warning light MITSUBISHI OUTLANDER III 2018 Service Manual

Tire pressure monitoring system5-138 Features and controls
5
N00532701334
When the ignition switch is turned to the“ON” position or the operation mode is put inON, the tire pressure monitoring system
warning light normally
illuminates and goes
off a few seconds later.If one or more of the vehicle tires (except forthe spare tire) is signi
ficantly under-inflated,
the warning light will remain illuminatedwhile the ignition switch is in the “ON” posi-tion or the operation mode is put in ON.Refer to “If the warning light / display illumi-nates while driving” on page 5-140 and takethe necessary measures.
NOTE
The tire pressure monitoring system is not asubstitute for regularly
checking tire infla-
tion pressures.Be sure to check the tire inflation pressuresas described in “Tires” on page 9-15.The tire inflation pressure sensor (B) isinstalled in the illustrated location.• On vehicles with Type 1 sensor which hasthe metallic air valve (C), replace grommetand washer (D) with the new ones when thetire is replaced.• On vehicles with Type 2 sensor which hasthe rubber air valve (E), replace rubber airvalve (E) with new one when the tire isreplaced.
For details, please
contact your authorized
Mitsubishi Motors dealer.
Tire pressure monitoring sys-tem warning light / display
NOTE
Type 1Type 2
NOTE
In addition, the warni
ng display is displayed
on the information screen in the multi-infor-mation display.
BK0249100US.book 138 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Tire pressure monitoring system
Features and controls 5-139
5
Each tire, including the spare (if provided),should be checked monthly when cold andinflated to the inflation pressure recom-mended by the vehicle manufacturer on thevehicle placard or tire
inflation pressure label.
(If your vehicle has tires of a different sizethan the size indicated on the vehicle placardor tire inflation pressure label, you shoulddetermine the proper ti
re inflation pressure
for those tires.)As an added safety feat
ure, your vehicle has
been equipped with a tire pressure monitoringsystem (TPMS) that illuminates a low tirepressure telltale when
one or more of your
tires is significantly under-inflated.Accordingly, when the low tire pressure tell-tale illuminates, you
should stop and check
your tires as soon as possible, and inflatethem to the proper pressure. Driving on a sig-nificantly under-inflated
tire causes the tire to
overheat and can lead
to tire failure.
Under-inflation also reduces fuel efficiencyand tire tread life, and may affect the vehi-cle’s handling and stoppi
ng ability. Please
note that the TPMS is
not a substitute for
proper tire maintenance, and it is the driver’sresponsibility to
maintain corre
ct tire pres-
sure, even if under-infl
ation has not reached
the level to trigger illumination of the TPMSlow tire pressure telltale.Your vehicle has also
been equipped with a
TPMS malfunction indica
tor to indicate when
the system is not operating properly. TheTPMS malfunction indicator is combinedwith the low tire pressure telltale.When the system detects a malfunction, thetelltale will flash for approximately one min-ute and then remain c
ontinuously illuminated.
This sequence will c
ontinue upon subsequent
vehicle start-ups as long as the malfunctionexists.When the malfunction indicator is illumi-nated, the system may not
be able to detect or
signal low tire pr
essure as intended.
TPMS malfunctions ma
y occur for a variety
of reasons, including the installation ofreplacement or alternate tires or wheels on thevehicle that prevent the TPMS from function-ing properly. Always
check the TPMS mal-
function telltale after
replacing one or more
tires or wheels on your vehicle to ensure thatthe replacement or alternate tires and wheels
CAUTIONIf the tire pressure monitoring system warn-ing light does not illumi
nate when the igni-
tion switch is turned to the “ON” position orthe operation mode is put in ON, it meansthat the tire pressure monitoring system isnot working properly. Have the systeminspected by an authorized MitsubishiMotors dealer.In such situations, a malfunctioning of thesystem may be preventing the monitoring ofthe tire pressure. Avoid sudden braking,sharp turning and high-speed driving.If a malfunction is detected in the tire pres-sure monitoring system, the tire pressuremonitoring system warning light will blinkfor approximately 1 mi
nute and then remain
continuously illuminate
d. The warning light
will issue further warnings each time theengine is restarted as
long as the malfunction
exists.Check to see whether the warning light goesoff after few minutes driving.If it then goes off during driving, there is noproblem.However, if the warning light does not gooff, or if it blinks again when the engine isrestarted, have the
vehicle inspected by an
authorized Mitsubish
i Motors dealer.
In such situations, a malfunctioning of thesystem may be preventing the monitoring ofthe tire pressure. For safety reasons, whenthe warning light appears while driving,avoid sudden braking, sharp turning andhigh-speed driving.
