when you are wearing your seat belt.Never place any part of the seat belt youare wearing around an
infant or child.
Failure to follow these simple instructionscreates a risk of serious injury or death toyour child in the even
t of an accident or
sudden stop.
WA R N I N GYour vehicle is also equipped with a frontpassenger’s airbag.Never put REAR-FACING CHILDRESTRAINT SYSTEMS or INFANTRESTRAINT SYSTEMS in the front pas-senger seat. This places the infant tooclose to the passenger’s airbag. Duringdeployment of that airbag, the infant canbe seriously injured
or killed.
Rear-facing
child restraint systems or infant restraintsystems must only be used in the rear seat.Airbag
BK0249100US.book 28 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems
Seat and restraint systems 4-29
4
WA R N I N GFRONT-FACING CHILD RESTRAINTSYSTEMS should be used in the rear seatwhenever possible. If one must be used inthe front passenger seat, move the seat tothe most rearward po
sition and make sure
the child stays in the child restraint sys-tem, properly restrained. Failure to followthese instructions could result in seriousinjury or death to the child.WA R N I N GIt is important to use an approved rear-facing infant restraint until the infant isone year old (unless
the infant outgrows
the seat sooner). This allows the infant

Child restraint systems4-30 Seat and restraint systems
4
N00418801167
The outboard seating pos
itions in the second
row seat of your vehicle are equipped withlower anchors for attaching child restraintsystems compatible with the LATCH system.
N00418901201
Your vehicle has 3 at
tachment points on the
backside of the second
row seats. These are
for securing a child restraint system tetherstrap to each of the 3 rear seating positions inyour vehicle.
N00419000198N00419101301
1. In order to securely
fasten the tether strap,
remove the head restraint from the loca-tion where you wish to install the childrestraint system.2. Open the gap a little between the seatcushion (A) and the seatback (B) withyour hand to locate the lower anchors (C).
Installing a child restraint sys-tem using the LATCH (Lower Anchors and Tethers for chil-dren) system Lower anchor locations
NOTE
The symbols on the seatback show the loca-tion of the lower anchor points.
Tether anchor locations
Examples of child restraint sys-tems compatible with the LATCH system A- Rear-facing child restraint systemB- Front-facing child restraint systemC- Child restraint system lower anchor
connectors
D- Tether strap
(These are only examples.)
Using the LATCH system
BK0249100US.book 30 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems
Seat and restraint systems 4-31
4
3. For easier access, the seatback may berecline rearward.Push the anchor connectors (D) on thechild restraint system into the loweranchors (C) in accordance with theinstructions provided by the child restraintsystem’s manufacturer.After it is security fastened, adjust theseatback to 4 steps forward from mostreclined position.Remember, the lower anchors (C) pro-vided with your vehi
cle are designed to
secure suitable child restraint systemscompatible with the LATCH system inthe outboard positions of the secondrow seats only. The anchor connectorsare NOT designed to secure a suitablechild restraint system in the middleseating position of the second row seat.
4. Latch the tether strap hook (E) of the childrestraint system to the tether anchor bar(F) and tighten the tether strap so it issecurely fastened.5. Push and pull the chil
d restraint system in
all directions to ensure it is firmlysecured.
A- Vehicle seat cushionB- Vehicle seatbackC- Lower anchor
D- Connector
NOTE
In order to secure a child restraint systemcompatible with the LATCH system, use thelower anchor points in the outboard positionsof the second row seat. It is not necessary touse the vehicle’s seat
belt. The vehicle’s seat
belt, however, MUST be
used to secure a
child restraint system in the middle seatingposition of the second row seat.WA R N I N GIf there is any foreign material in oraround the lower an
chors, remove it
before installing the child restraint sys-tem. Also, make sure the seat belt is awayfrom, not looped through or otherwiseinterfering with, the child restraint sys-tem. If foreign matter is not removedand/or the seat belt
interferes with the
child restraint system, the child restraintsystem will not be secured properly, coulddetach and move forw
ard in the event of
sudden braking or an
accident, and could
result in injury to the child or other vehi-cle occupants.When the vehicle is
moving, do not adjust
the seat where the child restraint system isinstalled.
NOTE
If it is difficult to
latch the tether strap hook,
turn the hook sideways.WA R N I N GChild restraint system tether anchors aredesigned only to with
stand loads from cor-
rectly fitted child restraint systems. Underno circumstances are they to be used foradult seat belts, harnesses, for attachingother items, or equipment to the vehicle.
