warning lights MITSUBISHI SPYDER 1990 Service Repair Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1990, Model line: SPYDER, Model: MITSUBISHI SPYDER 1990Pages: 2103, PDF Size: 68.98 MB
Page 519 of 2103

ENGINE (TURBO)
ENGINE>
DIAGNOSTIC TEST MODEl When an abnormality is detected in one
of the sensors or actuators related to emis-
sion control, the CHECK
FUNCTION INDICATOR LAMP illuminates
as a warning to the driver.
l When an abnormality is detected in one
of the’ sensors or actuators, a
OTHER CONTROL FUNCTIONS
1. Fuel Pump Control
Turns the fuel pump relay ON current
is supplied to the fuel pump while the engine
is cranking or running.
2. A/C Compressor Clutch Relay Control Turns the A/C compressor clutch ON and
OFF.
3. Fan Relay Control
The radiator fan and condenser fan speeds
are controlled in response to the engine
coolant temperature and vehicle speed.
4. Fuel
Control
Supplies current to fuel pressure solenoid
coil to raise the fuel pressure so that the
fuel does not vaporize when the engine
is started while it is warm.
trouble code ‘the,,
normality is output.
lThe RAM data inside the that
to the sensors and actuators can be read’
by
scan’ tool.
addition, the actuators can be controlled
under certain
5. Charge Control
Controls the intake charge pressure by con-
trolling the duty of the turbocharger
gate solenoid!
6. Intake Pressure Gauge’ Control Indicates the intake charge pressure on
the
7. Generator Output Current Control
Prevents generator output current from in-
creasing idle speed from
dropping at times such as when the head-
lights are turned on.
8.Evaporative Emission Purge Solenoid Con-
trol Engine (TURBO)>
Refer to
17.
Evaporative Emission Purge Solenoid Con-
trol GROUP 17.
9. EGR Solenoid’ Control
Refer to GROUP
,,
,
TSB Revision
Page 1706 of 2103
![MITSUBISHI SPYDER 1990 Service Repair Manual ABS Troubleshooting , ,
INSPECTION PROCEDURE 3When ignition key is turned to “ON” (engine stopped ),
ABS warning light does not illuminate
[Comment]When power is supplied to the MITSUBISHI SPYDER 1990 Service Repair Manual ABS Troubleshooting , ,
INSPECTION PROCEDURE 3When ignition key is turned to “ON” (engine stopped ),
ABS warning light does not illuminate
[Comment]When power is supplied to the](/img/19/57345/w960_57345-1705.png)
ABS Troubleshooting , ,
INSPECTION PROCEDURE 3When ignition key is turned to “ON” (engine stopped ),
ABS warning light does not illuminate
[Comment]When power is supplied to the ABS-ECU, the valve relay changes from to ON by the initial check, and thus even if there is a problem with the circuit between
ABS light and ABS-ECU, the light will illuminate once when the valve relay
is OFF.
Accordingly, the cause of the light not illuminatin g is probably an open circuit in the
light power circuit, a blown light bulb, or an open circuit in both the circuit between
the ABS
light and the ABS-ECU and the circuit between the ABS light and the ABS valve relay.When other lights also do not illuminate, the cause is probably a blown fuse.
Measure at combination meter connector
l Disconnect the connector and mea-
sure at the harness side.
l Ignition Switch ON
lVoltage between terminal 10 and body
OK Battery positive voltage Check trouble symptoms
Measure at combination meter connector
sure at the combination meter side.
l Continuitv between terminals
R e p l a c e t h e
OK Continuity ,
OK
Check the harnesses between the ABS valve relay and the combination meter,
a n d b e t w e e n t h e A B S - E C U a n d
combination meter (common section).
if necessary.
INSPECTION PROCEDURE 4
TSB Revision.
Even after the engine is started, the ABS Warning l ight ,remains illuminated.. .
[Comment]There is probably a short in the ABS warning light illumination circuit.l Malfunction of combination meterl Malfunction of ABS valve relayl Malfunction of ABS-ECU. ,
NOTE
This trouble symptom is limited to cases where comm unication with the scan tool is’
is normal) and the diagnostic trouble code is a normal diagnostic trouble code..YESDisconnect the ABS-ECU connector Does the light remain illuminated?
NO
Short circuit inside the combination or in the harnessbetween the meter and
Replace the ABS-ECU.
Page 1745 of 2103
![MITSUBISHI SPYDER 1990 Service Repair Manual ABS Troubleshooting
INSPECTION PROCEDURE 3
ignition key is turned to “ON’? (engine stopped),ProbableABS warning light does not illuminate
[Comment]When power is supplied to the ABS- MITSUBISHI SPYDER 1990 Service Repair Manual ABS Troubleshooting
INSPECTION PROCEDURE 3
ignition key is turned to “ON’? (engine stopped),ProbableABS warning light does not illuminate
[Comment]When power is supplied to the ABS-](/img/19/57345/w960_57345-1744.png)
ABS Troubleshooting
INSPECTION PROCEDURE 3
ignition key is turned to “ON’? (engine stopped),ProbableABS warning light does not illuminate
[Comment]When power is supplied to the ABS-ECU, the valve relay changes from to OFF ON by the initial check, and thus even if there is a problem with the circuit betweenABS warning light and ABS-ECU, the light will illum inate once when the valve relayis OFF.Accordingly, the cause of the light not illuminating is probably an open circuit in the
light power circuit, a blown light bulb, or an open circuit in both the circuit between
the ABS
liaht and the ABS-ECU and the circuit between the ABS
l Blown fuselBurntout light. bulblMalfunction of wiring. or connector
.
light and the relay.When other lights also do not illuminate, the cause is probab ly a blown fuse.
N GNG ,
Measure at combination meter connector Checkl and l Disconnect the connector and mea-
l Disconnect the connector and mea-
sure atthe combination meter side.
l Continuitv between terminals
OK Continuity
OK
Not
Replace combination meter.
, Check the harnesses between the valve relay and the combination meter,
a n d b e t w e e n t h e A B S - E C U a n d
combination meter (common section).
Repair, if necessary.
INSPECTION PROCEDURE 4
Even after the engine is started, the ABS warning l ight Probable cause ,
remains illuminated.
[Comment]There is probably a short in the ABS light illumination l Malfunction of meter
l Malfunction of valve relay
l Malfunction of ABS-ECU
l Malfunction of wiring
NOTE
This trouble symptom is limited to cases where comm unication with the scan tool is
supply is normal) and the diagnostic trouble code is a normal diagnostic trouble code.
Disconnect the ABS-ECU connector Short circuit inside the combination meter or in the Does the ABS warning light remain illuminated? between the combination meter and the ABS-ECU.
NO
Replace the ABS-ECU.
TSB Revision