NOTE
In addition, the warni
ng display is displayed
on the information screen in the multi-infor-mation display.
BK0249100US.book 139 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Tire pressure monitoring system5-140 Features and controls
5
allow the TPMS to cont
inue to function prop-
erly.
N00532801511
1. If the tire pressure monitoring systemwarning light illuminates, avoiding hardbraking, sharp steering maneuvers andhigh speeds. You should stop and adjustthe tires to the proper inflation pressure assoon as possible. Adjust the spare tire atthe same time. Refer to “Tires” on page9-15.
2. If the tire pressure monitoring systemwarning light remain
s illuminated after
you have been driving for about 20 min-utes after you adjust the tire inflation pres-sure, one or more of the tires may have apuncture. Inspect the tire and if it has apuncture, have it repaired by an autho-rized Mitsubishi Motors dealer as soon aspossible.
The tire pressure monitoring system may notwork normally in the following circum-stances:A wireless facility
or device using the
same frequency is near the vehicle.Snow or ice is stuck inside the fendersand/or on the wheels.The tire inflation pressure sensor’s batteryis dead.Wheels other than Mitsubishi genuinewheels are being used.Wheels that are not fitted with tire infla-tion pressure sensors are being used.Wheels whose ID codes are not memo-rized by the vehicle are used.Compact spare tire is fitted as a roadwheel.
If the warning light / display illuminates while driving
NOTE
In addition, the warni
ng display is displayed
on the information screen in the multi-infor-mation display.When inspecting or adjusting the tire pres-sure, do not apply excessive force to thevalve stem to
avoid breakage.
After inspecting or adjusting the tire pres-sure, always reinstall the valve cap on thevalve stem.Without the valve cap, di
rt or moisture could
get into the valve, resulting in damage to thetire inflation pressure sensor.Do not use metal valve caps, which maycause a metal reaction,
resulting in corrosion
and damage of the tire
inflation pressure sen-
sors.
Once adjustments have
been made, the warn-
ing light will go off after a few minutes ofdriving.WA R N I N GIf the warning light
/ display illuminates
while you are driving, avoid hard braking,sharp steering maneuvers and highspeeds.Driving with an under-inflated tireadversely affects vehi
cle performance and
can result in an accident.CAUTIONIf a tire has a puncture, replace that tire withthe spare tire. Driving on a punctured tirecould lead to an accident.The warning light / di
splay may not illumi-
nate immediately in the
event of a tire blow-
out or rapid leak.NOTE
NOTE
To avoid the risk of damage to the tire infla-tion pressure sensors, have any puncturedtire repaired by an authorized MitsubishiMotors dealer. If the tire repair is not done byan authorized Mitsubishi Motors dealer, it isnot covered by your warranty.Do not use an aerosol puncture-repair sprayon any tire.Such a spray could dama
ge the tire inflation
pressure sensors.Have any puncture repa
ired by an authorized
Mitsubishi Motors dealer.
BK0249100US.book 140 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Tire pressure monitoring system
Features and controls 5-141
5
A window tint that affects the radio wavesignals is installed.
N00532900081
If new wheels with new tire inflation pressuresensors are installed,
their ID codes must be
programmed into the tire pressure monitoringsystem. Have tire and
wheel replacement per-
formed by an authorized Mitsubishi Motorsdealer to avoid the ri
sk of damaging the tire
inflation pressure sensors. If the wheelreplacement is not done by an authorizedMitsubishi Motors dealer
, it is not covered by
your warranty.
N00584300026
In case that 2 sets of tire inflation pressuresensor ID are registered in the receiver, thevalid tire ID set can be changed by followingprocedure.[For vehicles equipped with color liquid crys-tal display meter]1. Operate the multi information displayswitch to switch the information screen tothe menu screen.Refer to “Multi information displayswitch” on page 5-157.Refer to “Changing the function settings”on page 5-167.2. Lightly press the multi information dis-play switch to select “ ” (tireID set change).
3. Hold down the multi information displayswitch for about 3 seconds or more. Thesetting changes to the selected tire ID set.4. The valid tire ID se
t is changed, and the
number of the tire pressure monitoringsystem (TPMS) SET indicator is changed.
[For vehicles equipped
with mono-color liq-
uid crystal display meter]1. Transit the display by multi informationdisplay switch until th
e tire pressure mon-
itoring system (TPMS) SET indicator isdisplayed.
NOTE
Tire inflation pressures vary with the ambi-ent temperature. If the
vehicle is subjected to
large variations in ambient temperature, thetire inflation pressures may be under-inflated(causing the warning light / display come on)when the ambient temperature is relativelylow. If the warning light / display comes on,adjust the tire inflation pressure.
