heating NISSAN 350Z 2007 Z33 Automatic Air Conditioner Workshop Manual

ATC-2Revision: 2006 November2007 350Z WORK FLOW ...................................................... 34
SYMPTOM TABLE .............................................. 34
Component Parts and Harness Connector Location ... 35
ENGINE COMPARTMENT .................................. 35
PASSENGER COMPARTMENT .......................... 36
Schematic ............................................................... 37
Wiring Diagram — A/C — ....................................... 38
Auto Amp. Terminals and Reference Value ............ 43
PIN CONNECTOR TERMINAL LAYOUT ............ 43
TERMINALS AND REFERENCE VALUE FOR
UNIFIED METER AND A/C AMP. ........................ 43
Self-diagnosis Function .......................................... 45
DESCRIPTION .................................................... 45
FUNCTION CONFIRMATION PROCEDURE ...... 46
AUXILIARY MECHANISM: TEMPERATURE
SETTING TRIMMER ........................................... 50
AUXILIARY MECHANISM: FOOT POSITION
SETTING TRIMMER ........................................... 51
AUXILIARY MECHANISM: INLET PORT MEM-
ORY FUNCTION ................................................. 51
Operational Check .................................................. 53
CHECKING BLOWER ......................................... 53
CHECKING DISCHARGE AIR ............................ 53
CHECKING INTAKE DOOR ................................ 53
CHECKING TEMPERATURE DECREASE ......... 53
CHECKING TEMPERATURE INCREASE .......... 53
CHECKING A/C SWITCH ................................... 53
Power Supply and Ground Circuit for Auto Amp. ... 54
INSPECTION FLOW ........................................... 54
COMPONENT DESCRIPTION ............................ 54
DIAGNOSIS PROCEDURE FOR A/C SYSTEM ... 55
LAN System Circuit ................................................ 56
DIAGNOSIS PROCEDURE FOR LAN CIRCUIT ... 56
Mode Door Motor Circuit ........................................ 60
INSPECTION FLOW ........................................... 60
SYSTEM DESCRIPTION .................................... 61
COMPONENT DESCRIPTION ............................ 62
DIAGNOSIS PROCEDURE FOR MODE DOOR
MOTOR ............................................................... 62
Air Mix Door Motor Circuit ...................................... 63
INSPECTION FLOW ........................................... 63
SYSTEM DESCRIPTION .................................... 64
COMPONENT DESCRIPTION ............................ 65
DIAGNOSIS PROCEDURE FOR AIR MIX DOOR ... 65
Air Mix Door Motor PBR Circuit .............................. 65
DIAGNOSIS PROCEDURE FOR AIR MIX DOOR
MOTOR PBR ....................................................... 65
Intake Door Motor Circuit ........................................ 66
INSPECTION FLOW ........................................... 66
SYSTEM DESCRIPTION .................................... 67
COMPONENT DESCRIPTION ............................ 68
DIAGNOSIS PROCEDURE FOR INTAKE DOOR
MOTOR ............................................................... 68
Blower Motor Circuit ............................................... 69
INSPECTION FLOW ........................................... 69
SYSTEM DESCRIPTION .................................... 70
COMPONENT DESCRIPTION ............................ 71
DIAGNOSIS PROCEDURE FOR BLOWER
MOTOR ............................................................... 71COMPONENT INSPECTION ............................... 73
Magnet Clutch Circuit .............................................. 74
INSPECTION FLOW ............................................ 74
SYSTEM DESCRIPTION ..................................... 75
DIAGNOSIS PROCEDURE FOR MAGNET
CLUTCH .............................................................. 75
COMPONENT INSPECTION ............................... 80
Insufficient Cooling .................................................. 81
INSPECTION FLOW ............................................ 81
PERFORMANCE TEST DIAGNOSIS .................. 83
PERFORMANCE CHART .................................... 85
TROUBLE DIAGNOSIS FOR UNUSUAL PRES-
SURE ................................................................... 86
Insufficient Heating ................................................. 89
INSPECTION FLOW ............................................ 89
Noise ....................................................................... 90
INSPECTION FLOW ............................................ 90
Self-diagnosis ......................................................... 91
INSPECTION FLOW ............................................ 91
Ambient Sensor Circuit ........................................... 92
COMPONENT DESCRIPTION ............................ 92
AMBIENT TEMPERATURE INPUT PROCESS ... 92
DIAGNOSIS PROCEDURE FOR AMBIENT
SENSOR .............................................................. 92
COMPONENT INSPECTION ............................... 94
In-vehicle Sensor Circuit ......................................... 94
COMPONENT DESCRIPTION ............................ 94
DIAGNOSIS PROCEDURE FOR IN-VEHICLE
SENSOR .............................................................. 95
COMPONENT INSPECTION ............................... 96
Sunload Sensor Circuit ........................................... 97
COMPONENT DESCRIPTION ............................ 97
SUNLOAD INPUT PROCESS ............................. 97
DIAGNOSIS PROCEDURE FOR SUNLOAD
SENSOR .............................................................. 97
COMPONENT INSPECTION ............................... 99
Intake Sensor Circuit .............................................100
COMPONENT DESCRIPTION ..........................100
DIAGNOSIS PROCEDURE FOR INTAKE SEN-
SOR ...................................................................100
COMPONENT INSPECTION .............................101
A/C CONTROLLER .................................................102
Removal and Installation .......................................102
REMOVAL ..........................................................102
INSTALLATION ..................................................102
Disassembly and Assembly ..................................102
AUTO AMP ..............................................................103
Removal and Installation of Unified Meter and A/C
Amp. ......................................................................103
REMOVAL ..........................................................103
INSTALLATION ..................................................103
AMBIENT SENSOR ................................................104
Removal and Installation .......................................104
REMOVAL ..........................................................104
INSTALLATION ..................................................104
IN-VEHICLE SENSOR ............................................105
Removal and Installation .......................................105
REMOVAL ..........................................................105
INSTALLATION ..................................................105

