lock MITSUBISHI OUTLANDER XL 2013 Owners Manual

7-56 Vehicle care and maintenance
7
4. To install the bulb, perform the removal steps in reverse.
Daytime running lights (for vehicles equipped
with high intensity discharge headlights)
N00902000058
1. Turn the cap (A) counterclockwise to remove it.
CAUTION
!
Handle halogen light bulb with care. The gas inside
a halogen light bulb is highly pressurized, so drop-
ping, knocking, or scratching a halogen light bulb
can cause it to shatter.
Never hold the halogen light bulb with a bare hand,
dirty glove, etc.
The oil from your hand could cause the bulb to
break the next time the headlights are used.
If the glass surface is dirty, clean it with alcohol and
let it dry completely before installing the bulb.
*- Front of the vehicle
BK0150600US.book 56 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

Vehicle care and maintenance
7-57
7
2. Turn the socket (B) counterclockwise to remove it. 3. Turn the bulb counterclockwise while pressing it and pull
it out of the socket.
4. To install the bulb, perform the removal steps in reverse.*- Front of the vehicle
BK0150600US.book 57 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

Vehicle care and maintenance
7-59
7
2. Turn the socket (B) counterclockwise to remove it. 3. Pull the bulb out of the socket.
4. To install the bulb, perform the removal steps in reverse.*- Front of the vehicle
BK0150600US.book 59 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

7-60 Vehicle care and maintenance
7
Front turn signal lights
N00943400354
1. When replacing the bulb on the front passenger’s side,
remove the bolt (A) holding down the washer fluid reser-
voir spout and move the spout toward the rear of the vehi-
cle.2. Turn the socket (B) counterclockwise to remove it.*- Front of the vehicle
*- Front of the vehicle
BK0150600US.book 60 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

7-62 Vehicle care and maintenance
7
Side turn signal lights (on outside rearview mir-
ror) (if so equipped)
N00943500124
NOTE
The side turn signal lights (on outside rearview mirror)
uses an LED instead of the bulb.
Check with an authorized Mitsubishi Motors dealer or a
repair facility of your choice when the light needs to be
repaired or replaced.
Front fog lights
(if so equipped)
N00943600633
1. Turn the bezel (A) counterclockwise to remove it.*- Front of the vehicle
BK0150600US.book 62 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

7-64 Vehicle care and maintenance
7
3. While holding down the tab (D), pull out the socket (E). 4. Turn the bulb (F) counterclockwise to remove it.
BK0150600US.book 64 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

7-66 Vehicle care and maintenance
7
2. Turn the socket and bulb assembly counterclockwise to
remove it.NOTE
The tail and stop light uses an LED instead of the bulb.
Check with an authorized Mitsubishi Motors dealer or a
repair facility of your choice when the light needs to be
repaired or replaced.3. Pull the bulb out of the socket.B- Tail and stop light (LED) - cannot be replaced
C- Rear turn-signal light
BK0150600US.book 66 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

7-68 Vehicle care and maintenance
7
3. Turn the socket (A) counterclockwise to remove it. 4. Pull the bulb out of the socket.
5. To install the bulb, perform the removal steps in reverse.
BK0150600US.book 68 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

7-70 Vehicle care and maintenance
7
4. Remove the socket and bulb assembly (C) together by
turning it counterclockwise, and then remove the bulb by
pulling it out.
5. To install the bulb, perform the removal steps in reverse.
NOTE
When mounting the light unit, align the pins (D) on the
light unit with the hole in the body.
BK0150600US.book 70 ページ ２０１２年３月３０日　金曜日　午前１０時４３分

7-76 Vehicle care and maintenance
7
3. To install the bulb, perform the removal steps in reverse.NOTE
Before replacing the bulb, put the dome light (rear)/cargo
room light switch into the “OFF” position.

When mounting the lens, align the tabs (B) with the holes
on the vehicle body.
Glove compartment light
N00954200062
1. Turn the socket (A) counterclockwise to remove it.
BK0150600US.book 76 ページ ２０１２年３月３０日　金曜日　午前１０時４３分