Whenever the tires and wheels are replaced with new ones
CAUTIONThe use of non-genuine wheels will preventthe proper fit of the tire inflation pressuresensors, resulting air
leakage or damage of
the sensors.
Tire ID set change
NOTE
Each time this procedure is done, the tire IDset is changed. (1 - 2 - 1 - 2 …)only 1 set of ID is registered.
BK0249100US.book 141 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Multi Information display - Type 1
Features and controls 5-155
5
N00554901280
Each time you press this button, there is asound and the brightness
of the instruments
changes.
N00555001422
The multi information display displays warn-ings, the odometer, trip odometer, servicereminder, engine cool
ant temperature, fuel
remaining, outside temper
ature, selector lever
position, average and momentary fuel con-sumption, driving range
, average speed, etc.
It is also possible to change elements such asthe language and units used on the multiinformation display.[With ignition switch
or operation mode in
OFF]
CAUTIONThe red zone indicates an engine speedbeyond the range of safe operation.Select the correct select
or position to control
the engine speed so that
the tachometer indi-
cator does not enter the red zone.
Meter illumination control (Vehicle equipped with the multi information display - Type 1) 1- Brightness level2- Rheostat illumination button
NOTE
You can adjust to 8 different levels for whenthe front side-marker
lights are illuminated
and when they are not.If the vehicle is equippe
d with the automatic
light control, the light
switch is in a position
other than the “OFF” pos
ition and it is suffi-
ciently dark outside th
e vehicle, the meter
illumination switches automatically to theadjusted brightness.The brightness level
of the instruments is
stored when the ignition switch is turned tothe “OFF” or “LOCK” tion mode is put in OFF.If you press and hold the button for longerthan approximately 2 second when the frontside-marker lights ar
e illuminated, the
brightness level changes to the maximumlevel. Pressing and holding the button forlonger than approximately 2 second againreturns the brightness
level to the previous
level.
Multi Information display - Type 1
1-
Warning display screen
 P.5-161
2- Information screen
 P.5-157
Interrupt display screen
 P.5-160
3- Door ajar warning display screen
 P.5-161
4- Odometer
 P.5-162
5-
“ ” or “ ” mark indicator
 P.5-160
BK0249100US.book 155 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Multi Information display - Type 1
Features and controls 5-157
5
N00555101205
Each time the multi information displayswitch is operated, th
e buzzer sounds and the
multi information disp
lay changes between
information such as wa
rnings, trip odometer,
average and momentary fuel consumption,distance range, etc.
It is also possible to change elements such asthe language and units used on the multiinformation display by operating the multiinformation display switch.
N00555301177
Each time you lightly press the multi in
formation display switch, th
e display screen switches
in the following order.
Multi information display switch Information screen (With the igniti
on switch in “OFF” or “LOCK” po
sition or the operation mode in
OFF) *: When there is a warning display
BK0249100US.book 157 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Multi Information display - Type 1
Features and controls 5-159
5
N00556201232
Each time you lightly press the multi in
formation display switch, th
e display screen switches
in the following order.
Information screen (With the ignition
switch or the operation mode in ON)
*: When there is a warning display1-
Trip odometer
 P.5-162
2-
Trip odometer
 P.5-162
3- Driving range display
 P.5-165
ECO drive assist display
 P.5-166
4- Average fuel consumption display
 P.5-165ECO drive assist display
 P.5-166
5- Average speed display
 P.5-165
Momentary fuel consumption display
 P.5-166
6- ECO score display
 P.5-166
7- S-AWC operation displa
y (if so equipped)
 P.5-87
8- Service reminder
 P.5-163
BK0249100US.book 159 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Multi Information display - Type 1
Features and controls 5-161
5
Warning display screens with a “ ” or “ ”screen can be switched. If you want to switchthe display, press the multi information dis-play switch as follows.“ ”: Press lightly.“ ”: Press for approximately 2 seconds ormore.
N00579600021
When the warning is displayed, if youlightly press the multi information displayswitch a few times, the warning displayscreen you switched
from is redisplayed.
N00579700022
The operation status of each system is dis-played on the information screen.For further details, re
fer to the appropriate
page in the warn
ing display list.
Refer to “Other interrupt displays” on page5-197.
N00555201222
This is displayed when you press the multiinformation display switch and return fromthe warning display screen to the previousscreen.This mark is also displa
yed if there is another
warning other than the one displayed.When the cause of the warning display iseliminated, the warning goes out automat-ically.