ATC-34
TROUBLE DIAGNOSIS
Revision: 2006 November2007 350Z
How to Perform Trouble Diagnosis for Quick and Accurate RepairNJS0000R
WORK FLOW
SYMPTOM TABLE
*1ATC-53, "Operational Check"
SHA900E
Symptom Reference Page
A/C system does not come on. Go to Trouble Diagnosis Procedure for A/C system.ATC-54, "
Power
Supply and
Ground Circuit for
Auto Amp."
Air outlet does not change.
Go to Trouble Diagnosis Procedure for Mode Door Motor. (LAN)ATC-60, "Mode
Door Motor Cir-
cuit"Mode door motor does not operate normally.
Discharge air temperature does not change.
Go to Trouble Diagnosis Procedure for Air Mix Door Motor. (LAN)AT C - 6 3 , "
Air Mix
Door Motor Cir-
cuit"Air mix door motor does not operate nor-
mally.
Intake door does not change.
Go to Trouble Diagnosis Procedure for Intake Door Motor. (LAN)AT C - 6 6 , "
Intake
Door Motor Cir-
cuit"Intake door motor does not operate normally.
Blower motor operation is malfunctioning. Go to Trouble Diagnosis Procedure for Blower Motor.AT C - 6 9 , "
Blower
Motor Circuit"
Magnet clutch does not engage. Go to Trouble Diagnosis Procedure for Magnet Clutch.AT C - 7 4 , "Magnet
Clutch Circuit"
Insufficient cooling Go to Trouble Diagnosis Procedure for Insufficient Cooling.ATC-81, "Insuffi-
cient Cooling"
Insufficient heating Go to Trouble Diagnosis Procedure for Insufficient Heating.ATC-89, "Insuffi-
cient Heating"
Noise Go to Trouble Diagnosis Procedure for Noise.AT C - 9 0 , "Noise"
Self-diagnosis cannot be performed. Go to Trouble Diagnosis Procedure for Self-diagnosis.AT C - 9 1 , "Self-
diagnosis"

