display MITSUBISHI OUTLANDER PHEV 2017 (in English) Manual PDF

ScreenCauseSolution (Reference)lForeign objects, such as dirt, snow or ice,
adhere to the bumper surface around the sensor.l Remove a foreign object on the bumper
surface around the sensor.
When the warning display does not disap- pear after having cleaned the bumper sur-face around the sensor, contact a MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Blind Spot Warning (BSW):
When there is a foreign objects on the
sensor” on page 7-83.l The Rear Cross Traffic Alert (RCTA) has
detected a vehicle that is approaching
your vehicle.l Pay special attention to the rear of your
vehicle.
Refer to “Rear Cross Traffic Alert
(RCTA)” on page 7-83.l There is a fault in the sensor.l We recommend you to contact a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Forward Collision Mitigation
System (FCM): When a problem is detec- ted” on page 7-70.
Refer to “Lane Departure Warning
(LDW): System problem warning” on page 7-87.
Refer to “Automatic high-beam system: System problem warning” on page 6-58.
Indication lamp, warning lamp, and information screen display list
6-40OGGE17E1Instruments and controls6

ScreenCauseSolution (Reference)lThe Forward Collision Mitigation System
(FCM), Lane Departure Warning (LDW)
and automatic high-beam system are tem-
porarily unavailable due to a high or low temperature of the sensor.l After the temperature of the sensor has
been in range, the system will automati-
cally return to operation.
Refer to “Forward Collision Mitigation System (FCM): When a problem is detec-
ted” on page 7-70.
Refer to “Lane Departure Warning
(LDW): System problem warning” on page 7-87.
Refer to “Automatic high-beam system: System problem warning” on page 6-58.l The sensor is temporarily unavailable due
to conditions such as the adhesion of con- taminants to the sensor or windscreen.This is not a malfunction.Refer to “Forward Collision Mitigation System
(FCM): When a problem is detected” on page
7-70.
Refer to “Lane Departure Warning (LDW):
System problem warning” on page 7-87.
Refer to “Automatic high-beam system: Sys- tem problem warning” on page 6-58.l There is a fault in the system of the auto-
matic high-beam.l We recommend you to contact a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Automatic high-beam system: System problem warning” on page 6-58.

Navigation information dis-
play*
E00531401061
On vehicles equipped with MITSUBISHI
Multi-Communication System (MMCS), the
following information on navigation will be
displayed when guidance location such as junction and destination is approached after
Indication lamp, warning lamp, and information screen display list
6-41OGGE17E1Instruments and controls6

you set the destination and started the routeguidance.
1- Guidance display
Shows the direction of vehicle travel andthe guidance location.2- Remaining distance display Shows the distance to the location where
the guidance is displayed.NOTEl Please read this section and also the separate
owner’s manual for MITSUBISHI Multi-
Communication System (MMCS).
Indication lamp, warning lamp, and information screen display list
6-42OGGE17E1Instruments and controls6 Direction of vehicle travel (Example) Destination Ferry terminal Tollbooth Intermediate destination (Example)

Other interrupt displays
E00524202211
ScreenSystem operation statusReferencelWhen you pressed the power switch and
the operation mode become the ACC
without depress the brake pedal, this
screen is displayed.
This screen will be displayed repeatedly at regular intervals while the operation mode of the power switch is put in ACC.l Place the select position in the “P” (PARK)
position, depress the brake pedal more
firmly than usual with the right foot. Then,
press the power switch.
Refer to “Starting and stopping the Plug-in Hybrid EV System” on page 7-14.l When Plug-in Hybrid EV System does
not start even if the operation mode of the power switch is put in ON, this screen is displayed.l When starting the Plug-in Hybrid EV Sys-
tem, you pressed the power switch with- out select position in the “P” (PARK) po-
sition.l Place the select position in the “P”
(PARK) position by pressing the electrical
parking switch, depress the brake pedal more firmly than usual with the right foot.
Then, press the power switch.
Refer to “Starting and stopping the Plug- in Hybrid EV System” on page 7-14.l Driving power is restricted by the safety
system as the Plug-in Hybrid EV System
has become too hot or too cold.l You do not have to take any actions. The
restriction on the driving power will be re- leased when the Plug-in Hybrid EV Sys- tem returns to the normal temperature.
Indication lamp, warning lamp, and information screen display list
6-43OGGE17E1Instruments and controls6

ScreenSystem operation statusReferencelIf the vehicle had not been refueled about
15 litres or more at one time for threemonths, the engine starts automatically
for the maintenance of the engine or the fuel system components.
This display may appear frequently de-
pending on the use conditions of your ve- hicle such as when fuel has been staying
in the fuel tank for a long time.
When the engine is running, this display shows the state where the drive battery is
charged, and the battery charge mode dis-
play (
) is displayed. But the
drive battery will not be full charge.
l Refill the 15 litres more at one time. This
display and battery charge mode display will disappear, and the engine will not au- tomatically start for maintenance.
If the fuel remaining display will be be- low half, you can refill the fuel more than
15 litres certainly.
l If you cannot refill the fuel due to the
large amount of remaining fuel, start the engine and drive the vehicle enough to re-duce the fuel level to approximately half
tank.l The accelerator pedal has been depressed
when the select position is in the “N”
(NEUTRAL) position.l When you start the vehicle, be sure to
check the select position indicator and make sure the select position is in the “D”(DRIVE) or “R” (REVERSE) position.
Then, please depress the accelerator ped-
al.
Refer to “Select position indicator” on page 7-18.l The selector lever has been operated when
the select position is in “P” (PARK) posi-
tion and the brake pedal is not depressed.l Operate the selector lever while depressed
firmly on the brake pedal.
The operation status of each system is displayed on the information screen. Refer to the appropriate page for the system for further details.
Indication lamp, warning lamp, and information screen display list
6-44OGGE17E1Instruments and controls6