N00529700030
If any of the doors or the liftgate is not com-pletely closed, this displays the open door orliftgate.If the speed increases to about 5 mph (8km/h) or higher with a door ajar, a tone willsound 4 times to inform you that a door isajar.
N00578200020
Shows the engine coolant temperature.If the coolant becomes hot, “ ” will blink.Pay careful attention to the engine coolanttemperature display while you are driving.
If you want to switch the displayRedisplay of a warning display screen Other interrupt displays
warning display screen
NOTE
When the warning is displayed, the warn-ing display screen can be redisplayed on theinformation screen.Refer to “Information sc
reen (with the igni-
tion switch in “OFF” or
“LOCK” position or
the operation mode in
OFF)” on page 5-157.
Refer to “Information sc
reen (with the igni-
tion switch or the operation mode in ON)” onpage 5-159.
Door ajar warning display screen
CAUTIONAlways make sure that
the warning display
goes out before beginning to drive.
Engine coolant temperature display
BK0249100US.book 161 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Multi Information display - Type 15-164 Features and controls
5
When the display is reset, the time until thenext periodic inspection
is displayed and the
warning display is no longer displayed whenthe ignition switch is switched from the“OFF” or “LOCK” position to the “ON”from OFF to ON.1. When you lightly press the multi informa-tion display switch, the informationscreen switches to the service reminderdisplay screen.2. Press and hold the multi information dis-play switch (for about 2 seconds or more)to display “ ” and make it flash. (If thereis no operation for
about 10 seconds with
this indicator flashing, the display returnsto the previous screen.)
3. With this indicator
flashing, if you lightly
press the multi information displayswitch, the screen switches from “---” to“CLEAR”. After that, the time until thenext periodic inspection is shown.
N00578400022
When the ignition switch is turned to the“ON” position or the ope
ration mode is put in
ON, the system check sc
reen is displayed for
about 4 seconds. If there is no fault, the infor-mation screen is displayed.If there is a fault, the screen changes to warn-ing display.Refer to “Warning di
splay list” on page
5-183.
CAUTIONThe customer is responsible for making surethat regular inspections and maintenance andperiodic inspections
and maintenance are
performed.Inspections and mainte
nance must be per-
formed to prevent accidents and malfunc-tions.NOTE
The “---” display cannot
be reset while the
ignition switch or the operation mode is inON.
When “---” is displayed, after a certain dis-tance and a certain pe
riod of time, the dis-
play is reset and th
e time until the next
periodic inspection is displayed.If you accidentally reset
the display, consult
an authorized Mitsubishi Motors dealer forassistance.
System check screen
NOTE
The system check screen display variesdepending on your equipment.NOTE
BK0249100US.book 164 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Multi Information display - Type 15-170 Features and controls
5
N00557201196
The temperature display unit can be switched.1. Press and hold the multi information dis-play switch (for about 2 seconds or more)to switch from the setting mode screen tothe menu screen.Refer to “Changing the function settings”on page 5-167.2. Lightly press the multi information dis-play switch to select “ ” (temperatureunit setting).3. Press and hold the multi information dis-play switch (for about 2 seconds or more)to switch in from °C to °F, or from °F to°C.The setting is changed to the selected tem-perature unit.
N00557301184
The language of the multi information displaycan be changed.1. Press and hold the mu
lti information dis-
play switch (for about 2 seconds or more)to change from the setting mode screen tothe menu screen.Refer to “Changing th
e function settings”
on page 5-167.2. Lightly press the multi information dis-play switch to se
lect “LANGUAGE” (lan-
guage setting).
3. Press and hold the multi information dis-play switch (for about 2 seconds or more)to display “LANGUAGE” (language set-ting).4. Lightly press the multi information dis-play switch to select
the desired language.
5. Press and hold the multi information dis-play switch (for about 2 seconds or more)to change the setting to the selected lan-guage.
Changing the temperature unit
NOTE
The temperature value on air conditionerpanel is switched in
conjunction with outside
temperature display unit of the multi infor-mation display.However, “°F” or “°C” are not shown to tem-perature display of
an air conditioner.
On vehicles equipped with the SmartphoneLink Display Audio, the temperature valueof the Smartphone Link Display Audio isswitched in conjunction
with outside temper-
ature display unit of the multi informationdisplay.If the battery is disconnected, the memory ofthe unit setting is erased and is automaticallyset to °F (°C).
Changing the display language
NOTE
NOTE
If the battery is disconnected, the memory ofthe language setting is erased and is automat-ically set to ENGLISH.If “---” is selected in the language setting, awarning message is not displayed when thereis a warning display or interrupt display.
BK0249100US.book 170 ページ ２０１７年５月１０日　水曜日　午前８時４９分