BK0249100US.book 31 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems4-32 Seat and restraint systems
4
N00407301553
With the exception of the driver, the seat beltin all other seating pos
itions can be converted
from normal Emergency Locking Retractor(ELR) mode, to Automatic Locking Retractor(ALR) mode. This mean
s that when you pull
the seat belt fully out of the retractor, theretractor will switch to its ALR child restraint
installation function.
Always use the ALR
child restraint installation function when youinstall a child restraint system using the seatbelt.Children 12 years old and under shouldalways be restrained in the rear seat, when-ever possible, although the front passengerseat belt can also be converted to ALR mode.
1. Place the child restraint system on the seatwhere you wish to install it.To help assure proper fitting of the childrestraint system, alwa
ys remove the head
restraint.When installing the front-facing childrestraint system on the second row seat,adjust the angle of the second row seat-back to the most upright position.
When using a child restraint in a rearseating position, always review theinstructions provided with that restraintto make sure it is compatible with thisvehicle and to understand how to properlyinstall it.Child restraints, incl
uding booster seats,
come in different sizes and configurations.Depending on where you
place these child
restraints, and depending on their size andconfiguration, you may not be able toaccess or properly use one or more adja-cent seat belt assemblies. If this occurs,the adjacent seating po
sition or positions
should not be used. Failure to use a seatbelt or improper use of a seat belt canresult in serious inju
ry or death should a
crash occur.
Installing a child restraint sys-tem using the seat belt (with emergency/auto
matic locking
mechanism)
WA R N I N G
WA R N I N GWhen you install a child restraint systemusing the seat belt, al
ways make sure the
retractor has been switched to the ALRchild restraint installation function. TheALR function will keep the child restraintsystem tightly secured to the seat.Failure to convert the retractor to theALR function may allow the childrestraint system to move forward duringsudden braking
or an accide
nt, resulting
in serious injury or
death to the child or
other occupants.
When using a child restraint in a rearseating position, al
ways review the
instructions provided with that restraintto make sure it is compatible with thisvehicle and to understand how to properlyinstall it.Child restraints, including booster seats,come in different sizes and configurations.Depending on where you
place these child
restraints, and depending on their size andconfiguration, you may not be able toaccess or properly use one or more adja-cent seat belt assemblies. If this occurs,the adjacent seating po
sition or positions
should not be used. Failure to use a seatbelt or improper use of a seat belt canresult in serious inju
ry or death should a
crash occur.
Installation
WA R N I N G
BK0249100US.book 32 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems
Seat and restraint systems 4-33
4
2. Route the seat belt through the childrestraint system acco
rding to the instruc-
tions provided by the child restraint sys-tem’s manufacturer. Then insert the seatbelt latch plate into
the buckle. Make sure
you hear a “click” when you insert thelatch plate into the buckle.
3. To activate the ALR child restraint instal-lation function, slowly pull the shoulderpart of the belt all the way out of theretractor until it stops. Then let the beltfeed back into the retractor.4. After the belt has retracted, tug on it.If the belt is in the ALR function, you willnot be able to pull it out. If the webbingcan be pulled out from retractor, the ALRfunction has not been activated and youwill need to repeat steps 3 and 4.
5. After confirming that the belt is locked,grab the shoulder part of the belt near thebuckle and pull up to remove any slackfrom the lap part of the belt allowing theslack to feed into the retractor. Remember,if the lap belt portion is not tight, the childrestraint system
will not be secure. It may
help to put your weight on the childrestraint system and/or push on its seat-back while pulling up on the belt (Seeillustration).
If your child restraint system requires the useof a tether strap, fasten the tether strap inaccordance with the following procedures.
BK0249100US.book 33 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Maintenance and inspection of seat belts4-34 Seat and restraint systems
4
6. Latch the tether strap hook (A) of thechild restraint system to the tether anchorbar (B) and tighten the tether strap so it issecurely fastened.
7. Before putting your child in the restraint,push and pull the restraint in all directionsto be sure it is firmly secure. Do thisbefore each use. If the child restraint sys-tem is not firmly s
ecure, repeat steps 1
through 6.8. To remove a child restraint system fromthe vehicle and deac
tivate the ALR mode,
remove the child from the restraint.Unlatch the buckle. Th
en remove the belt
from the restraint and let the belt fullyretract.9. Reinstall the head restraint.Refer to “Head restraints” on page 4-11.