ScreenSystem operation statusReferencelWhen charging of the drive battery is
completed.l Refer to “Charging” on page 3-02.lWhen the mode is changed by the opera-
tion of the 4WD lock switch or ECO mode
switch.l Refer to “ECO mode switch” on page
6-62.
l Refer to “4WD lock switch” on page
7-22.
l Refer to “When the ECO mode switch is
ON” on page 7-23.
Indication lamp, warning lamp, and information screen display list
6-45OGGE17E1Instruments and controls6

ScreenSystem operation statusReferencelWhen approaching the guidance location,
etc.l Refer to “Navigation information display”
on page 6-41.l When the EV priority mode is activated.l Refer to “EV switch” on page 7-25.lWhen the battery save mode is activated.l Refer to “Battery save mode switch” on
page 7-27.l When the battery charge mode is activa-
ted.l Refer to “Battery charge mode switch” on
page 7-28.l When the reversing sensor system detects
an obstruction.l Refer to “Reversing sensor system” on
page 7-94.
Indication lamp, warning lamp, and information screen display list
6-46OGGE17E1Instruments and controls6

ScreenSystem operation statusReferencelWhen the parking sensors detect an obsta-
cle.l Refer to “Parking sensors (Front/Rear)”
on page 7-98.l When the Forward Collision Mitigation
System (FCM) is activated or the timing of an alarm is changed.l Refer to “FCM and Ultrasonic misaccelera-
tion Mitigation System ON/OFF switch” on page 7-69.l When the Forward Collision Mitigation
System (FCM) is deactivated.l Refer to “FCM and Ultrasonic misacceler-
ation Mitigation System ON/OFF switch” on page 7-69.l When the Ultrasonic misacceleration Mit-
igation System is deactivated.l Refer to “To turn on/off the Ultrasonic
misacceleration Mitigation System” on page 7-79.l When the operation mode of the Lane De-
parture Warning (LDW) is switched.l Refer to “Lane Departure Warning
(LDW): How to operate LDW” on page 7-86.
Indication lamp, warning lamp, and information screen display list
6-47OGGE17E1Instruments and controls6

This informs you that a periodic inspection is due.ScreenSolutionWe recommend you to have it checked. Refer to “Service reminder” for further de-tails on page 6-12.
The setting for rest interval can be changed.
ScreenSolutionStop the vehicle in a safe place, stop the Plug-in Hybrid EV system, and take a rest.
Use this display as rough guide for taking rests during a long drive.
The interval from the start of your trip until this message is displayed can be set. Refer to “REST REMINDER” on page 6-21.
The display and buzzer alert the driver when the set time is reached. If you continue
to drive without having a rest, the buzzer sounds about every 5 minutes to encourage
you to take a rest.
l In the following cases, the time driven is reset and the display returns to the pre-
vious display screen. After this, when the set time is reached again, the buzzer
and display encourage you to take a rest. • The buzzer sounds 3 times.
• Put the operation mode in OFF.
• The multi information display switch is held for about 2 seconds or more.

Indication lamp, warning lamp, and information screen display list
6-48OGGE17E1Instruments and controls6

Plug-in Hybrid EV Systemwarning lamp
E00537300049
This warning lamp will illu-
minate when there is a fault at the Plug-in Hybrid EV
System.
Refer to “Service precau- tions” on page 11-02.
Normally, this warning lamp illuminates when the operation mode of the power switch
is put in ON, and goes off after a few sec-
onds.
CAUTIONl If the warning lamp illuminates and “EV
SYSTEM SERVICE REQUIRED STOP SAFELY” warning is displayed on the multi information display while the Plug-in Hy-
brid EV System is running, park your vehi-
cle in a safe place as soon as possible and contact a MITSUBISHI MOTORS Author-
ized Service Point to have the system checked.Regenerative brake warning
lamp
E00537200048
This warning lamp will illu-
minate when the regenera- tive brake cannot be used,
while the Plug-in Hybrid EV System is operating.
The warning is also dis-
played on the multi information display.
Normally, this warning lamp illuminates
when the operation mode of the power switch is put in ON, and goes off after the Plug-in
Hybrid EV System is activated.
CAUTIONl If the lamp illuminates while the Plug-in Hy-
brid EV System is operating, we recommend
you to have the vehicle inspected by a MITSUBISHI MOTORS Authorized Serv-
ice Point.Information screen display
E00524601117Brake warning display
E00524701525
This warning is displayed if you drive withthe parking brake still applied. The warning lamp in the instrument cluster only illumi-
nates when the parking brake is applied.
CAUTIONl If a vehicle is driven without releasing the
parking brake, the brake will be overheated, resulting in ineffective braking and possiblebrake failure.
If this warning is displayed, release the park-
ing brake.
Information screen display
6-52OGGE17E1Instruments and controls6