TROUBLE DIAGNOSIS
ATC-53
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2006 November2007 350Z
Operational CheckNJS0000X
The purpose of the operational check is to check if the individual system operates properly.
CHECKING BLOWER
1. Turn fan control dial to 1st speed. Blower should operate on low speed.
2. Turn fan control dial to 2nd speed, and continue checking blower speed until all speeds are checked.
3. Leave blower on max. speed.
If NG, go to trouble diagnosis procedure for AT C - 6 9 , "
Blower Motor Circuit" .
If OK, continue the check.
CHECKING DISCHARGE AIR
1. Turn mode control dial to each position.
2. Confirm that discharge air comes out according to the air distri-
bution table. Refer to AT C - 3 0 , "
Discharge Air Flow" .
Intake door position is checked in the next step.
If NG, go to trouble diagnosis procedure for AT C - 6 0 , "
Mode Door
Motor Circuit" .
If OK, continue the check.
NOTE:
Confirm that the compressor clutch is engaged (sound or visual
inspection) and intake door position is at FRESH when the D/F, D/F2
or DEF position are selected.
CHECKING INTAKE DOOR
1. Press intake switch. Recirculation LED should illuminate.
2. Press intake switch again. Fresh LED should illuminate.
3. Listen for intake door position change. (Slight change of blower sound can be heard.)
If NG, go to trouble diagnosis procedure for AT C - 6 6 , "
Intake Door Motor Circuit" .
If OK, continue the check.
CHECKING TEMPERATURE DECREASE
1. Turn temperature control dial until 18°C (60°F).
2. Check for cold air at discharge air outlets.
If NG, go to trouble diagnosis procedure for AT C - 8 1 , "
Insufficient Cooling" .
If OK, continue the check.
CHECKING TEMPERATURE INCREASE
1. Turn temperature control dial until 32°C (90°F).
2. Check for hot air at discharge air outlets.
If NG, go to trouble diagnosis procedure for AT C - 8 9 , "
Insufficient Heating" .
If OK, continue the check.
CHECKING A/C SWITCH
Turn fan control dial to AUTO position. (Compressor is turned ON automatically.)

Confirm that the compressor clutch engages (sound or visual inspection). (Discharge air and blower
speed will depend on ambient, in-vehicle, and set temperatures.)
If NG, go to trouble diagnosis procedure for AT C - 5 4 , "
Power Supply and Ground Circuit for Auto Amp." , then
if necessary, trouble diagnosis procedure for AT C - 7 4 , "
Magnet Clutch Circuit" .
If all operational checks are OK (symptom cannot be duplicated), go to Incident Simulation Tests in GI-27,
"How to Perform Efficient Diagnosis for an Electrical Incident" and perform tests as outlined to simulate driv-
ing conditions environment. If symptom appears, refer to AT C - 3 4 , "
SYMPTOM TABLE" and perform applica-
ble trouble diagnosis procedures.Conditions : Engine running at normal operating temperature
RJIA2110E

TROUBLE DIAGNOSIS
ATC-89
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2006 November2007 350Z
Insufficient HeatingNJS00017
SYMPTOM: Insufficient heating
INSPECTION FLOW
*1AT C - 5 3 , "Operational Check"*2ATC-46, "FUNCTION CONFIRMA-
TION PROCEDURE", see No. 1.*3ATC-46, "
FUNCTION CONFIRMA-
TION PROCEDURE", see No. 5 to 7.
*4AT C - 6 3 , "
Air Mix Door Motor Cir-
cuit"
*5ATC-46, "FUNCTION CONFIRMA-
TION PROCEDURE", see No. 9.*6ATC-56, "
LAN System Circuit"
*7AT C - 6 9 , "Blower Motor Circuit"*8ATC-63, "Air Mix Door Motor Circuit"*9EC-223, "DTC P0117, P0118 ECT
SENSOR"
*10CO-10, "Changing Engine Coolant"*11CO-15, "Checking Radiator Cap"
SJIA1131E