N00407601628
Children who have outgrown a child restraintsystem should be seated in the rear seat andwear the seat belt. If the shoulder belt crossestheir face or neck, and/
or the lap belt crosses
their stomach, a commercially availablebooster seat must be used to raise the child sothat the shoulder belt
crosses their shoulder
and the lap belt remains positioned lowacross their hips. The booster seat should fitthe vehicle seat and ha
ve a label certifying
compliance with Federal Motor VehicleSafety Standards or Mo
tor Vehicle Restraint
Systems and Booster Se
ats Safety Regula-
tions.
N00407001390
Regularly check your seat belt buckles andtheir release mechanisms for positive engage-ment and release of the latch plate. Check theretractors for automatic locking when in theAutomatic Locking Retractor function.The entire seat belt assembly should bereplaced if the webbing shows any obvious
NOTE
If it is difficult to la
tch the tether strap hook,
turn the hook sideways.WA R N I N GChild restraint system tether anchors aredesigned only to with
stand loads from cor-
rectly fitted child restraint systems. Underno circumstances are they to be used foradult seat belts, harnesses, for attachingother items, or equipment to the vehicle.
Children who have outgrown child restraint systems
WA R N I N GAny child who is too small to properlywear a seat belt
must be properly
restrained in an appropriate childrestraint system, to reduce their risk ofserious injury or de
ath in an
accident.
A child should never be
left unattended in,
or unsupervised around, your vehicle.When you leave the ve
hicle, always take
the child out as well.Children can die from heat stroke if left ortrapped inside the vehicle, especially onhot days.Keep your vehicle locked when not in use.Keep your vehicle keys away from chil-dren.
Maintenance and inspection of seat belts
BK0249100US.book 34 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Supplemental Restraint System (SRS) - airbag
Seat and restraint systems 4-35
4
cuts, tears, increase in thickness in any sec-tion of the webbing from broken fibers, orsevere fading from sunlig
ht. All of these con-
ditions indicate a weakening of the belt,which may adversely affe
ct seat belt perfor-
mance in an accident.
N00407701889
This vehicle is equippe
d with a Supplemental
Restraint System (SRS), which includes air-bags for the driver and passengers.The SRS front airbags are designed to supple-ment the primary protection of the driver andfront passenger seat belt systems by provid-ing those occupants w
ith protection against
head and chest injuries
in certain moderate to
severe frontal collisi
ons. The SRS front air-
bags, together with sensors at the front of thevehicle and sensors attached to the frontseats, form an advanced airbag system.The SRS driver’s knee airbag is designed tosupplement the primary protection of thedriver’s seat belt system. It can reduce theforward movement of the driver’s lower legsand provide increased
overall body protection
in certain moderate to
severe frontal colli-
sions.The SRS side airbags and the curtain airbagsare also designed to supp
lement the seat belts.
The SRS side airbags provide the driver andfront passenger with pr
otection against chest
injuries by deploying the bag on the sideimpacted in moderate
to severe side impact
collisions. The SRS curtain airbags provide
the driver and the passengers on the front seatand the second row outboard seats with pro-tection against head injuries by deploying thecurtain airbag on the si
de impacted in moder-
ate to severe side imp
act collisions and by
deploying both curtain
airbags when a roll-
over is detected. The curtain airbags are alsodesigned to help reduce the risk of completeand partial ejection fro
m the vehicle through
side windows in both side impact and roll-over type accidents.The SRS airbags are NOT a substitute for useof the seat belts. For maximum protection inall types of accident
s, seat belts must
ALWAYS be worn by everyone who drives orrides in this vehicle
(with infants and small
children in an appropriate child restraint sys-tem in the rear seat, and older children buck-led in the rear seat). Refer to “Child restraintsystems” on page 4-27.
WA R N I N GDo not attempt to repair or replace anypart of the seat belt assemblies. This workshould be done
by an authorized
Mitsubishi Motors dealer. Failure to havean authorized Mits
ubishi Motors dealer
perform the work could reduce the effec-tiveness of the belts and could result in aserious injury or de
ath in an accident.
Never use an organic solvent to clean theseat belt webbing. Do not attempt tobleach or re-dye th
e seat belt webbing.
These may weaken the
seat belt webbing,
increasing risk of in
jury or death in an
accident.Clean seat belt webbing only with mildsoap or detergent solution and rinse itwith lukewarm water, and dry the seatbelt webbing completely before retractingit.
Supplemental Restraint Sys-tem (SRS) - airbag
BK0249100US.book 35 ページ ２０１７年５月１０日　水曜日　午前８時４９分